{"title":"Coaters","description":"\u003cp\u003e\u003cstrong\u003eCoaters turn a slurry, ink, or precursor solution into a controlled film — and the right deposition method depends almost entirely on viscosity, wet thickness, substrate format, and how solvent comes off.\u003c\/strong\u003e This section groups the coating platforms most commonly used in battery, fuel-cell, electrolyzer, SOFC\/SOEC, and sensor R\u0026amp;D, so you can pick a method by the physics of your formulation rather than by what happens to be on the bench.\u003c\/p\u003e\n\n\u003cp\u003eBrowse by deposition method:\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/collections\/dip-coaters\"\u003eDip Coaters\u003c\/a\u003e\u003c\/strong\u003e — withdraw a substrate from a precursor bath at a controlled speed; the workhorse for sol-gel layers, layer-by-layer assembly, separator and membrane functionalization, and protective overcoats, with nano-speed, multi-position carousel, and roll-to-roll variants.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/collections\/ultrasonic-spray-coaters\"\u003eUltrasonic Spray Coaters\u003c\/a\u003e\u003c\/strong\u003e — piezo-atomized low-velocity mist that deposits dilute catalyst inks and ionomer dispersions onto membranes, GDLs, and fragile or non-flat substrates; the standard tool for CCMs and gas-diffusion electrodes.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/collections\/electrospinning-coaters\"\u003eElectrospinning Coaters\u003c\/a\u003e\u003c\/strong\u003e — high-voltage Taylor-cone jet that draws non-woven nanofiber mats for separators, interlayers, catalyst supports, and solid-electrolyte scaffolds, with environmental control over humidity and temperature.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/collections\/tape-casting-coaters\"\u003eTape Casting Coaters\u003c\/a\u003e\u003c\/strong\u003e — doctor-blade and wire-rod metering on a vacuum bed for electrode pastes, ceramic green tapes (LLZO, LATP, LAGP, MLCC), and thick fuel-cell catalyst layers, with IR or top\/bottom heating to prevent skinning.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/collections\/screen-print-coaters\"\u003eScreen Print Coaters\u003c\/a\u003e\u003c\/strong\u003e — squeegee-and-mesh patterned deposition of thick, high-viscosity pastes for SOFC\/SOEC electrolytes and electrodes, thick-film sensors, and tubular cells, in manual, semi-automatic flat-bed, and curved-substrate formats.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e\u003ca href=\"\/collections\/press-accessories\"\u003eAccessories\u003c\/a\u003e\u003c\/strong\u003e — slot-die heads, adjustable-gap film applicators, R2R unwind\/rewind handling units, and matched cell-format fixtures that pair with the coaters above.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eIf your film is sub-micron and your ink is dilute, start with ultrasonic spray; for thick electrodes and ceramic tapes, use tape casting; for patterned thick-film deposits on rigid substrates, screen print; for nanofiber mats, electrospinning; for sol-gel and conformal overcoats, dip. For matched tooling and consumables, see \u003ca href=\"\/collections\/press-accessories\"\u003eAccessories\u003c\/a\u003e; for the broader equipment range, see Laboratory Equipment.\u003c\/p\u003e\n","products":[{"product_id":"esstcchvb","title":"ECS-SS Tape Casting Coater with Heating Vacuum Bed (L200*W120 mm, 120℃), ESSTCCHVB","description":"\u003cp\u003eFor lab-scale tape casting (also known as doctor blade coating), the most effective systems combine a high-precision vacuum chuck to hold the substrate flat and an integrated heating element to control the drying process. These features are critical for producing uniform, crack-free films for battery electrodes, fuel cell membranes, or ceramic tapes.\u003c\/p\u003e\n\u003cp\u003eThe key selection criteria of an appropriate tape casting coater: (1) \u003cstrong\u003eVacuum Bed\u003c\/strong\u003e: Essential for keeping thin foils (like Copper or Aluminum) or polymer films from wrinkling during the coating stroke. (2) \u003cstrong\u003eHeating Method\u003c\/strong\u003e: Top heating (infrared or convection) dries the slurry surface first, while bottom heating (heated bed) transfers heat through the substrate. (3) \u003cstrong\u003eCoating Speed\u003c\/strong\u003e: Look for variable speed control (typically 0–100 mm\/s) to match the rheology of your specific slurry. (4) \u003cstrong\u003eDoctor Blade Compatibility\u003c\/strong\u003e: Most of these units are compatible with adjustable micrometer doctor blades or fixed-gap film applicators.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSTCCHVB (ESS-TCCHVB)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, single phase, 50\/60Hz, 280 W \u003c\/li\u003e\n\u003cli\u003eA DC24V converter is included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eCoating Area\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe whole vacuum bed area is L200*W120mm, which enable the effective coating area is L190mm * W100 mm (depends on the film applicator is used).  \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoating Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e10-48 mm\/s\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eBottom Heating Temperature \u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 120 ℃ (single-point control)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eFilm Applicator (\u003cspan style=\"color: rgb(253, 8, 8);\"\u003eOptional\u003c\/span\u003e)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 1\u003c\/strong\u003e: Four Side Film Applicator with Fixed Gap\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            The standard one (effective coating width of 80mm) has four-side\u003c\/p\u003e\n\u003cp\u003e            gap of 100 um, 150 um, 200 um, and 250 um. Other options can\u003c\/p\u003e\n\u003cp\u003e            be found here (\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafsfafg?variant=47491848863974\"\u003eESSAFSFAFG\u003c\/a\u003e).\u003c\/p\u003e\n\u003cp\u003e            \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCHVB_02_160x160.png?v=1774764406\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 2\u003c\/strong\u003e: Standard Film Applicator with Adjustable Gap (\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafaw80?variant=47492067393766\"\u003eESSAFAW80\u003c\/a\u003e)\u003cbr\u003e\n\u003cdiv style=\"text-align: left;\"\u003eThe standard coating width is 80 mm and adjustable gap is 0-3 mm (resolution: 5 um).  \u003c\/div\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafaw80?variant=47492067393766\"\u003e\u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCHVB_03_160x160.png?v=1774765217\"\u003e\u003c\/a\u003e\u003c\/div\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eVacuum Pump\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAn individual pump with DC24V power input is included \u003c\/li\u003e\n\u003cli\u003e8 mm O.D. tubing connection\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL360 * W220 * H210 mm (antechamber and glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~20 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0272884217301475\"\u003eJ. Ko, et al., Thin cathode for thermal batteries using a tape-casting process, Ceramic International, 2017, 43, 5789-5793\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.4c18516\"\u003eH. Zhao, et al., Tape-Casting Fabrication Techniques for Garnet-Based Membranes in Solid-State Lithium-Metal Batteries: A Comprehensive Review, ACS Appl. Mater. Interfaces 2024, 16, 50, 68772–68793\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Coater + Four-Side Film Applicator with Fix Gap","offer_id":47491696754918,"sku":"ESSTCCHVBFS","price":3499.0,"currency_code":"USD","in_stock":true},{"title":"Coater + Standard Film Applicator with Adjustable Gap","offer_id":47491696787686,"sku":"ESSTCCHVBS","price":3799.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCHVB_main.png?v=1774767247"},{"product_id":"essafsfafg","title":"Four-Side Film Applicator with Fixed Gap for Tape Casting Coater (ESSTCCHVB), ESSAFSFAFG","description":"\u003cp\u003eFor lab-scale tape casting and thin-film preparation, a four-side film applicator (also known as a Frame-type or Quadruple applicator) is a highly efficient tool. It allows you to cast films of four different fixed thicknesses using a single device by simply rotating it to the desired side.\u003c\/p\u003e\n\u003cp\u003eThe benefits of Fixed-Gap Applicators: (1) \u003cstrong\u003eHigh Repeatability\u003c\/strong\u003e: Unlike adjustable micrometer blades, fixed-gap applicators eliminate human error in setting the height. This ensures that every film cast is exactly the same thickness. (2) \u003cstrong\u003eDurability\u003c\/strong\u003e: Typically machined from hardened stainless steel or corrosion-resistant alloy, making them compatible with various solvents and easy to clean. (3) \u003cstrong\u003eEfficiency\u003c\/strong\u003e: The four-sided design is ideal for researchers who frequently switch between a set range of thicknesses (e.g., 50µm, 100µm, 150µm, 200µm) for comparative studies.\u003c\/p\u003e\n\u003cp\u003eThe four-side film applicator with fixed gap is specially designed as accessories for mini tap casting coater (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esstcchvb?variant=47491696754918\"\u003eESSTCCHVB\u003c\/a\u003e) \u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSAFSFAFG (ESS-A-FSFAFG)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eEffective Coating Width\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e80 um (SS304)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eFilm Applicator Types\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e5 um, 10 um, 15 um, 20 um\u003c\/li\u003e\n\u003cli\u003e10 um, 15 um, 20 um, 25 um\u003c\/li\u003e\n\u003cli\u003e20 um, 40 um, 60 um, 80 um\u003c\/li\u003e\n\u003cli\u003e25 um, 50 um, 75 um, 100 um\u003c\/li\u003e\n\u003cli\u003e30 um, 60 um, 90 um, 120 um\u003c\/li\u003e\n\u003cli\u003e50 um, 75 um, 100 um, 150 um\u003c\/li\u003e\n\u003cli\u003e50 um, 100 um, 150 um, 200 um\u003c\/li\u003e\n\u003cli\u003e100 um, 150 um, 200 um, 250 um\u003c\/li\u003e\n\u003cli\u003e100 um, 200 um, 300 um, 400 um\u003c\/li\u003e\n\u003cli\u003e250 um, 500 um, 750 um, 1000 um\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eNote\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIt is an accessory for mini tape casting coater (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esstcchvb?variant=47491696754918\"\u003eESSTCCHVB\u003c\/a\u003e) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL100 * W22 * H22 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0272884217301475\"\u003eJ. Ko, et al., Thin cathode for thermal batteries using a tape-casting process, Ceramic International, 2017, 43, 5789-5793\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.4c18516\"\u003eH. Zhao, et al., Tape-Casting Fabrication Techniques for Garnet-Based Membranes in Solid-State Lithium-Metal Batteries: A Comprehensive Review, ACS Appl. Mater. Interfaces 2024, 16, 50, 68772–68793\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"5-10-15-20 um","offer_id":47491848863974,"sku":"ESSAFSFAFG20","price":499.0,"currency_code":"USD","in_stock":true},{"title":"10-15-20-25 um","offer_id":47491848896742,"sku":"ESSAFSFAFG25","price":519.0,"currency_code":"USD","in_stock":true},{"title":"20-40-60-80 um","offer_id":47491998351590,"sku":"ESSAFSFAFG08","price":549.0,"currency_code":"USD","in_stock":true},{"title":"25-50-75-100 um","offer_id":47491998384358,"sku":"ESSAFSFAFG100","price":579.0,"currency_code":"USD","in_stock":true},{"title":"30-60-90-120 um","offer_id":47491998417126,"sku":"ESSAFSFAFG120","price":599.0,"currency_code":"USD","in_stock":true},{"title":"50-75-100-150 um","offer_id":47492010868966,"sku":"ESSAFSFAFG150","price":629.0,"currency_code":"USD","in_stock":true},{"title":"50-100-150-200 um","offer_id":47492010901734,"sku":"ESSAFSFAFG200","price":649.0,"currency_code":"USD","in_stock":true},{"title":"100-150-200-250 um","offer_id":47492010934502,"sku":"ESSAFSFAFG250","price":699.0,"currency_code":"USD","in_stock":true},{"title":"100-200-300-400 um","offer_id":47492010967270,"sku":"ESSAFSFAFG400","price":3499.0,"currency_code":"USD","in_stock":true},{"title":"250-500-750-1000 um","offer_id":47492011000038,"sku":"ESSAFSFAFG1000","price":799.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCHVB_02.png?v=1774771839"},{"product_id":"essafaw80","title":"Film Applicator (W=80 mm) with Adjustable Gap (0-3 mm) for Tape Casting Coater (ESSTCCHVB), ESSAFAW80","description":"\u003cp\u003eThe adjustable micrometer film applicator is the standard choice for tape casting coaters. Unlike fixed-gap versions, these allow you to fine-tune the gate height in 10-micron increments, which is essential when accounting for slurry shrinkage or when trying to hit a very specific dry-film target.\u003c\/p\u003e\n\u003cp\u003eThe 80mm width film applicator with adjustable gap (0-3 mm) is specially designed as accessories for mini tap casting coater (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esstcchvb?variant=47491696754918\"\u003eESSTCCHVB\u003c\/a\u003e) \u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSAFAW80 (ESS-A-FAW80)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eEffective Coating Width\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e80 um (SS304)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eFilm Applicator Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAdjustable gap: 0-3 mm by rotating the two mechanical gauges\u003c\/li\u003e\n\u003cli\u003eMaterial: SS304\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eNote\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIt is an accessory for mini tape casting coater (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esstcchvb?variant=47491696754918\"\u003eESSTCCHVB\u003c\/a\u003e) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL110 * W35 * H55 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~0.35 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0272884217301475\"\u003eJ. Ko, et al., Thin cathode for thermal batteries using a tape-casting process, Ceramic International, 2017, 43, 5789-5793\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.4c18516\"\u003eH. Zhao, et al., Tape-Casting Fabrication Techniques for Garnet-Based Membranes in Solid-State Lithium-Metal Batteries: A Comprehensive Review, ACS Appl. Mater. Interfaces 2024, 16, 50, 68772–68793\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47492067393766,"sku":"ESSAFAW80","price":499.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCHVB_03.png?v=1774772711"},{"product_id":"essmtccihcvb","title":"ECS-SS Multifunctional Tape Casting Coater (Doctor Blade, Slot Die, and Wire Rod) with Infrared Heating Cover (120℃) and Vacuum Bed (L230*W120 mm), ESSMTCCIHCVB","description":"\u003cp\u003eFor lab-scale tape casting (also known as doctor blade coating), a tape casting coater with an infrared (IR) heating cover and vacuum bed provides a dual-advantage: the vacuum bed ensures the substrate stays perfectly flat during the stroke, while the IR cover enables rapid, uniform drying from the surface down. This is particularly effective for thick electrodes or ceramic tapes where \"skinning\" (trapped solvent under a dried surface layer) is a common defect\u003cspan style=\"font-size: 0.875rem;\"\u003e.\u003c\/span\u003e\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSMTCCIHCVB (ESS-MTCCIHCVB)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 1300 W \u003c\/li\u003e\n\u003cli\u003eAC110V can be customized upon request or equipped with a 2000W transformer.  \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eCoating Area\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe whole vacuum bed area is L230*W120mm, which enable the effective coating area is L220mm * W100 mm (depends on the film applicator is used).  \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoating Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e1-30 mm\/s\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eHeating Temperature \u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIR heating cover: Max. 120 ℃ (single-point control)\u003c\/li\u003e\n\u003cli\u003eResistance heating bottom: Max. 120 ℃ (single-point control)\u003c\/li\u003e\n\u003cli\u003eRealizing the simultaneous heating at the top and bottom. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eFilm Applicator (\u003cspan style=\"color: rgb(253, 8, 8);\"\u003eOptional\u003c\/span\u003e)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 1\u003c\/strong\u003e: Four Side Film Applicator with Fixed Gap\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            The standard one (effective coating width of 80mm) has four-side\u003c\/p\u003e\n\u003cp\u003e            gap of 100 um, 150 um, 200 um, and 250 um. Other options can\u003c\/p\u003e\n\u003cp\u003e            be found here (\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafsfafg?variant=47491848863974\"\u003eESSAFSFAFG\u003c\/a\u003e).\u003c\/p\u003e\n\u003cp\u003e            \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCHVB_02_100x100.png?v=1774764406\" alt=\"\" style=\"float: none;\" width=\"86\" height=\"86\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 2\u003c\/strong\u003e: Standard Film Applicator with Adjustable Gap, \u003ca href=\"https:\/\/echemsupplies.com\/products\/essafaw80?variant=47492067393766\"\u003eESSAFAW80\u003c\/a\u003e\u003cbr\u003e\n\u003cdiv style=\"text-align: left;\"\u003eThe standard coating width is 100 mm and adjustable gap is 0-3 mm (resolution: 5 um).  \u003c\/div\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafaw80?variant=47492067393766\"\u003e\u003cimg height=\"91\" width=\"91\" style=\"margin-bottom: 16px; float: none;\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCHVB_03_100x100.png?v=1774765217\"\u003e\u003c\/a\u003e\u003c\/div\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 3\u003c\/strong\u003e: Hybrid Fim Applicator (Doctor + Slot Die), \u003ca href=\"https:\/\/echemsupplies.com\/products\/essahfaw80?variant=47492745986278\"\u003eESSAHFAW80\u003c\/a\u003e  \u003cbr\u003e\n\u003cdiv style=\"text-align: left;\"\u003eThe standard coating width for the doctor blade is 100 mm and adjustable gap is 0-6 mm (resolution: 5 um)\u003c\/div\u003e\n\u003cdiv style=\"text-align: left;\"\u003eThe standard coating width for the slot die head is 80mm. The inside channel volume is 2 mL. The shims with thickness of 0.1, 0.2, 0.3, 0.4, 0.5 mm are included.  \u003c\/div\u003e\n \u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 4\u003c\/strong\u003e: Wire Rod (\u003ca href=\"https:\/\/echemsupplies.com\/products\/essawrw100?variant=47492793827558\"\u003eESSAWRW100\u003c\/a\u003e) \u003cbr\u003e\n\u003cdiv style=\"text-align: left;\"\u003eThe maximum coating width for the wire rod (D=10mm) is 100 mm. \u003cstrong\u003eThe wire groove diameter \u003c\/strong\u003e(determine the coating width, not the physical rod diameter):  6 um, 8 um, 10 um, 12 um, 15 um, 20 um, 25 um, 30 um, 40 um, 50 um, 60 um, 80 um, 100 um, 150 um, and 200 um are available.\u003ca href=\"https:\/\/echemsupplies.com\/products\/essawrw100?variant=47492793827558\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCIHCVB_03_160x160.png?v=1774808616\" alt=\"\" style=\"float: none;\"\u003e\u003c\/a\u003e\n\u003c\/div\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eVacuum Pump\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAn individual vacuum pump is included for sucking the substrate on vacuum bed \u003c\/li\u003e\n\u003cli\u003e8 mm O.D. tubing connection\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL470 * W420 * H360 mm for main coater (\u003cstrong\u003eglovebox-compatible\u003c\/strong\u003e)\u003c\/li\u003e\n\u003cli\u003eL200 * W170 * H150 mm for vacuum pump\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~42 kg (36 kg for coater and 6 kg for vacuum pump)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/onlinelibrary.wiley.com\/doi\/full\/10.1002\/ente.202000259\"\u003eR Diehm, et al., High-Speed Coating of Primer Layer for Li-Ion Battery Electrodes by Using Slot-Die Coating, Energy Technology, 2020, 8, 2000259\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/advanced.onlinelibrary.wiley.com\/doi\/abs\/10.1002\/admi.201600450\"\u003eM. S. Kim, et al., Multifunctional Separator Coatings for High-Performance \u003c\/a\u003e\u003cbr\u003e\u003ca href=\"https:\/\/advanced.onlinelibrary.wiley.com\/doi\/abs\/10.1002\/admi.201600450\"\u003eLithium–Sulfur Batteries, Adv. Mater. Interfaces, 2016, 3, 1600450\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Coater + Four-Side Film Applicator with Fix Gap","offer_id":47492678254822,"sku":"ESSMTCCIHCVBFS","price":3899.0,"currency_code":"USD","in_stock":true},{"title":"Coater + Standard Film Applicator with Adjustable Gap","offer_id":47492678287590,"sku":"ESSMTCCIHCVDS","price":3999.0,"currency_code":"USD","in_stock":true},{"title":"Coater + Slot Die","offer_id":47492727210214,"sku":"ESSMTCCIHCVBSD","price":4399.0,"currency_code":"USD","in_stock":true},{"title":"Coater + Wire Rod","offer_id":47492727242982,"sku":"ESSMTCCIHCVBWR","price":3999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMTCCIHCVB_main.png?v=1774809795"},{"product_id":"essahfaw80","title":"Hybrid Film Applicator (Doctor Blade + Slot Die) for Multifunctional Tape Casting Coater, ESSAHFA","description":"\u003cp\u003eA hybrid applicator with doctor blade and slot die head, which is the ideal solution for various coating scenarios. These tools allow you to use a doctor blade for high-viscosity \"batch\" slurries while offering a slot-die head for low-viscosity, precision-metered coatings.\u003c\/p\u003e\n\u003cp\u003eThe hybrid film applicator with adjustable gap (0-4 mm) is designed as accessories for multifunctional tap casting coaters, such as \u003ca href=\"https:\/\/echemsupplies.com\/products\/essmtccihcvb?variant=47492678254822\"\u003eESSMTCCIHCVB\u003c\/a\u003e \u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSAHFA (ESS-A-HFA)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eEffective Coating Width\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. coating width: 50, 80 mm, 100 mm, 150 mm, 200mm, 250mm, 300 mm, and 500 mm.\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eFilm Applicator Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAdjustable gap: 0-6 mm by rotating the two mechanical or digital gauges\u003c\/li\u003e\n\u003cli\u003eMaterial: SS304 (SS316 can be supplied upon request)\u003c\/li\u003e\n\u003cli\u003eThe mechanical micrometer is included. It will charge $300 more when upgrade from mechanical gauge to digital one.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0272884217301475\"\u003eJ. Ko, et al., Thin cathode for thermal batteries using a tape-casting process, Ceramic International, 2017, 43, 5789-5793\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.4c18516\"\u003eH. Zhao, et al., Tape-Casting Fabrication Techniques for Garnet-Based Membranes in Solid-State Lithium-Metal Batteries: A Comprehensive Review, ACS Appl. Mater. Interfaces 2024, 16, 50, 68772–68793\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Slot Die (50 mm) + Doctor Blade (100 mm)","offer_id":47501068435686,"sku":"ESSAHFASD50","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Slot Die (80 mm) + Doctor Blade (100 mm)","offer_id":47501068468454,"sku":"ESSAHFASD80","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Slot Die (100 mm) + Doctor Blade (150 mm)","offer_id":47501068501222,"sku":"ESSAHFASD100","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Slot Die (150 mm) + Doctor Blade (250 mm)","offer_id":47501068533990,"sku":"ESSAHFASD150","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Slot Die (200 mm) + Doctor Blade (250 mm)","offer_id":47501068566758,"sku":"ESSAHFASD200","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Slot Die (250 mm) + Doctor Blade (300 mm)","offer_id":47501068599526,"sku":"ESSAHFASD250","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Slot Die (300 mm) + Doctor Blade (350 mm)","offer_id":47501068632294,"sku":"ESSAHFASD300","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Slot Die (500 mm) + Doctor Blade (550 mm)","offer_id":47520286638310,"sku":"ESSAHFASD500","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSAHFA_main.png?v=1776022370"},{"product_id":"essawrw100","title":"Wire Rod (W=100 mm, D=10 mm) for Multifunctional Tape Casting Coater (ESSMTCCIHCVB), ESSAWRW100","description":"\u003cp\u003eWire Rod (or Mayer Rod) is a popular alternative to the doctor blade, especially when you need to coat thin, high-uniformity films on flexible substrates like battery foils or membranes. While a doctor blade relies on a mechanical gap, the wire rod uses the grooves between tightly wound stainless steel wires to meter the amount of slurry that passes through.\u003c\/p\u003e\n\u003cp\u003eThe wire rod with coating width of 100 mm is specially designed as accessories for the multifunctional tap casting coater (\u003ca href=\"https:\/\/echemsupplies.com\/products\/essmtccihcvb?variant=47492678254822\"\u003eESSMTCCIHCVB\u003c\/a\u003e) \u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSAWRW100 (ESS-A-WRW100)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eEffective Coating Width\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eWire Rod: 100 um, \u003c\/li\u003e\n\u003cli\u003eDiameter: 10 mm\u003c\/li\u003e\n\u003cli\u003eSS304 material (SS316 can be supplied upon request) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eWire Groove Sizes\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e6 um, 8 um, 10 um, 12 um, 15 um, 20 um, 25 um, 30 um, 40 um, 50 um, 60 um, 80 um, 100 um, 150 um, and 200 um\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eNote\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIt is an accessory for the multifunctional tape casting coater (\u003ca href=\"https:\/\/echemsupplies.com\/products\/essmtccihcvb?variant=47492678254822\"\u003eESSMTCCIHCVB\u003c\/a\u003e) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775307026584\"\u003eA. M. Kannan, et al., Wire rod coating process of gas diffusion layers fabrication for proton exchange membrane fuel cells, J. Power Sources, 2008, 178, 231-237\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.9b15866\"\u003eL. Zeng, et al., Integrated Paper-Based Flexible Li-Ion Batteries Made by a Rod Coating Method, ACS Appl. Mater. Interfaces 2019, 11, 50, 46776–46782\u003c\/a\u003e\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"6 um","offer_id":47492793827558,"sku":"ESSAWRW100G6","price":199.0,"currency_code":"USD","in_stock":true},{"title":"8 um","offer_id":47492793860326,"sku":"ESSAWRW100G8","price":199.0,"currency_code":"USD","in_stock":true},{"title":"10 um","offer_id":47492793893094,"sku":"ESSAWRW100G10","price":199.0,"currency_code":"USD","in_stock":true},{"title":"12 um","offer_id":47492793925862,"sku":"ESSAWRW100G12","price":199.0,"currency_code":"USD","in_stock":true},{"title":"15 um","offer_id":47492793958630,"sku":"ESSAWRW100G15","price":199.0,"currency_code":"USD","in_stock":true},{"title":"20 um","offer_id":47492793991398,"sku":"ESSAWRW100G20","price":199.0,"currency_code":"USD","in_stock":true},{"title":"25 um","offer_id":47492794024166,"sku":"ESSAWRW100G25","price":199.0,"currency_code":"USD","in_stock":true},{"title":"30 um","offer_id":47492794056934,"sku":"ESSAWRW100G30","price":199.0,"currency_code":"USD","in_stock":true},{"title":"40 um","offer_id":47492794089702,"sku":"ESSAWRW100G40","price":199.0,"currency_code":"USD","in_stock":true},{"title":"50 um","offer_id":47492794122470,"sku":"ESSAWRW100G50","price":199.0,"currency_code":"USD","in_stock":true},{"title":"60 um","offer_id":47492794155238,"sku":"ESSAWRW100G60","price":199.0,"currency_code":"USD","in_stock":true},{"title":"80 um","offer_id":47492794188006,"sku":"ESSAWRW100G80","price":199.0,"currency_code":"USD","in_stock":true},{"title":"100 um","offer_id":47492794220774,"sku":"ESSAWRW100G100","price":199.0,"currency_code":"USD","in_stock":true},{"title":"150 um","offer_id":47492794253542,"sku":"ESSAWRW100G150","price":199.0,"currency_code":"USD","in_stock":true},{"title":"200 um","offer_id":47492794286310,"sku":"ESSAWRW100G200","price":199.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMTCCIHCVB_03.png?v=1774809772"},{"product_id":"esmtccihcvb","title":"ECS-SM Tape Casting Coater with Infrared Heating Cover (120℃) and Vacuum Bed (L270*W200 mm), ESMTCCIHCVB","description":"\u003cp\u003eFor lab-scale tape casting (also known as doctor blade coating), a tape casting coater with an infrared (IR) heating cover and vacuum bed provides a dual-advantage: the vacuum bed ensures the substrate stays perfectly flat during the stroke, while the IR cover enables rapid, uniform drying from the surface down. This is particularly effective for thick electrodes or ceramic tapes where \"skinning\" (trapped solvent under a dried surface layer) is a common defect\u003cspan style=\"font-size: 0.875rem;\"\u003e.\u003c\/span\u003e\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESMTCCIHCVB (ESM-TCCIHCVB)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 2200 W \u003c\/li\u003e\n\u003cli\u003eAC110V can be customized upon request or equipped with a 3000W transformer.  \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eCoating Area\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe whole vacuum bed area is L300*W200mm, which enable the effective coating area is L270mm * W150 mm (depends on the film applicator is used).  \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoating Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e20-120 mm\/s\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eHeating Temperature \u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIR heating cover: Max. 120 ℃ (single-point control)\u003c\/li\u003e\n\u003cli\u003eNo resistance heating at bottom, which is good for cooling process for double-side coating (after one side coating)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eFilm Applicator\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eFilm Applicator with an Adjustable Width, \u003ca href=\"https:\/\/echemsupplies.com\/products\/esmafaacw?variant=47492852416742\"\u003eESMAFAACW\u003c\/a\u003e\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe maximum coating width is 150 mm, and adjustable coating width can be realized by moving the central plate. \u003c\/li\u003e\n\u003cli\u003eAdjustable gap: 0-3 mm (mechanical gauge, 10 um resolution). The digital gauge can be upgraded upon request. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003ca href=\"https:\/\/echemsupplies.com\/products\/esmafaacw?variant=47492852416742\"\u003e\u003cimg style=\"float: none;\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMTCCIHCVB_02_100x100.png?v=1774820283\"\u003e\u003c\/a\u003e\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafaw80?variant=47492067393766\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eVacuum Pump\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAn vacuum pump is built-in for sucking the substrate on vacuum bed \u003c\/li\u003e\n\u003cli\u003eVacuum level: -84 KPa, Max. flow rate: 30 L\/min, 120 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL670 * W370 * H370 mm for main coater (\u003cstrong\u003eglovebox-compatible\u003c\/strong\u003e)\u003c\/li\u003e\n\u003cli\u003eL540 * W260 * H430 mm for control box\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~100 kg (70 kg for coater and 30 kg for control box)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/advanced.onlinelibrary.wiley.com\/doi\/abs\/10.1002\/admi.201600450\"\u003eM. S. Kim, et al., Multifunctional Separator Coatings for High-Performance \u003c\/a\u003e\u003cbr\u003e\u003ca href=\"https:\/\/advanced.onlinelibrary.wiley.com\/doi\/abs\/10.1002\/admi.201600450\"\u003eLithium–Sulfur Batteries, Adv. Mater. Interfaces, 2016, 3, 1600450\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47492825940198,"sku":"ESMTCCIHCVB","price":4999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMTCCIHCVB_main.png?v=1774819591"},{"product_id":"esmafaacw","title":"Film Applicator with Adjustable Coating Width (0-150 mm) for Tape Casting Coater (ESMTCCIHCVB), ESMAFAACW","description":"\u003cp\u003eThe adjustable micrometer film applicator is the standard choice for tape casting coaters. Unlike fixed-gap versions, these allow you to fine-tune the gate height in 10-micron increments, which is essential when accounting for slurry shrinkage or when trying to hit a very specific dry-film target.\u003c\/p\u003e\n\u003cp\u003eThe film applicator with adjustable width (0-150 mm) is specially designed as accessories for medium-size tap casting coater (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esmtccihcvb?variant=47492825940198\"\u003eESMTCCIHCVB\u003c\/a\u003e) \u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESMAFAACW (ESM-A-FAACW)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eEffective Coating Width\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0-150 um, adjustable\u003c\/li\u003e\n\u003cli\u003eAluminum 6061 material. The light weight avoids the scratching issue and tearing the thin current collector for coating. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eFilm Applicator Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAdjustable gap: 0-3 mm by rotating the two mechanical gauges (upgrade version digital gauge can be supplied upon request)\u003c\/li\u003e\n\u003cli\u003eMaterial: SS304\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eNote\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIt is an accessory for mini tape casting coater (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esmtccihcvb?variant=47492825940198\"\u003eESMTCCIHCVB\u003c\/a\u003e) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL180 * W80 * H85 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~0.6 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0272884217301475\"\u003eJ. Ko, et al., Thin cathode for thermal batteries using a tape-casting process, Ceramic International, 2017, 43, 5789-5793\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.4c18516\"\u003eH. Zhao, et al., Tape-Casting Fabrication Techniques for Garnet-Based Membranes in Solid-State Lithium-Metal Batteries: A Comprehensive Review, ACS Appl. Mater. Interfaces 2024, 16, 50, 68772–68793\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47492852416742,"sku":"ESMAFAACW","price":499.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMTCCIHCVB_02.png?v=1774828337"},{"product_id":"esmmtcchvb","title":"ECS-SM Multifunctional Tape Casting Coater (Doctor Blade + Wire Rod + Slot Die) with Heated Vacuum Bed (L200*W200 mm, 160°C), ESMMTCCHVB","description":"\u003cp\u003eA 3-in-1 (multifunctional) tape casting coater is designed to support doctor blade, wire rod, and slot die coating methods on a single machine. This versatility is perfect for labs that need to switch between high-viscosity battery pastes and ultra-thin, low-viscosity functional coatings.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESMMTCCHVB (ESM-MTCCHVB)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 1000 W \u003c\/li\u003e\n\u003cli\u003eAC110V can be customized upon request or equipped with a 1500W transformer.  \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eCoating Area\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe vacuum bed supports a coating area of L200*W200mm.\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoating Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0-70 mm\/s (adjustable)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eBottom Resistance Heating\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eBottom Heating Temperature: Max. 160 ℃ (single-point control)\u003c\/li\u003e\n\u003cli\u003eSmall vacuum holes: φ3 mm\u003c\/li\u003e\n\u003cli\u003eSurface Flatness: ≤5um\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eFilm Applicator (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional)\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e(1) Film Applicator with an Adjustable Width, \u003ca href=\"https:\/\/echemsupplies.com\/products\/esmafaacw?variant=47492852416742\"\u003eESMAFAACW\u003c\/a\u003e\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe maximum coating width is 150 mm, and adjustable coating width can be realized by moving the central plate. \u003c\/li\u003e\n\u003cli\u003eAdjustable gap: 0-3 mm (mechanical gauge, 10 um resolution). The digital gauge can be upgraded upon request. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003ca href=\"https:\/\/echemsupplies.com\/products\/esmafaacw?variant=47492852416742\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMTCCIHCVB_02_100x100.png?v=1774820283\" style=\"margin-bottom: 16px; float: none;\" width=\"84\" height=\"84\"\u003e\u003c\/a\u003e\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafaw80?variant=47492067393766\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cspan\u003e(2) Wire Rod (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esmawrw200?variant=47492903174374\"\u003eESMAWRW200\u003c\/a\u003e\u003c\/span\u003e\u003cspan\u003e) \u003c\/span\u003e\u003cbr\u003e\n\u003cdiv\u003eThe maximum coating width for the wire rod (D=10mm) is 200 mm (other coating widths also can be supplied upon request).\u003cspan\u003e \u003c\/span\u003e\n\u003c\/div\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cdiv\u003e\n\u003cspan\u003e\u003c\/span\u003e\u003cstrong\u003eThe wire groove diameter\u003cspan\u003e \u003c\/span\u003e\u003c\/strong\u003e(determine the coating width, not the physical rod diameter):  6 um, 8 um, 10 um, 12 um, 15 um, 20 um, 25 um, 30 um, 40 um, 50 um, 60 um, 80 um, 100 um, 150 um, and 200 um are available. Only \u003c\/div\u003e\n\u003c\/li\u003e\n\u003cli\u003eTheoretically the dry coating thickness T = 0.5 * (wire groove diameter) * (transfer coefficient) * (solid-state content); Normally the transfer coefficient is in 0.5-0.7 and we will choose 0.6 as a typical value. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003ca href=\"https:\/\/echemsupplies.com\/products\/esmawrw200?variant=47492903174374\"\u003e\u003cimg style=\"float: none;\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMTCCDWHVB_02_100x100.png?v=1774827354\" width=\"77\" height=\"77\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cspan\u003e(3) Slot Die (\u003ca href=\"https:\/\/echemsupplies.com\/products\/essahfaw80?variant=47501068566758\"\u003eESSAHFASD200\u003c\/a\u003e)\u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003e           The maximum slot die coating width is 200 mm. An economic syringe pump (\u003ca href=\"https:\/\/echemsupplies.com\/products\/easdcepsp?variant=47501234307302\"\u003eEASDCEPSP\u003c\/a\u003e) can be used as the slurry feeder. \u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003e           \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSAHFA_main_100x100.png?v=1776022370\" style=\"margin-bottom: 16px; float: none;\"\u003e    \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCEPSP_main_100x100.png?v=1781726902\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eVacuum Pump\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAn vacuum pump is externally connected for sucking the substrate on vacuum bed \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL500 * W320 * H240 mm for main coater (\u003cstrong\u003eglovebox-compatible\u003c\/strong\u003e)\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~40 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/advanced.onlinelibrary.wiley.com\/doi\/abs\/10.1002\/admi.201600450\"\u003eM. S. Kim, et al., Multifunctional Separator Coatings for High-Performance \u003c\/a\u003e\u003cbr\u003e\u003ca href=\"https:\/\/advanced.onlinelibrary.wiley.com\/doi\/abs\/10.1002\/admi.201600450\"\u003eLithium–Sulfur Batteries, Adv. Mater. Interfaces, 2016, 3, 1600450\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Doctor Blade","offer_id":47492927422694,"sku":"ESMMTCCHVBDB","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Wire Rod","offer_id":47492927455462,"sku":"ESMMTCCHVBWR","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Doctor Blade+ Wire Rod","offer_id":47492927520998,"sku":"ESMMTCCHVBDBWR","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Doctor Blade + Wire Rod + Slot Die","offer_id":47899143274726,"sku":"ESMMTCCHVBDBWRSD","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMTCCDWHVB_03.png?v=1774828337"},{"product_id":"esmawrw200","title":"Wire Rod (W=200 mm, D=10 mm) for Multifunctional Tape Casting Coater (ESMTCCDWHVB), ESMAWRW200","description":"\u003cp\u003eWire Rod (or Mayer Rod) is a popular alternative to the doctor blade, especially when you need to coat thin, high-uniformity films on flexible substrates like battery foils or membranes. While a doctor blade relies on a mechanical gap, the wire rod uses the grooves between tightly wound stainless steel wires to meter the amount of slurry that passes through.\u003c\/p\u003e\n\u003cp\u003eThe wire rod with coating width of 200 mm is specially designed as accessories for the multifunctional tap casting coater (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esmmtcchvb?variant=47492927422694\"\u003eESMMTCCHVB\u003c\/a\u003e) \u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESMAWRW200 (ESM-A-WRW200)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eEffective Coating Width\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eWire Rod: 200 um, \u003c\/li\u003e\n\u003cli\u003eDiameter: 10 mm\u003c\/li\u003e\n\u003cli\u003eSS304 material (SS316 can be supplied upon request) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eWire Groove Sizes\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e6 um, 8 um, 10 um, 12 um, 15 um, 20 um, 25 um, 30 um, 40 um, 50 um, 60 um, 80 um, 100 um, 150 um, and 200 um\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eNote\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIt is an accessory for the multifunctional tape casting coater (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esmmtcchvb?variant=47492927422694\"\u003eESMMTCCHVB\u003c\/a\u003e) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775307026584\"\u003eA. M. Kannan, et al., Wire rod coating process of gas diffusion layers fabrication for proton exchange membrane fuel cells, J. Power Sources, 2008, 178, 231-237\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.9b15866\"\u003eL. Zeng, et al., Integrated Paper-Based Flexible Li-Ion Batteries Made by a Rod Coating Method, ACS Appl. Mater. Interfaces 2019, 11, 50, 46776–46782\u003c\/a\u003e\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"6 um","offer_id":47492903174374,"sku":"ESMAWRW200G6","price":249.0,"currency_code":"USD","in_stock":true},{"title":"8 um","offer_id":47492903207142,"sku":"ESMAWRW200G8","price":249.0,"currency_code":"USD","in_stock":true},{"title":"10 um","offer_id":47492903239910,"sku":"ESMAWRW200G10","price":249.0,"currency_code":"USD","in_stock":true},{"title":"12 um","offer_id":47492903272678,"sku":"ESMAWRW200G12","price":249.0,"currency_code":"USD","in_stock":true},{"title":"15 um","offer_id":47492903305446,"sku":"ESMAWRW200G15","price":249.0,"currency_code":"USD","in_stock":true},{"title":"20 um","offer_id":47492903338214,"sku":"ESMAWRW200G20","price":249.0,"currency_code":"USD","in_stock":true},{"title":"25 um","offer_id":47492903370982,"sku":"ESMAWRW200G25","price":249.0,"currency_code":"USD","in_stock":true},{"title":"30 um","offer_id":47492903403750,"sku":"ESMAWRW200G30","price":249.0,"currency_code":"USD","in_stock":true},{"title":"40 um","offer_id":47492903436518,"sku":"ESMAWRW200G40","price":249.0,"currency_code":"USD","in_stock":true},{"title":"50 um","offer_id":47492903469286,"sku":"ESMAWRW200G50","price":249.0,"currency_code":"USD","in_stock":true},{"title":"60 um","offer_id":47492903502054,"sku":"ESMAWRW200G60","price":249.0,"currency_code":"USD","in_stock":true},{"title":"80 um","offer_id":47492903534822,"sku":"ESMAWRW200G80","price":249.0,"currency_code":"USD","in_stock":true},{"title":"100 um","offer_id":47492903567590,"sku":"ESMAWRW200G100","price":249.0,"currency_code":"USD","in_stock":true},{"title":"150 um","offer_id":47492903600358,"sku":"ESMAWRW200G150","price":249.0,"currency_code":"USD","in_stock":true},{"title":"200 um","offer_id":47492903633126,"sku":"ESMAWRW200G200","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMTCCDWHVB_02.png?v=1774827923"},{"product_id":"esssdchvb","title":"ECS-SS Slot Die Coater with Heating Vacuum Bed (L150*W130 mm, 120℃), ESSSDCHVB","description":"\u003cp\u003eFor high-precision laboratory coating, a slot-die coater paired with a heated vacuum bed offers the most advanced control over film uniformity and drying kinetics. Unlike a doctor blade, a slot-die head is a closed system, which prevents solvent evaporation during the process and allows for a \"pre-metered\" coating where the thickness is determined by the pump's flow rate rather than a mechanical gap.\u003c\/p\u003e\n\u003cp\u003eThe key advantages for slot die coating: (1) \u003cstrong\u003eZero-Waste Coating\u003c\/strong\u003e: The closed-head design of a slot-die ensures that almost 100% of your slurry is deposited onto the substrate, which is vital when working with expensive materials like specialized catalysts or solid-state electrolytes. (2) \u003cstrong\u003ePrecision Drying\u003c\/strong\u003e: The vacuum bed prevents the substrate from warping under the heat of the IR or convection dryer, maintaining a perfectly flat plane for the slot-die head to glide over (typically at a height of 10-100µm). (3) \u003cstrong\u003eScalability\u003c\/strong\u003e: Because slot-die coating is a flow-rate-dependent process, the parameters you develop on these lab-scale heated beds can be directly translated to industrial production lines.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSSDCHVB (ESS-SDCHVB)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, single phase, 50\/60Hz, 280 W \u003c\/li\u003e\n\u003cli\u003eA DC24V converter is included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eCoating Area\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe whole vacuum bed area is L150*W130mm, which enable the effective coating area of L100mm * W100 mm with included slot die head\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoating Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.05-20 mm\/s\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eBottom Heating Temperature \u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 120 ℃ (single-point control)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eSlot Die Head\u003c\/p\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSSDCHVB_02_100x100.png?v=1774847446\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/div\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA slot die head with a 100 mm width is included\u003c\/li\u003e\n\u003cli\u003eFour pieces of shims, such as 0.1, 0.2, 0.3, 0.4 mm are included\u003c\/li\u003e\n\u003cli\u003eThe coating width within 100 mm can be realized by customized the opening mouth of the shims. \u003c\/li\u003e\n\u003cli\u003eInside channel volume is around 2.6 mL\u003c\/li\u003e\n\u003cli\u003eThe gap between the slot die tip and vacuum bed can be adjusted in 0-5 mm by rotating the digital gauges (resolution:1 um)\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafaw80?variant=47492067393766\"\u003e\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSlurry Feeding Pump\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eOne 20 mL stainless steel syringe with a plastic plunger is included., which can be mounted at the side. A large syringe (eg: 60 mL) can be supplied upon request). \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSSDCHVB_03_100x100.png?v=1774848495\" style=\"float: none;\"\u003e \u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry feeding speed: 0.05-5 mL\/s \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eVacuum Pump\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA small vacuum pump is built-in for sucking the coating substrates \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL450 * W360 * H350 mm (glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~20 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/onlinelibrary.wiley.com\/doi\/full\/10.1002\/ente.202200684\"\u003eS. Spiegel, et al., Thin cathode for thermal batteries using a tape-casting proces, Energy Technology, 2023, 11, 2200684\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0255270112001997\"\u003eM. Schmitt, et al., Slot-die processing of lithium-ion battery electrodes—Coating window characterization, Chemical Engineering and Processing: Process Intensification, 2013, 68, 32-37\u003c\/a\u003e\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47493680070886,"sku":"ESSSDCHVB","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSSDCHVB_main.png?v=1774847432"},{"product_id":"esmsdchvb","title":"ECS-SM Slot Die Coater with Heating Vacuum Bed (L360*W250 mm, 100℃), ESMSDCHVB","description":"\u003cp\u003eFor high-precision laboratory coating, a slot-die coater paired with a heated vacuum bed offers the most advanced control over film uniformity and drying kinetics. Unlike a doctor blade, a slot-die head is a closed system, which prevents solvent evaporation during the process and allows for a \"pre-metered\" coating where the thickness is determined by the pump's flow rate rather than a mechanical gap.\u003c\/p\u003e\n\u003cp\u003eThe key advantages for slot die coating: (1) \u003cstrong\u003eZero-Waste Coating\u003c\/strong\u003e: The closed-head design of a slot-die ensures that almost 100% of your slurry is deposited onto the substrate, which is vital when working with expensive materials like specialized catalysts or solid-state electrolytes. (2) \u003cstrong\u003ePrecision Drying\u003c\/strong\u003e: The vacuum bed prevents the substrate from warping under the heat of the IR or convection dryer, maintaining a perfectly flat plane for the slot-die head to glide over (typically at a height of 10-100µm). (3) \u003cstrong\u003eScalability\u003c\/strong\u003e: Because slot-die coating is a flow-rate-dependent process, the parameters you develop on these lab-scale heated beds can be directly translated to industrial production lines.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESMSDCHVB (ESM-SDCHVB)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, single phase, 50\/60Hz, 500 W \u003c\/li\u003e\n\u003cli\u003eA DC24V converter is included\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eCoating Area\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe whole vacuum bed area is L360*W250mm, which enable the effective coating area of L300mm * W200 mm with included slot die head\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoating Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.05-20 mm\/s\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eBottom Heating Temperature \u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 100 ℃ (single-point control)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eSlot Die Head\u003c\/p\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSSDCHVB_02_100x100.png?v=1774847446\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/div\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA slot die head with a 200 mm width is included\u003c\/li\u003e\n\u003cli\u003eFour pieces of shims, such as 0.1, 0.2, 0.3, 0.4 mm are included\u003c\/li\u003e\n\u003cli\u003eThe coating width within 200 mm can be realized by customized the opening mouth of the shims. \u003c\/li\u003e\n\u003cli\u003eInside channel volume is around 8.0 mL\u003c\/li\u003e\n\u003cli\u003eThe gap between the slot die tip and vacuum bed can be adjusted in 0-5 mm by rotating the digital gauges (resolution:1 um)\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafaw80?variant=47492067393766\"\u003e\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSlurry Feeding Pump\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eOne 60 mL stainless steel syringe with a plastic plunger is included., which can be mounted at the side. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMSDCHVB_02_100x100.png?v=1774853240\" style=\"float: none;\"\u003e \u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry feeding speed: 0.1-1.5 mm\/s \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eVacuum Pump\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA small vacuum pump is built-in for sucking the coating substrates \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eUpgrade Version (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional\u003c\/span\u003e)\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eFor melting-slot die extrusion process, such as polymer-based solid-state electrolyte, the feed syringe and slot die head with heating jacket (100 ℃) can be supplied.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMSDCHVB_03_160x160.png?v=1774854036\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL450 * W360 * H350 mm (glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~20 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/onlinelibrary.wiley.com\/doi\/full\/10.1002\/ente.202200684\"\u003eS. Spiegel, et al., Thin cathode for thermal batteries using a tape-casting process, Energy Technology, 2023, 11, 2200684\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0255270112001997\"\u003eM. Schmitt, et al., Slot-die processing of lithium-ion battery electrodes—Coating window characterization, Chemical Engineering and Processing: Process Intensification, 2013, 68, 32-37\u003c\/a\u003e\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47493742133478,"sku":"ESMSDCHVB","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMSDCHVB_main.png?v=1774853240"},{"product_id":"esmr2reficcc","title":"ECS-SM Lab-Scale Roll-to-Roll Electrode Fabrication with Integrated Coater, Calender, and Cutter, ESMR2REFICCC","description":"\u003cp\u003eFor lab-scale roll-to-roll (R2R) electrode fabrication, the process is typically divided into three primary stages: precision coating, densification (calendering), and final shaping (slitting\/cutting). Transitioning to R2R allows you to simulate industrial production while maintaining the flexibility of a research environment.\u003c\/p\u003e\n\u003cp\u003eThe lab-scale roll-to-roll electrode fabrication unit integrated the coating, rolling press, and die cutting to continuously obtain round electrode disk and electrode sheet for coin cell and pouch cell, respectively. \u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESMR2REFICCC (ESM-R2REF-ICCC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower Source\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 5500 W \u003c\/li\u003e\n\u003cli\u003eAC110V can be realized by using a high power transformer\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eGas Source\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.5-0.8 MPa for pneumatic operation \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoating Unit\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eGuiding Roller Width: 100 mm\u003c\/li\u003e\n\u003cli\u003eMax. substrate roll and coating width is 80 and 60 mm, respectively. A four-side film applicator is included. \u003c\/li\u003e\n\u003cli\u003eWeb Speed: 0.01-1.0 m\/min\u003c\/li\u003e\n\u003cli\u003eCoating Speed: 0.2 m\/min (based on graphite anode slurry, viscosity is 2000 cP, solid content is 45% and dry film thickness of 90 um)\u003c\/li\u003e\n\u003cli\u003eCoating thickness uniformity: ±3μm\u003c\/li\u003e\n\u003cli\u003eManual slurry loading. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDrying Unit\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eConvection heating mode, single chamber length: 0.5 m\u003c\/li\u003e\n\u003cli\u003eElectric heating with a power of 2400 W\u003c\/li\u003e\n\u003cli\u003eMax. heating temperature: 130℃ \u003c\/li\u003e\n\u003cli\u003eVentilation: centrifugal fan with air flow of 570 m3\/h. The outlet port size is 120 mm to connect a 5\" aluminum pipe.  \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eRolling Press Unit\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCold Calender with a size of Φ100 x L90mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eRoller hardness: ≥HRC55\u003c\/li\u003e\n\u003cli\u003eRolling gap: 0-1.5 mm, adjustable with mechanical gauge\u003c\/li\u003e\n\u003cli\u003eMax. rolling press force: 5 T (unchangeable)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eElectrode Cutting Unit\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eTraverse distance for cutting: Max. 16 mm \u003c\/li\u003e\n\u003cli\u003eFor coin cell, the cutting die is available in φ8～φ24mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eTension Control \u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e10-40 N\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eLoading Roll\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eWinding\/Unwinding Roll Diameter: Max. Ф250mm\u003c\/li\u003e\n\u003cli\u003eCardboard Size: I.D. 3\" \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL2000 * W750 * H850 mm (glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~500 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S2405829720301641\"\u003eD. L. Wood III, et al., Perspectives on the relationship between materials chemistry and roll-to-roll electrode manufacturing for high-energy lithium-ion batteries, Energy Storage Materials, 2020, 29, 254-265\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.nature.com\/articles\/s44359-024-00018-w\"\u003eR. Tao, et al., Advanced electrode processing for lithium-ion battery manufacturing, Nature Reviews Clean Technology, 2025, 1, 116–131\u003c\/a\u003e.\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47493881069798,"sku":"ESMR2REFICCC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMR2REFICCC_main.png?v=1774858221"},{"product_id":"erstcchvb","title":"ECS-RS Tape Casting Coater with Top\/Bottom Heating (130℃) and Vacuum Bed (L250*W150 mm), ERSTCCHVB","description":"\u003cp\u003eFor lab-scale tape casting (also known as doctor blade coating), the most effective systems combine a high-precision vacuum chuck to hold the substrate flat and an integrated heating element to control the drying process. These features are critical for producing uniform, crack-free films for battery electrodes, fuel cell membranes, or ceramic tapes.\u003c\/p\u003e\n\u003cp\u003eThe key selection criteria of an appropriate tape casting coater: (1) \u003cstrong\u003eVacuum Bed\u003c\/strong\u003e: Essential for keeping thin foils (like Copper or Aluminum) or polymer films from wrinkling during the coating stroke. (2) \u003cstrong\u003eHeating Method\u003c\/strong\u003e: Top heating (infrared or convection) dries the slurry surface first, while bottom heating (heated bed) transfers heat through the substrate. (3) \u003cstrong\u003eCoating Speed\u003c\/strong\u003e: Look for variable speed control (typically 0–100 mm\/s) to match the rheology of your specific slurry. (4) \u003cstrong\u003eDoctor Blade Compatibility\u003c\/strong\u003e: Most of these units are compatible with adjustable micrometer doctor blades or fixed-gap film applicators.\u003c\/p\u003e\n\u003ctable style=\"height: 1412.6px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eERSTCCHVB (ERS-TCCHVB)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC110 or 220V±10%, single phase, 50\/60Hz, 650 W\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 106.4px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 106.4px;\"\u003e\u003cem\u003eCoating Area\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 106.4px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe aluminum alloy vacuum bed area is L415*W200mm, which enable the effective coating area is L300mm * W150 mm (depends on the film applicator is used).  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance is 300 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003eCoating Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0-120 mm\/s\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 538.8px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 538.8px;\"\u003e\u003cem\u003eHeating Model \u0026amp; Temperature\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 538.8px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 150 ℃ (±1°C, single-point control)\u003c\/li\u003e\n\u003cli\u003eMax. heating rate: 10 °C\/min, resistance heating mechanism\u003c\/li\u003e\n\u003cli\u003eThere are three types of heating models:\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            (1) Top-Cover Heating\u003c\/p\u003e\n\u003cp\u003e                  \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSTCCHVB_02_100x100.png?v=1775014151\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cp\u003e            (2) Bottom Plate Heating\u003c\/p\u003e\n\u003cp\u003e             \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSTCCHVB_03_100x100.png?v=1775017282\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cp\u003e           (3) TOP Cover + Bottom Plate Heating\u003cbr\u003e              \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSTCCHVB_04_100x100.png?v=1775017619\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 414.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 414.6px;\"\u003e\n\u003cp\u003eFilm Applicator (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional, not included\u003c\/span\u003e)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 414.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 1\u003c\/strong\u003e: Four Side Film Applicator with Fixed Gap\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            The standard one (effective coating width of 80mm) has four-side\u003c\/p\u003e\n\u003cp\u003e            gap of 100 um, 150 um, 200 um, and 250 um. Other options can\u003c\/p\u003e\n\u003cp\u003e            be found here (\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafsfafg?variant=47491848863974\"\u003eESSAFSFAFG\u003c\/a\u003e).\u003c\/p\u003e\n\u003cp\u003e            \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCHVB_02_100x100.png?v=1774764406\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 2\u003c\/strong\u003e: Standard Film Applicator with Adjustable Gap (\u003ca href=\"https:\/\/echemsupplies.com\/products\/etccafa?variant=47500878053606\"\u003eETCCAFA\u003c\/a\u003e)\u003cbr\u003e\n\u003cdiv style=\"text-align: left;\"\u003eThe standard coating width of 50 ,100 or 150 mm can be used for this coater.  \u003c\/div\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\u003cimg style=\"margin-bottom: 16px; float: none;\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETCCAFA_main_100x100.png?v=1775016251\"\u003e\u003c\/div\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003eVacuum Pump\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA vacuum pump is built-in for operation\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 67.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 67.2px;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 67.2px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL500 * W350 * H320 mm (glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~40 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0272884217301475\"\u003eJ. Ko, et al., Thin cathode for thermal batteries using a tape-casting process, Ceramic International, 2017, 43, 5789-5793\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.4c18516\"\u003eH. Zhao, et al., Tape-Casting Fabrication Techniques for Garnet-Based Membranes in Solid-State Lithium-Metal Batteries: A Comprehensive Review, ACS Appl. Mater. Interfaces 2024, 16, 50, 68772–68793\u003c\/a\u003e. \u003c\/p\u003e","brand":"RSC","offers":[{"title":"Top-Cover Heating","offer_id":47500920127718,"sku":"ERSTCCTHVB","price":3599.0,"currency_code":"USD","in_stock":true},{"title":"Bottom-Plate Heating","offer_id":47500920160486,"sku":"ERSTCCBHVB","price":3599.0,"currency_code":"USD","in_stock":true},{"title":"Top Cover + Bottom Plate Heating","offer_id":47500920193254,"sku":"ERSTCCTBHVB","price":3999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSTCCHVB_02.png?v=1775014151"},{"product_id":"etccafa","title":"Film Applicator (Doctor Blade) with Adjustable Gap (0-5 mm) for Tape Casting Coater, ETCCAFA","description":"\u003cp\u003eThe adjustable micrometer film applicator is the standard choice for tape casting coaters. Unlike fixed-gap versions, these allow you to fine-tune the gate height in 10-micron increments, which is essential when accounting for slurry shrinkage or when trying to hit a very specific dry-film target.\u003c\/p\u003e\n\u003cp\u003eThe film applicator with various coating width can be used for different tap casting coaters. \u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eETCCAFA (ETCC-A-FA)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eEffective Coating Width\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e50-500 um (SS304)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eFilm Applicator Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAdjustable gap: 0-5 mm by rotating the two mechanical gauges\u003c\/li\u003e\n\u003cli\u003eMaterial: SS304\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0272884217301475\"\u003eJ. Ko, et al., Thin cathode for thermal batteries using a tape-casting process, Ceramic International, 2017, 43, 5789-5793\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.4c18516\"\u003eH. Zhao, et al., Tape-Casting Fabrication Techniques for Garnet-Based Membranes in Solid-State Lithium-Metal Batteries: A Comprehensive Review, ACS Appl. Mater. Interfaces 2024, 16, 50, 68772–68793\u003c\/a\u003e. \u003c\/p\u003e","brand":"TOB","offers":[{"title":"50 mm","offer_id":47500878053606,"sku":"ETCCAFAW50","price":399.0,"currency_code":"USD","in_stock":true},{"title":"100 mm","offer_id":47500878086374,"sku":"ETCCAFAW100","price":449.0,"currency_code":"USD","in_stock":true},{"title":"150 mm","offer_id":47500878119142,"sku":"ETCCAFAW150","price":499.0,"currency_code":"USD","in_stock":true},{"title":"200 mm","offer_id":47500878151910,"sku":"ETCCAFAW200","price":599.0,"currency_code":"USD","in_stock":true},{"title":"250 mm","offer_id":47500878184678,"sku":"ETCCAFAW250","price":699.0,"currency_code":"USD","in_stock":true},{"title":"300 mm","offer_id":47500878217446,"sku":"ETCCAFAW300","price":799.0,"currency_code":"USD","in_stock":true},{"title":"500 mm","offer_id":47520265273574,"sku":"ETCCAFAW500","price":2299.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETCCAFA_main.png?v=1775016251"},{"product_id":"etmtcchvb","title":"ECS-TM Economic Tape Casting Coater with Top\/Bottom Heating (130℃) and Vacuum Bed (L300*W250 mm), ETMTCCHVB","description":"\u003cp\u003eFor lab-scale tape casting (also known as doctor blade coating), the most effective systems combine a high-precision vacuum chuck to hold the substrate flat and an integrated heating element to control the drying process. These features are critical for producing uniform, crack-free films for battery electrodes, fuel cell membranes, or ceramic tapes.\u003c\/p\u003e\n\u003cp\u003eThe key selection criteria of an appropriate tape casting coater: (1) \u003cstrong\u003eVacuum Bed\u003c\/strong\u003e: Essential for keeping thin foils (like Copper or Aluminum) or polymer films from wrinkling during the coating stroke. (2) \u003cstrong\u003eHeating Method\u003c\/strong\u003e: Top heating (infrared or convection) dries the slurry surface first, while bottom heating (heated bed) transfers heat through the substrate. (3) \u003cstrong\u003eCoating Speed\u003c\/strong\u003e: Look for variable speed control (typically 0–100 mm\/s) to match the rheology of your specific slurry. (4) \u003cstrong\u003eDoctor Blade Compatibility\u003c\/strong\u003e: Most of these units are compatible with adjustable micrometer doctor blades or fixed-gap film applicators.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eETMTCCHVB (ETM-TCCHVB)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, single phase, 50\/60Hz, 1500 W\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eCoating Area\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe aluminum alloy vacuum bed area is L415*W300mm, which enable the effective coating area is L300mm * W250 mm (depends on the film applicator is used).  \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoating Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0-120 mm\/s\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eHeating Model \u0026amp; Temperature\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 130 ℃ (±1°C, single-point control)\u003c\/li\u003e\n\u003cli\u003eMax. heating rate: 10 °C\/min, resistance heating mechanism\u003c\/li\u003e\n\u003cli\u003eThere are three types of heating models:\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            (1) Top-Cover Heating (default is electric resistance heating, but \u003c\/p\u003e\n\u003cp\u003e                  IR heating is available upon request)\u003c\/p\u003e\n\u003cp\u003e                  \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSTCCHVB_02_100x100.png?v=1775014151\"\u003e\u003c\/p\u003e\n\u003cp\u003e            (2) Bottom Plate Heating\u003c\/p\u003e\n\u003cp\u003e             \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSTCCHVB_03_100x100.png?v=1775017282\"\u003e\u003c\/p\u003e\n\u003cp\u003e           (3) TOP Cover + Bottom Plate Heating\u003cbr\u003e              \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSTCCHVB_04_100x100.png?v=1775017619\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eFilm Applicator (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional, not included\u003c\/span\u003e)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 1\u003c\/strong\u003e: Standard Film Applicator with Adjustable Gap (\u003ca href=\"https:\/\/echemsupplies.com\/products\/etccafa?variant=47500878053606\"\u003eETCCAFA\u003c\/a\u003e). The recommended coating width is less than 250 mm. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETCCAFA_main_100x100.png?v=1775016251\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 2\u003c\/strong\u003e: Hybrid film applicator (slot die + doctor blade) \u003ca href=\"https:\/\/echemsupplies.com\/products\/essahfaw80?variant=47501068435686\"\u003eESSAHFA.\u003c\/a\u003e The recommend slot die coating width is less than 250 mm.  For slot die coating, the syringe pumps (\u003ca href=\"https:\/\/echemsupplies.com\/products\/easdcepsp?variant=47501234307302\"\u003eEASDCEPSP\u003c\/a\u003e or \u003ca href=\"https:\/\/echemsupplies.com\/products\/easdclssp?variant=47501457785062\"\u003eEASDCLSSP\u003c\/a\u003e can be considered) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e         \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMTCCIHCVB_06_100x100.png?v=1775022058\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eVacuum Pump\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA vacuum pump is built-in for operation \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL550 * W450 * H320 mm (glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~70 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0272884217301475\"\u003eJ. Ko, et al., Thin cathode for thermal batteries using a tape-casting process, Ceramic International, 2017, 43, 5789-5793\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.4c18516\"\u003eH. Zhao, et al., Tape-Casting Fabrication Techniques for Garnet-Based Membranes in Solid-State Lithium-Metal Batteries: A Comprehensive Review, ACS Appl. Mater. Interfaces 2024, 16, 50, 68772–68793\u003c\/a\u003e. \u003c\/p\u003e","brand":"TOB","offers":[{"title":"Top-Cover Heating","offer_id":47500948373734,"sku":"ETMTCCTHVB","price":4499.0,"currency_code":"USD","in_stock":true},{"title":"Bottom-Plate Heating","offer_id":47500948406502,"sku":"ETMTCCBHVB","price":4499.0,"currency_code":"USD","in_stock":true},{"title":"Top Cover + Bottom Plate Heating","offer_id":47500948439270,"sku":"ETMTCCTBHVB","price":4999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETMTCCHVB_main.png?v=1775024196"},{"product_id":"easdcepsp","title":"Economic Programmable Syringe Pump for Slot Die Coater, EASDCEPSP","description":"\u003cp\u003eFor high-precision slot-die coating, a high-pressure syringe pump is the standard delivery system. Unlike a doctor blade where thickness is controlled by a mechanical gap, slot-die coating is a pre-metered process—the wet film thickness is directly proportional to the pump's flow rate and inversely proportional to the coating speed.\u003c\/p\u003e\n\u003cp\u003eTo achieve a uniform, streak-free coating, the syringe pump should meet these technical criteria: (1) \u003cstrong\u003ePulse-Free Flow\u003c\/strong\u003e: The motor must have high micro-stepping resolution. Any \"pulsing\" in the flow will result in visible transverse \"ribbing\" or waves in your dried electrode. (2) \u003cstrong\u003eHigh Torque\/Linear Force\u003c\/strong\u003e: Battery and CDI slurries are often highly viscous (\"peanut butter\" consistency). Standard medical syringe pumps will often \"stall\" or \"slip.\" You need a laboratory-grade pump with at least 20–40 lbs (9–18 kg) of linear force. (3) \u003cstrong\u003eChemical Compatibility\u003c\/strong\u003e: The syringe itself should be stainless steel or glass with a PTFE-tipped plunger. Plastic syringes can swell or leach when used with solvents like NMP (N-Methyl-2-pyrrolidone).\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEASDCEPSP (E-A-SDC-EPSP)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan\u003eAC110-220V±10%, single phase, 50\/60Hz, ~1 W\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePump Pressure Version\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eStandard Pressure, 0.5-60 mL\u003c\/li\u003e\n\u003cli\u003eHigh Pressure, it will provide a double pump force. For example, regarding a 60 mL syringe, the standard pressure version will produce 30 psi, while the high-pressure version will provide 60 psi. The high-pressure version is suitable for high viscosity slurry conditions.  \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSyringe Sizes\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe standard size is 30 mL that is included with the syringe pump.\u003c\/li\u003e\n\u003cli\u003eOther syringe sizes within 0.5-60 mL, such as 0.5, 1, 3, 5, 10, 20, 60 mL are available upon request. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePumping Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e         Standard Pressure                   High Pressure \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCESP_01_160x160.png?v=1775029021\"\u003e       \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCESP_02_160x160.png?v=1775029039\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12541-020-00425-6\"\u003eH. Lee, et al., Design and Assembly of a Thin-Film-Based Micro Pump for a Micro-slot Die, International Journal of Precision Engineering and Manufacturing, 2020, 21, 2335–2344\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/aiche.onlinelibrary.wiley.com\/doi\/full\/10.1002\/aic.15268\"\u003eX. Ding, et al., A review of the operating limits in slot die coating processes, AICHE J., 2016, 62, 2508-2524\u003c\/a\u003e. \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"Scientific Instruments","offers":[{"title":"Standard Pressure","offer_id":47501234307302,"sku":"EASDCEPSPSP","price":399.0,"currency_code":"USD","in_stock":true},{"title":"High Pressure","offer_id":47501234340070,"sku":"EASDCEPSPHP","price":449.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCEPSP_main.png?v=1781726902"},{"product_id":"easdclssp","title":"Lab-Scale Syringe Pump for Slot Die Coater, EASDCLSSP","description":"\u003cp\u003eFor high-precision slot-die coating, a high-pressure syringe pump is the standard delivery system. Unlike a doctor blade where thickness is controlled by a mechanical gap, slot-die coating is a pre-metered process—the wet film thickness is directly proportional to the pump's flow rate and inversely proportional to the coating speed.\u003c\/p\u003e\n\u003cp\u003eTo achieve a uniform, streak-free coating, the syringe pump should meet these technical criteria: (1) \u003cstrong\u003ePulse-Free Flow\u003c\/strong\u003e: The motor must have high micro-stepping resolution. Any \"pulsing\" in the flow will result in visible transverse \"ribbing\" or waves in your dried electrode. (2) \u003cstrong\u003eHigh Torque\/Linear Force\u003c\/strong\u003e: Battery and CDI slurries are often highly viscous (\"peanut butter\" consistency). Standard medical syringe pumps will often \"stall\" or \"slip.\" You need a laboratory-grade pump with at least 20–40 lbs (9–18 kg) of linear force. (3) \u003cstrong\u003eChemical Compatibility\u003c\/strong\u003e: The syringe itself should be stainless steel or glass with a PTFE-tipped plunger. Plastic syringes can swell or leach when used with solvents like NMP (N-Methyl-2-pyrrolidone).\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEASDCLSSP (E-A-SDC-LSSP)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan\u003eAC110-220V±10%, single phase, 50\/60Hz, ~120 W\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSpeed Range\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e0.05-5 mm\/s \u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSyringe Sizes\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eStandard 20 mL, 30 mL, 50 mL syringes (PP) are included. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eTraverse Distance\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 100 mm (step motor)  \u003cspan style=\"font-size: 0.875rem;\"\u003e       \u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eConnection Tubing\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eTeflon Tubing, O.D. 3.2mm, I.D. 1.6mm \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL400×W200×H230mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e8 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12541-020-00425-6\"\u003eH. Lee, et al., Design and Assembly of a Thin-Film-Based Micro Pump for a Micro-slot Die, International Journal of Precision Engineering and Manufacturing, 2020, 21, 2335–2344\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/aiche.onlinelibrary.wiley.com\/doi\/full\/10.1002\/aic.15268\"\u003eX. Ding, et al., A review of the operating limits in slot die coating processes, AICHE J., 2016, 62, 2508-2524\u003c\/a\u003e. \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"TOB","offers":[{"title":"Default Title","offer_id":47501457785062,"sku":"EASDCLSSP","price":299.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCLSSP_main.png?v=1775030589"},{"product_id":"erltcchvb","title":"ECS-RL Tape Casting Coater with Top\/Bottom Heating (130℃) and Vacuum Bed (L800*W150 mm), ERLTCCHVB","description":"\u003cp\u003eFor lab-scale tape casting (also known as doctor blade coating), the most effective systems combine a high-precision vacuum chuck to hold the substrate flat and an integrated heating element to control the drying process. These features are critical for producing uniform, crack-free films for battery electrodes, fuel cell membranes, or ceramic tapes.\u003c\/p\u003e\n\u003cp\u003eThe key selection criteria of an appropriate tape casting coater: (1) \u003cstrong\u003eVacuum Bed\u003c\/strong\u003e: Essential for keeping thin foils (like Copper or Aluminum) or polymer films from wrinkling during the coating stroke. (2) \u003cstrong\u003eHeating Method\u003c\/strong\u003e: Top heating (infrared or convection) dries the slurry surface first, while bottom heating (heated bed) transfers heat through the substrate. (3) \u003cstrong\u003eCoating Speed\u003c\/strong\u003e: Look for variable speed control (typically 0–100 mm\/s) to match the rheology of your specific slurry. (4) \u003cstrong\u003eDoctor Blade Compatibility\u003c\/strong\u003e: Most of these units are compatible with adjustable micrometer doctor blades or fixed-gap film applicators.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eERLTCCHVB (ERL-TCCHVB)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, single phase, 50\/60Hz, 2000 W\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eCoating Area\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe aluminum alloy vacuum bed area is L900*W200mm, which enable the effective coating area is L800mm * W150 mm (depends on the film applicator is used).  \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoating Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0-200 mm\/s\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eHeating Model \u0026amp; Temperature\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 130 ℃ (±1°C, single-point control)\u003c\/li\u003e\n\u003cli\u003eMax. heating rate: 10 °C\/min, resistance heating mechanism\u003c\/li\u003e\n\u003cli\u003eThere are three types of heating models:\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            (1) Top-Cover Heating (default is electric resistance heating, but \u003c\/p\u003e\n\u003cp\u003e                  IR heating is available upon request)\u003c\/p\u003e\n\u003cp\u003e            (2) Bottom Plate Heating\u003c\/p\u003e\n\u003cp\u003e            (3) TOP Cover + Bottom Plate Heating\u003cbr\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eFilm Applicator (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional, not included\u003c\/span\u003e)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 1\u003c\/strong\u003e: \u003cspan\u003eFour Side Film Applicator with Fixed Gap (\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafsfafg?variant=47491848863974\"\u003eESSAFSFAFG\u003c\/a\u003e)\u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003e          \u003c\/span\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCHVB_02_100x100.png?v=1774771839\" alt=\"\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 2\u003c\/strong\u003e: Standard Film Applicator with Adjustable Gap (\u003ca href=\"https:\/\/echemsupplies.com\/products\/etccafa?variant=47500878053606\"\u003eETCCAFA\u003c\/a\u003e). The recommended doctor blade coating width is 50 mm, 100 mm, and 150 mm. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETCCAFA_main_100x100.png?v=1775016251\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 3\u003c\/strong\u003e: Hybrid film applicator (slot die + doctor blade) \u003ca href=\"https:\/\/echemsupplies.com\/products\/essahfaw80?variant=47501068435686\"\u003eESSAHFA.\u003c\/a\u003e The recommend slot die coating head is Slot Die (100 mm) + Doctor Blade (150 mm).  For slot die coating, the syringe pumps (\u003ca href=\"https:\/\/echemsupplies.com\/products\/easdcepsp?variant=47501234307302\"\u003eEASDCEPSP\u003c\/a\u003e or \u003ca href=\"https:\/\/echemsupplies.com\/products\/easdclssp?variant=47501457785062\"\u003eEASDCLSSP\u003c\/a\u003e can be considered) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e         \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMTCCIHCVB_06_100x100.png?v=1775022058\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eVacuum Pump\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA vacuum pump is externally connected for operation\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL550 * W450 * H320 mm (glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~70 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0272884217301475\"\u003eJ. Ko, et al., Thin cathode for thermal batteries using a tape-casting process, Ceramic International, 2017, 43, 5789-5793\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.4c18516\"\u003eH. Zhao, et al., Tape-Casting Fabrication Techniques for Garnet-Based Membranes in Solid-State Lithium-Metal Batteries: A Comprehensive Review, ACS Appl. Mater. Interfaces 2024, 16, 50, 68772–68793\u003c\/a\u003e. \u003c\/p\u003e","brand":"RSC","offers":[{"title":"Top-Cover Heating","offer_id":47502052819174,"sku":"ERLTCCTHVB","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Bottom-Plate Heating","offer_id":47502052851942,"sku":"ERLTCCBHVB","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Top Cover + Bottom Plate Heating","offer_id":47502052884710,"sku":"ERLTCCTBHVB","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETLTCCHVB_main.png?v=1775055391"},{"product_id":"eahtsfpsp8c","title":"Programmable Syringe Pump with 8 Channels for High-Throughput Slurry Feeding, EAHTSFPSP8C","description":"\u003cp\u003eFor high-precision slot-die coating, a high-pressure syringe pump is the standard delivery system. Unlike a doctor blade where thickness is controlled by a mechanical gap, slot-die coating is a pre-metered process—the wet film thickness is directly proportional to the pump's flow rate and inversely proportional to the coating speed.\u003c\/p\u003e\n\u003cp\u003eTo achieve a uniform, streak-free coating, the syringe pump should meet these technical criteria: (1) \u003cstrong\u003ePulse-Free Flow\u003c\/strong\u003e: The motor must have high micro-stepping resolution. Any \"pulsing\" in the flow will result in visible transverse \"ribbing\" or waves in your dried electrode. (2) \u003cstrong\u003eHigh Torque\/Linear Force\u003c\/strong\u003e: Battery and CDI slurries are often highly viscous (\"peanut butter\" consistency). Standard medical syringe pumps will often \"stall\" or \"slip.\" You need a laboratory-grade pump with at least 20–40 lbs (9–18 kg) of linear force. (3) \u003cstrong\u003eChemical Compatibility\u003c\/strong\u003e: The syringe itself should be stainless steel or glass with a PTFE-tipped plunger. Plastic syringes can swell or leach when used with solvents like NMP (N-Methyl-2-pyrrolidone).\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEAHTSFPSP8C (E-A-HSF-PSP8C)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan\u003eAC110-220V±10%, single phase, 50\/60Hz, ~10 W\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSyringe Sizes\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA 10mL syringe is included\u003c\/li\u003e\n\u003cli\u003eOther syringe sizes within 0.5-10 mL are available upon request\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePumping Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe infusion rates range from 0.568 uL\/hr (1mL syringe) to 380 mL\/hr (10mL syringe).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCEPSP8C_02_160x160.png?v=1775063606\" alt=\"\" style=\"float: none;\"\u003e            \u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12541-020-00425-6\"\u003eH. Lee, et al., Design and Assembly of a Thin-Film-Based Micro Pump for a Micro-slot Die, International Journal of Precision Engineering and Manufacturing, 2020, 21, 2335–2344\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/aiche.onlinelibrary.wiley.com\/doi\/full\/10.1002\/aic.15268\"\u003eX. Ding, et al., A review of the operating limits in slot die coating processes, AICHE J., 2016, 62, 2508-2524\u003c\/a\u003e. \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"Scientific Instruments","offers":[{"title":"Default Title","offer_id":47502300119270,"sku":"EAHTSFPSP8C","price":899.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASFEPSP8C_main.png?v=1775087645"},{"product_id":"eseltccbhvb","title":"ECS-SEL Tape Casting Coater with Bottom Heating (120℃) and Vacuum Bed (L1000*W500 mm), ESELTCCBHVB","description":"\u003cp\u003eFor lab-scale tape casting (also known as doctor blade coating), the most effective systems combine a high-precision vacuum chuck to hold the substrate flat and an integrated heating element to control the drying process. These features are critical for producing uniform, crack-free films for battery electrodes, fuel cell membranes, or ceramic tapes.\u003c\/p\u003e\n\u003cp\u003eThe key selection criteria of an appropriate tape casting coater: (1) \u003cstrong\u003eVacuum Bed\u003c\/strong\u003e: Essential for keeping thin foils (like Copper or Aluminum) or polymer films from wrinkling during the coating stroke. (2) \u003cstrong\u003eHeating Method\u003c\/strong\u003e: Top heating (infrared or convection) dries the slurry surface first, while bottom heating (heated bed) transfers heat through the substrate. (3) \u003cstrong\u003eCoating Speed\u003c\/strong\u003e: Look for variable speed control (typically 0–100 mm\/s) to match the rheology of your specific slurry. (4) \u003cstrong\u003eDoctor Blade Compatibility\u003c\/strong\u003e: Most of these units are compatible with adjustable micrometer doctor blades or fixed-gap film applicators.\u003c\/p\u003e\n\u003ctable style=\"height: 951.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESELTCCBHVB (ESEL-TCCBHVB)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 2000 W\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 86.8px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 86.8px;\"\u003e\u003cem\u003eCoating Area\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 86.8px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe aluminum alloy vacuum bed area is L1100*W550mm, which enable the effective coating area is L1000mm * W500 mm (depends on the film applicator is used).  \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003eCoating Speed\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e5-80 mm\/s\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 106.4px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 106.4px;\"\u003e\u003cem\u003eHeating Model \u0026amp; Temperature\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 106.4px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 120 ℃ (±1°C, single-point control)\u003c\/li\u003e\n\u003cli\u003eMax. heating rate: 5-8 °C\/min, bottom resistance heating\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan style=\"font-size: 0.875rem;\"\u003eTop-cover heating with resistance, IR, UV heating can be customized upon request. \u003c\/span\u003e\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 265.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 265.2px;\"\u003e\n\u003cp\u003eFilm Applicator (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional, not included\u003c\/span\u003e)\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 265.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 1\u003c\/strong\u003e: \u003cspan\u003eDoctor Blade (500 mm width, \u003ca href=\"https:\/\/echemsupplies.com\/products\/etccafa?variant=47520265273574\"\u003eETCCAFAW500\u003c\/a\u003e\u003ca href=\"https:\/\/echemsupplies.com\/products\/essafsfafg?variant=47491848863974\"\u003e\u003c\/a\u003e)\u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003e          \u003c\/span\u003e\u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETCCAFA_03_100x100.png?v=1775601057\"\u003e\u003cstrong\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\u003c\/ul\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOption 2\u003c\/strong\u003e: Hybrid film applicator (slot die + doctor blade) with 500 mm coating width \u003ca href=\"https:\/\/echemsupplies.com\/products\/essahfaw80?variant=47520286638310\"\u003eESSAHFASD500\u003c\/a\u003e\u003ca href=\"https:\/\/echemsupplies.com\/products\/essahfaw80?variant=47501068435686\"\u003e.\u003c\/a\u003e  For slot die coating, the large syringe pump \u003ca href=\"https:\/\/echemsupplies.com\/products\/easdcldcsp?variant=47520463782118\"\u003eEASDCLDCSP\u003c\/a\u003e can be considered.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMTCCIHCVB_07_100x100.png?v=1775601542\"\u003e       \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCLDCSP_main_100x100.png?v=1775609112\" alt=\"\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 187.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 187.6px;\"\u003e\u003cem\u003eVacuum Pump (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional, not included\u003c\/span\u003e)\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 187.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA vacuum pump (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esovp?variant=47512544542950\"\u003eESOVP\u003c\/a\u003e) is externally connected for vacuum chunk operation.\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESOVP_main_100x100.png?v=1775407970\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 67.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 67.2px;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 67.2px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL1280 * W620 * H430 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~90 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0272884217301475\"\u003eJ. Ko, et al., Thin cathode for thermal batteries using a tape-casting process, Ceramic International, 2017, 43, 5789-5793\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.4c18516\"\u003eH. Zhao, et al., Tape-Casting Fabrication Techniques for Garnet-Based Membranes in Solid-State Lithium-Metal Batteries: A Comprehensive Review, ACS Appl. Mater. Interfaces 2024, 16, 50, 68772–68793\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47520259309798,"sku":"ESELTCCBHVB","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESELTCCBHVB_main.png?v=1775602163"},{"product_id":"easdcldcsp","title":"Large Digital-Controlled Syringe Pump (500 mL \u0026 1000 mL) for Slot Die Coater, EASDCLDCSP","description":"\u003cp\u003eFor high-precision slot-die coating, a high-pressure syringe pump is the standard delivery system. Unlike a doctor blade where thickness is controlled by a mechanical gap, slot-die coating is a pre-metered process—the wet film thickness is directly proportional to the pump's flow rate and inversely proportional to the coating speed.\u003c\/p\u003e\n\u003cp\u003eTo achieve a uniform, streak-free coating, the syringe pump should meet these technical criteria: (1) \u003cstrong\u003ePulse-Free Flow\u003c\/strong\u003e: The motor must have high micro-stepping resolution. Any \"pulsing\" in the flow will result in visible transverse \"ribbing\" or waves in your dried electrode. (2) \u003cstrong\u003eHigh Torque\/Linear Force\u003c\/strong\u003e: Battery and CDI slurries are often highly viscous (\"peanut butter\" consistency). Standard medical syringe pumps will often \"stall\" or \"slip.\" You need a laboratory-grade pump with at least 20–40 lbs (9–18 kg) of linear force. (3) \u003cstrong\u003eChemical Compatibility\u003c\/strong\u003e: The syringe itself should be stainless steel or glass with a PTFE-tipped plunger. Plastic syringes can swell or leach when used with solvents like NMP (N-Methyl-2-pyrrolidone).\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEASDCLDCSP (E-A-SDC-LDCSP)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan\u003eAC110-220V±10%, single phase, 50\/60Hz, ~120 W\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eA DC24V adaptor is included. \u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSpeed Range\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e0.17-20 mL\/s (adjustable on touch-screen)\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSyringe Sizes\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e500 mL or 1000 mL \u003c\/li\u003e\n\u003cli\u003eI.D. 65 mm, O.D. 165 mm\u003c\/li\u003e\n\u003cli\u003eSS316\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eConnection Tubing\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eTeflon Tubing, O.D. 10mm, I.D. 8mm \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eApplication\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIt can be integrated with large tape casting coaters, such as \u003ca href=\"https:\/\/echemsupplies.com\/products\/eseltccbhvb?variant=47520259309798\"\u003eESELTCCBHVB\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eIt can be used for roll-to-roll slot die coaters, such as \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e500 mL version L560×W230×H270mm\u003c\/li\u003e\n\u003cli\u003e1000 mL version L680×W215×H286mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e18-22 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12541-020-00425-6\"\u003eH. Lee, et al., Design and Assembly of a Thin-Film-Based Micro Pump for a Micro-slot Die, International Journal of Precision Engineering and Manufacturing, 2020, 21, 2335–2344\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/aiche.onlinelibrary.wiley.com\/doi\/full\/10.1002\/aic.15268\"\u003eX. Ding, et al., A review of the operating limits in slot die coating processes, AICHE J., 2016, 62, 2508-2524\u003c\/a\u003e. \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"500 mL","offer_id":47520463782118,"sku":"EASDCLDCSP500","price":3199.0,"currency_code":"USD","in_stock":true},{"title":"1000 mL","offer_id":47520463814886,"sku":"EASDCLDCSP1000","price":3999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCLDCSP_main.png?v=1775609112"},{"product_id":"essmr2rc","title":"ECS-SS Multifunctional Roll-to-Roll Coater (Max. 160 mm, Doctor Balde, Reverse Comma, Slot Die, and Microgravure), ESSMR2RC","description":"\u003cp\u003eA high-end lab R2R coater normally offer interchangeable heads: (1) \u003cstrong\u003eSlot-Die Coating\u003c\/strong\u003e: The industry standard for high-precision battery electrodes. It uses a shim and a precision pump to \"meter\" the slurry. This is ideal for your NMP slurries as it minimizes solvent evaporation at the coating head. (2) \u003cstrong\u003eComma Doctor \/ Reverse Comma\u003c\/strong\u003e: Excellent for high-viscosity slurries. It uses a rotating \"comma\" roller to set the wet thickness. (3) \u003cstrong\u003eMicro-Gravure\u003c\/strong\u003e: Best for very thin coatings (like functional ceramic layers on separators or thin ion-exchange membranes). It uses a patterned roller to transfer a precise volume of liquid.\u003c\/p\u003e\n\u003cp\u003eGeneral Introduction of R2R coating methods:\u003c\/p\u003e\n\u003cp\u003e(1). \u003cstrong\u003eDoctor Blade Coating\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_02.png?v=1775622122\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003eIn a R2R setup, doctor blade coating is normally called Knife-over-Roll coating. It mainly consists of (1) \u003cstrong\u003eWeb\u003c\/strong\u003e: The aluminum or copper foil is pulled over a high-precision backup roller. (2) \u003cstrong\u003eReservoir\u003c\/strong\u003e: A \"dam\" of slurry is maintained just behind the blade. (3) \u003cstrong\u003eMetering\u003c\/strong\u003e: As the foil moves, the blade (the \"knife\") scrapes off excess slurry. The thickness of the wet coating is determined by the gap between the blade edge and the foil surface. The wet thickness T= Gap * K (where K is a factor, that is usually around 0.5 to 0.7, depending on the slurry's viscosity and the web speed.)\u003c\/p\u003e\n\u003cp\u003e(2). \u003cstrong\u003eReverse Comma Coating (also called Transfer Comma Coating)\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_03.png?v=1775622183\" alt=\"\" width=\"140\" height=\"102\"\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eUnlike a standard doctor blade where the foil moves under a stationary knife, a reverse comma system uses a three-roll or two-roll configuration to \"transfer\" a metered film of slurry onto the foil. The key components and features are: (1) \u003cstrong\u003eComma Roller\u003c\/strong\u003e: A high-precision steel cylinder with a \"comma-shaped\" cross-section. It doesn't move during the coating process; instead, it acts as a high-precision gate. (2) \u003cstrong\u003eApplicator (Back-up) Roller\u003c\/strong\u003e: This roller rotates in the opposite direction (reverse) to the web travel. It picks up the slurry from a reservoir and carries it toward the comma gap. (3) \u003cstrong\u003eTransfer\u003c\/strong\u003e: As the foil (web) passes between the rollers, the metered slurry is wiped onto the foil.\u003c\/p\u003e\n\u003cp\u003e(3). \u003cstrong\u003eSlot Die Coating\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\u003cimg height=\"105\" width=\"130\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_04.png?v=1775622901\"\u003e\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003eWhile doctor blade and comma coating are \"metering\" methods (where you scrape off excess), slot-die is a \"pre-metered\" method. This means the exact volume of slurry pumped into the head is the exact volume that ends up on the foil. Normally slot die coating system consists of three main components: A high-precision pump (usually a syringe or gear pump), a slot-die head, and a back-up roller. The slot die coating head is mainly composed of (1)\u003cstrong\u003e Reservoir (Manifold)\u003c\/strong\u003e: The slurry is pumped into an internal cavity inside the die head designed to distribute the fluid evenly across the entire width. (2) \u003cstrong\u003eShim\u003c\/strong\u003e: A thin, precision-cut metal plate determines the width of the coating and the internal gap of the die. The coating bead is critical for the coating film quality, where the slurry emerges from a narrow \"slot\" and forms a liquid bridge (the \"bead\") between the die lips and the moving foil.\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e(3). \u003cstrong\u003eMicrogravure Coating\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\u003cstrong\u003e\u003cimg height=\"96\" width=\"169\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_05.png?v=1775623284\"\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003eMicrogravure coating is a specialized roll-to-roll (R2R) technique used for extremely thin, high-precision coatings. Unlike standard gravure, which uses large rollers and a doctor blade on the foil, microgravure uses a very small diameter engraved roll that rotates in the opposite direction to the web. The R2R microgravure coating system has a small, engraved \"gravure\" roll (typically 20mm to 50mm in diameter) that is partially submerged in a slurry reservoir. There are multiple distinct features: (1) \u003cstrong\u003eEngraving Roll\u003c\/strong\u003e: The roll surface is covered in microscopic cells (patterns like honeycombs or pyramids). The \"cell volume\" determines exactly how much liquid is picked up. (2) \u003cstrong\u003eReverse Rotation\u003c\/strong\u003e: The roll rotates in the opposite direction of the foil (web). This \"kiss-coating\" action shears the liquid as it transfers, resulting in a much smoother surface than traditional gravure. (3) \u003cstrong\u003eDoctor Blade\u003c\/strong\u003e: A flexible blade scrapes the excess slurry off the roll before it touches the foil, ensuring only the liquid inside the engraved cells is transferred.\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\n\u003cstrong\u003e\u003c\/strong\u003e\u003cbr\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\" style=\"height: 3113.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 47.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSMR2RC (ESS-MR2RC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 47.6px;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 3550 W\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 145.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 145.6px;\"\u003e\u003cem\u003eGeneral Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 145.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eRoller width: 200 mm \u003c\/li\u003e\n\u003cli\u003eLoading substrate width: Max. 180 mm\u003c\/li\u003e\n\u003cli\u003eCoating width: Max. 160 mm\u003c\/li\u003e\n\u003cli\u003eMechanical coating speed: 0.01-1.0m\/min (the real coating speed depends on the slurry properties and dry oven length\/temperature)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 145.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 145.6px;\"\u003e\u003cem\u003eUnwinding\/Winding Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 145.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eRoller diameter: 3\", mechanical expansion for tightening the loading roll substrate and collection cardboard. \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eMax. winding\/unwinding roll diameter: 250 mm \u003c\/li\u003e\n\u003cli\u003eAlignment Sensors were installed and aligning position resolution could be 0.3 mm. \u003c\/li\u003e\n\u003cli\u003eCoating Roller: Stainless Steel with surface Cr coating, Ф80mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 1917.4px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 1917.4px;\"\u003e\u003cem\u003eCoating Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 1917.4px;\"\u003e\n\u003cp\u003e   (1) \u003cstrong\u003eDoctor Blade\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e            \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_06_100x100.png?v=1775625753\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe doctor blade is made of SS with surface Cr coating and its diameter is Ф50mm. \u003c\/li\u003e\n\u003cli\u003eThe coating width is 0-160 mm, which can be adjusted by the blocking foam. \u003c\/li\u003e\n\u003cli\u003eSlurry Viscosity: 2000-6000 cP (recommended, higher viscosity up to 10000-15000 cP may also work for thicker electrode).\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003eEABSFPP2L\u003c\/a\u003e can be considered. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EABSFPP2L_main_100x100.png?v=1775628781\"\u003e\u003c\/p\u003e\n\u003cp\u003e    (2) \u003cstrong\u003eReverse Comma\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e         \u003c\/strong\u003e\u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_07_100x100.png?v=1775627010\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe coating roller is made of SS with surface Cr coating and its diameter is Ф80mm. \u003c\/li\u003e\n\u003cli\u003eThe backing roller is made of rubber (Ф80mm, pneumatic)\u003c\/li\u003e\n\u003cli\u003eThe comma bar is made of SS with surface Cr coating and its diameter is Ф50mm.\u003c\/li\u003e\n\u003cli\u003eThe coating width is 0-160 mm, which can be adjusted by the blocking foam. \u003c\/li\u003e\n\u003cli\u003eSlurry Viscosity: 2000-12000 cP (recommended)\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003eEABSFPP2L\u003c\/a\u003e can be considered. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e    (3) \u003cstrong\u003eSlot Die \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e        \u003c\/strong\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_08_100x100.png?v=1775629992\" alt=\"\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe coating roller is made of SS with surface Cr coating and its diameter is Ф80mm. \u003c\/li\u003e\n\u003cli\u003eThe coating width is 0-160 mm, which can be adjusted by the opening mouth of shims. The standard shim thickness is 0.2, 0.3, 0.4, 0.5mm. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_09_100x100.png?v=1775630854\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry Viscosity: 50-12000 cP. For battery application, slurry viscosity is recommended in 2000-8000 cP. \u003c\/li\u003e\n\u003cli\u003eThe precise screw pump \u003ca href=\"https:\/\/echemsupplies.com\/products\/easdcpsp?variant=47522239578342\"\u003eEASDCPSP\u003c\/a\u003e is the best option for stable slot die coating.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003ca href=\"https:\/\/echemsupplies.com\/products\/easdcpsp?variant=47522239578342\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCPSP_main_100x100.png?v=1775632530\" alt=\"\" style=\"float: none;\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFor intermittent coating (or pattern coating) for cylindrical electrode application, the intermittent valve system is highly recommended. For simultaneous dual-layer coating, a customized dual-channel slot die head (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esar2rcsdh?variant=47523176710374\"\u003eESAR2RCSDH\u003c\/a\u003e) can be supplied. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_10_100x100.png?v=1775633700\" alt=\"\" style=\"float: none;\"\u003e     \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_15_100x100.png?v=1775662134\"\u003e    \u003cimg height=\"82\" width=\"128\" style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_16_100x100.png?v=1775662200\"\u003e\u003c\/p\u003e\n\u003cp\u003e   (4) \u003cstrong\u003eMicrogravure\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e    \u003c\/strong\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_11_100x100.png?v=1775633910\" alt=\"\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eA standard microgravure rod with Ф30mm is included. The parameters, such as coating width, engraved pattern, mesh number and depth can be customized. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_12_100x100.png?v=1775634349\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry Viscosity: 20-2000 cP.\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003eEABSFPP2L\u003c\/a\u003e can be considered. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 331.8px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 331.8px;\"\u003e\u003cem\u003eHeating Oven Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 331.8px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eHeating mode: Convection heating (hot air flow). Other heating methods of IR and UV can be customized upon request. Various heating modules are switchable. \u003c\/li\u003e\n\u003cli\u003eHeating temperature: Max.130℃\u003c\/li\u003e\n\u003cli\u003eHeating oven length: 0.5 m (standard version). If customer want to increase the heating oven length to increase the coating speed, the dual-heating-oven design can be supplied. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_13_160x160.png?v=1775634733\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eVentilation: air flow: 570m³\/h, 5\" aluminum pipe\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 145.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 145.6px;\"\u003e\n\u003cp\u003eTension Control System\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 145.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eTension range: 10-40 N (resolution is ±3 N), which is controlled by swing roller system.\u003c\/li\u003e\n\u003cli\u003eFor low-tension substrate coating (eg: separator and membrane), the specially designed low tension version is highly recommended since its lowest tension can be down to 5 N.  \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 187.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 187.6px;\"\u003e\u003ci\u003eGas Compressor\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 187.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA gas compressor (\u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e) is needed to provide 60-80 psi for pneumatic operation.\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EUQOFGC_main_100x100.png?v=1775414665\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 86.8px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 86.8px;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 86.8px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 10px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 10px;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 10px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL1100 * W780 * H960 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 47.6px;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~560 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0255270112001997\"\u003eM. Schmitt, et al., Slot-die processing of lithium-ion battery electrodes—Coating window characterization, Chemical Engineering and Processing: Process Intensification, 2013, 68, 32-37\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1088\/1361-6463\/aafbf3\/meta\"\u003eH. Li, et al., High-performance supercapacitor carbon electrode fabricated by large-scale roll-to-roll micro-gravure printing,  J. Phys. D: Appl. Phys., 2019, 52, 115501\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s40095-022-00481-w\"\u003eL. A. Román-Ramírez, et al., Effect of coating operating parameters on electrode physical characteristics and final electrochemical performance of lithium-ion batteries, International Journal of Energy and Environmental Engineering, 2022, 13, 943-953\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Doctor Blade","offer_id":47522438381798,"sku":"ESSMR2RCDB","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Reverse Comma","offer_id":47522438414566,"sku":"ESSMR2RCRC","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Slot Die","offer_id":47522438447334,"sku":"ESSMR2RCSD","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Microgravure","offer_id":47522438480102,"sku":"ESSMR2RCMG","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Blade + Slot Die","offer_id":47522438512870,"sku":"ESSMR2RCBSD","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Reverse Comma + Slot Die","offer_id":47522438545638,"sku":"ESSMR2RCRCSD","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_main.png?v=1775621348"},{"product_id":"eabsfpp2l","title":"Peristaltic Pump (2 L) for Battery Slurry Feeding, EABSFPP2L","description":"\u003cp\u003eIn battery slurry preparation and coating, the peristaltic pump is one of the popular choice for transferring slurry from the mixing tank to the coating area, such as doctor blade, reverse comma bar, and microgravure.\u003c\/p\u003e\n\u003cp\u003ePeristaltic pumps offer specific advantages: (1) \u003cstrong\u003eZero Contamination\u003c\/strong\u003e: The slurry remains entirely contained within the tubing. This prevents metallic particles from pump gears from leaching into the slurry, which would otherwise cause micro-shorts in your pouch cells. (2) \u003cstrong\u003eShear-Thinning Friendly\u003c\/strong\u003e: Many battery slurries are non-Newtonian. The gentle \"squeezing\" action of the rollers minimizes mechanical shear, preventing the breakdown of long-chain PVDF binders or the \"clumping\" of conductive carbon. (3) \u003cstrong\u003eHandling High Solids\u003c\/strong\u003e: Peristaltic pumps can easily move high-viscosity slurries with high solids content (up to 70%+) that would clog or seize a standard mechanical pump. (4) \u003cstrong\u003eEasy Cleanup\u003c\/strong\u003e: You only need to clean or replace the tubing. This is a massive time-saver when switching between different cathode recipes (e.g., NMC 811 to LFP).\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEABSFPP2L (E-A-BSF-PP2L)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan\u003eAC110-220V±10%, single phase, 50\/60Hz, ~100 W\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eA DC24V adaptor is included. \u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eFeeding Speed Range\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003eMax. ~33 mL\/s (adjustable by rotating the speed knob)\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSlurry Tank\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e2 L in total, SS304\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eFeeding Channels\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eTwo separate slurry feeding channels are designed for anode and cathode. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eHeating Jacket (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional\u003c\/span\u003e)\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe heating function (\u0026lt;150 degree) is available to maintain the temperature upon request. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eApplication\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIt can be integrated with large tape casting coaters, such as \u003ca href=\"https:\/\/echemsupplies.com\/products\/eseltccbhvb?variant=47520259309798\"\u003eESELTCCBHVB\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eIt can be used for roll-to-roll slot die coaters, such as \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL320×W180×H210mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~ 3 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12541-020-00425-6\"\u003eH. Lee, et al., Design and Assembly of a Thin-Film-Based Micro Pump for a Micro-slot Die, International Journal of Precision Engineering and Manufacturing, 2020, 21, 2335–2344\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/aiche.onlinelibrary.wiley.com\/doi\/full\/10.1002\/aic.15268\"\u003eX. Ding, et al., A review of the operating limits in slot die coating processes, AICHE J., 2016, 62, 2508-2524\u003c\/a\u003e. \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47522046673126,"sku":"EABSFPP2L","price":999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EABSFPP2L_main.png?v=1775628781"},{"product_id":"easdcpsp","title":"Precise Screw Pump (5 L) for Slot Die Coater, EASDCPSP","description":"\u003cp\u003eFor high-precision slot-die coating of NMP-based cathode slurries, a precise screw pump (specifically a Progressive Cavity Pump) is often considered superior to a peristaltic pump for industrial or high-end R\u0026amp;D. While peristaltic pumps are easier to clean, screw pumps provide a pulseless, continuous flow that is critical for eliminating \"chatter marks\" (thickness ripples) on your electrodes at higher coating speeds.\u003c\/p\u003e\n\u003cp\u003eA screw pump consists of a single-helix metallic rotor and a double-helix elastic stator. As the rotor turns inside the stator, it creates a series of sealed \"cavities\" that move from the suction side to the discharge side. (1) \u003cstrong\u003eVolumetric Precision\u003c\/strong\u003e: The amount of slurry delivered is directly proportional to the rotation speed. (2) \u003cstrong\u003ePulseless Delivery\u003c\/strong\u003e: Unlike peristaltic or piston pumps, the geometry of the cavities ensures that the displaced volume is constant. This results in an incredibly smooth \"coating bead\" at the slot-die lip.\u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEASDCPSP (E-A-SDC-PSP)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan\u003eAC220V±10%, single phase, 50\/60Hz, ~500 W\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eFeeding Speed Range\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e5.2 to 186 mL\/min, adjustable\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003eStirring speed: ~30 rpm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSlurry Tank\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e5 L in total, SS304 (2L and 10 L are also available upon request)\u003c\/li\u003e\n\u003cli\u003eThe stator is made of EPDM.\u003c\/li\u003e\n\u003cli\u003eThe rotor is made of SUS316\u003c\/li\u003e\n\u003cli\u003eIt is compatible with NMP solvent\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eAir Compressor\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIf the screw pump is connected with the R2R coater, the gas pressure is coming from the coater by a connected gas pressure tubing.\u003c\/li\u003e\n\u003cli\u003eIf the screw pump is individually purchased or used, then an individual air compressor (\u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e) is needed. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EUQOFGC_main_100x100.png?v=1775414665\" alt=\"\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eApplication\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIt is a good option for roll-to-roll slot die coaters, such as \u003ca href=\"ESSMR2RC\"\u003eESSMR2RC\u003c\/a\u003e, \u003ca href=\"https:\/\/echemsupplies.com\/products\/esmmr2rc?variant=47523596108006\"\u003eESMMR2RC\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL920×W230×H830mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~ 35 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12541-020-00425-6\"\u003eH. Lee, et al., Design and Assembly of a Thin-Film-Based Micro Pump for a Micro-slot Die, International Journal of Precision Engineering and Manufacturing, 2020, 21, 2335–2344\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/aiche.onlinelibrary.wiley.com\/doi\/full\/10.1002\/aic.15268\"\u003eX. Ding, et al., A review of the operating limits in slot die coating processes, AICHE J., 2016, 62, 2508-2524\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47522239578342,"sku":"EASDCPSP","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCPSP_main.png?v=1775632530"},{"product_id":"esar2rcsdh","title":"Slot Die Head for Roll-to-Roll Coater, ESAR2RCSDH","description":"\u003cp\u003eSlot die head is the most critical part for roll-to-roll slot die coater. The performance of the slot die head depends on how it distributes the slurry from a single point (the inlet) to a wide, uniform line (the exit). (1) \u003cstrong\u003eManifold\u003c\/strong\u003e: It is the internal cavity (usually coat-hanger or T-shaped) designed to ensure that the fluid pressure is identical across the entire width of the die. For battery slurries, a coat-hanger manifold is preferred because it prevents \"dead zones\" where NMP-based slurry could stagnate and dry out. (2) \u003cstrong\u003eDie Lips\u003c\/strong\u003e: The \"lips\" are the final exit point. They must be polished to a mirror finish (typically Ra \u0026lt; 0.0 um) and have a \"sharpness\" radius of less than 10 um. This sharpness is what allows the liquid \"bead\" to break cleanly when doing intermittent (patch) coating.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 464.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESAR2RCSDH (ESA-R2RC-SDH)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDie Material\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eSlot die head: SUS630\u003c\/li\u003e\n\u003cli\u003eOther parts contacted with slurry: SUS304\u003c\/li\u003e\n\u003cli\u003eSealing parts: silicone, EPDM, PTFE\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 316px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 316px;\"\u003e\u003cem\u003eCoating Head Types\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 316px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eRegular Single Layer Coating (Manifold: semi-sphere, single channel)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e         \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESAR2RCSDH_02_100x100.png?v=1775664057\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e Special Dual-Layer Coating (Manifold: semi-sphere, dual- channel)\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_15_100x100.png?v=1775662134\"\u003e    \u003cimg height=\"84\" width=\"131\" style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_16_100x100.png?v=1775662200\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eInlet\/Outlet Connection\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eInlet: φ34mm, quick connection\u003c\/li\u003e\n\u003cli\u003eVentilation: G3⁄8\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003eCoating Width\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 160 mm, 260 mm, and 360 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 53px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 53px;\"\u003e\u003cem\u003eApplication\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 53px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThese slot die coating heads are compatible with ESSMR2RC, ESMMR2RC, and ESLMR2RC. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDimension\/Weight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESAR2RCSDH160: L220*W135*H120mm (25 kg)\u003c\/li\u003e\n\u003cli\u003eESAR2RCSDH260: L320*W135*H120mm (38 kg)\u003c\/li\u003e\n\u003cli\u003eESAR2RCSDH360: L420*W135*H120mm (50 kg)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1088\/1757-899X\/1237\/1\/012014\/meta\"\u003eF. Sarka, et al., Design Issues for Slot-Die Coating Heads - Case Study, IOP Conf. Ser.: Mater. Sci. Eng. 2022, 1237, 012014\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/aiche.onlinelibrary.wiley.com\/doi\/full\/10.1002\/aic.15268\"\u003eX. Ding, et al., A review of the operating limits in slot die coating processes, AICHE J, 2016, 62, 2508-2524\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1140\/epjs\/s11734-024-01398-7\"\u003eA. Hoffmann, et al., Optimized battery electrodes with primer layers by simultaneous two-layer slot-die coating, The European Physical Journal Special Topics, 2025, 234, 3065–3076\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Single-Channel (160 mm)","offer_id":47523176710374,"sku":"ESAR2RCSDHSC160","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Singe-Channel (260 mm)","offer_id":47523176743142,"sku":"ESAR2RCSDHSC260","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Single-Channel (360 mm)","offer_id":47523176775910,"sku":"ESAR2RCSDHSC360","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Dual-Channel (160 mm)","offer_id":47523176808678,"sku":"ESAR2RCSDHDC160","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Dual-Channel (260 mm)","offer_id":47523176841446,"sku":"ESAR2RCSDHDC260","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Dual-Channel (360 mm)","offer_id":47523176874214,"sku":"ESAR2RCSDHDC360","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESAR2RCSDH_main.png?v=1775663653"},{"product_id":"esmmr2rc","title":"ECS-SM Multifunctional Roll-to-Roll Coater (Max. 260 mm, Doctor Balde, Reverse Comma, Slot Die, and Microgravure), ESMMR2RC","description":"\u003cp\u003eA high-end lab R2R coater normally offer interchangeable heads: (1) \u003cstrong\u003eSlot-Die Coating\u003c\/strong\u003e: The industry standard for high-precision battery electrodes. It uses a shim and a precision pump to \"meter\" the slurry. This is ideal for your NMP slurries as it minimizes solvent evaporation at the coating head. (2) \u003cstrong\u003eComma Doctor \/ Reverse Comma\u003c\/strong\u003e: Excellent for high-viscosity slurries. It uses a rotating \"comma\" roller to set the wet thickness. (3) \u003cstrong\u003eMicro-Gravure\u003c\/strong\u003e: Best for very thin coatings (like functional ceramic layers on separators or thin ion-exchange membranes). It uses a patterned roller to transfer a precise volume of liquid.\u003c\/p\u003e\n\u003cp\u003eGeneral Introduction of R2R coating methods:\u003c\/p\u003e\n\u003cp\u003eA high-end lab R2R coater normally offer interchangeable heads: (1) \u003cstrong\u003eSlot-Die Coating\u003c\/strong\u003e: The industry standard for high-precision battery electrodes. It uses a shim and a precision pump to \"meter\" the slurry. This is ideal for your NMP slurries as it minimizes solvent evaporation at the coating head. (2) \u003cstrong\u003eComma Doctor \/ Reverse Comma\u003c\/strong\u003e: Excellent for high-viscosity slurries. It uses a rotating \"comma\" roller to set the wet thickness. (3) \u003cstrong\u003eMicro-Gravure\u003c\/strong\u003e: Best for very thin coatings (like functional ceramic layers on separators or thin ion-exchange membranes). It uses a patterned roller to transfer a precise volume of liquid.\u003c\/p\u003e\n\u003cp\u003eGeneral Introduction of R2R coating methods:\u003c\/p\u003e\n\u003cp\u003e(1). \u003cstrong\u003eDoctor Blade Coating\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_02.png?v=1775622122\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003eIn a R2R setup, doctor blade coating is normally called Knife-over-Roll coating. It mainly consists of (1) \u003cstrong\u003eWeb\u003c\/strong\u003e: The aluminum or copper foil is pulled over a high-precision backup roller. (2) \u003cstrong\u003eReservoir\u003c\/strong\u003e: A \"dam\" of slurry is maintained just behind the blade. (3) \u003cstrong\u003eMetering\u003c\/strong\u003e: As the foil moves, the blade (the \"knife\") scrapes off excess slurry. The thickness of the wet coating is determined by the gap between the blade edge and the foil surface. The wet thickness T= Gap * K (where K is a factor, that is usually around 0.5 to 0.7, depending on the slurry's viscosity and the web speed.)\u003c\/p\u003e\n\u003cp\u003e(2). \u003cstrong\u003eReverse Comma Coating (also called Transfer Comma Coating)\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_03.png?v=1775622183\" alt=\"\" width=\"140\" height=\"102\"\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eUnlike a standard doctor blade where the foil moves under a stationary knife, a reverse comma system uses a three-roll or two-roll configuration to \"transfer\" a metered film of slurry onto the foil. The key components and features are: (1) \u003cstrong\u003eComma Roller\u003c\/strong\u003e: A high-precision steel cylinder with a \"comma-shaped\" cross-section. It doesn't move during the coating process; instead, it acts as a high-precision gate. (2) \u003cstrong\u003eApplicator (Back-up) Roller\u003c\/strong\u003e: This roller rotates in the opposite direction (reverse) to the web travel. It picks up the slurry from a reservoir and carries it toward the comma gap. (3) \u003cstrong\u003eTransfer\u003c\/strong\u003e: As the foil (web) passes between the rollers, the metered slurry is wiped onto the foil.\u003c\/p\u003e\n\u003cp\u003e(3). \u003cstrong\u003eSlot Die Coating\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_04.png?v=1775622901\" alt=\"\" width=\"130\" height=\"105\"\u003e\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003eWhile doctor blade and comma coating are \"metering\" methods (where you scrape off excess), slot-die is a \"pre-metered\" method. This means the exact volume of slurry pumped into the head is the exact volume that ends up on the foil. Normally slot die coating system consists of three main components: A high-precision pump (usually a syringe or gear pump), a slot-die head, and a back-up roller. The slot die coating head is mainly composed of (1)\u003cstrong\u003e Reservoir (Manifold)\u003c\/strong\u003e: The slurry is pumped into an internal cavity inside the die head designed to distribute the fluid evenly across the entire width. (2) \u003cstrong\u003eShim\u003c\/strong\u003e: A thin, precision-cut metal plate determines the width of the coating and the internal gap of the die. The coating bead is critical for the coating film quality, where the slurry emerges from a narrow \"slot\" and forms a liquid bridge (the \"bead\") between the die lips and the moving foil.\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e(3). \u003cstrong\u003eMicrogravure Coating\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\u003cstrong\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_05.png?v=1775623284\" alt=\"\" width=\"169\" height=\"96\"\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003eMicrogravure coating is a specialized roll-to-roll (R2R) technique used for extremely thin, high-precision coatings. Unlike standard gravure, which uses large rollers and a doctor blade on the foil, microgravure uses a very small diameter engraved roll that rotates in the opposite direction to the web. The R2R microgravure coating system has a small, engraved \"gravure\" roll (typically 20mm to 50mm in diameter) that is partially submerged in a slurry reservoir. There are multiple distinct features: (1) \u003cstrong\u003eEngraving Roll\u003c\/strong\u003e: The roll surface is covered in microscopic cells (patterns like honeycombs or pyramids). The \"cell volume\" determines exactly how much liquid is picked up. (2) \u003cstrong\u003eReverse Rotation\u003c\/strong\u003e: The roll rotates in the opposite direction of the foil (web). This \"kiss-coating\" action shears the liquid as it transfers, resulting in a much smoother surface than traditional gravure. (3) \u003cstrong\u003eDoctor Blade\u003c\/strong\u003e: A flexible blade scrapes the excess slurry off the roll before it touches the foil, ensuring only the liquid inside the engraved cells is transferred.\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESMMR2RC (ESM-MR2RC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 7500 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eGeneral Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eRoller width: 300 mm \u003c\/li\u003e\n\u003cli\u003eLoading substrate width: Max. 280 mm\u003c\/li\u003e\n\u003cli\u003eCoating width: Max. 260 mm\u003c\/li\u003e\n\u003cli\u003eMechanical coating speed: 0.01-2.0m\/min (the real coating speed depends on the slurry properties and dry oven length\/temperature)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eUnwinding\/Winding Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eRoller diameter: 3\", mechanical expansion for tightening the loading roll substrate and collection cardboard. \u003c\/li\u003e\n\u003cli\u003eMax. winding\/unwinding roll diameter: 250 mm \u003c\/li\u003e\n\u003cli\u003eAlignment Sensors were installed and aligning position resolution could be 0.5 mm. \u003c\/li\u003e\n\u003cli\u003eCoating Roller: Stainless Steel with surface Cr coating, Ф100mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCoating Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cp\u003e        (1) \u003cstrong\u003eDoctor Blade\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_06_100x100.png?v=1775625753\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe doctor blade is made of SS with surface Cr coating and its diameter is Ф100mm. \u003c\/li\u003e\n\u003cli\u003eThe coating width is 0-260 mm, which can be adjusted by the blocking foam. \u003c\/li\u003e\n\u003cli\u003eSlurry Viscosity: 2000-6000 cP (recommended, higher viscosity up to 10000-15000 cP may also work for thicker electrode).\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003eEABSFPP2L\u003c\/a\u003e or \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsflpp5l?variant=47523679863014\"\u003eEABSFLPP5L\u003c\/a\u003e can be considered. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e        \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EABSFPP2L_main_100x100.png?v=1775628781\" alt=\"\"\u003e \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsflpp5l?variant=47523679863014\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EABSFLPP5L_main_100x100.png?v=1775689239\" alt=\"\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e        (2) \u003cstrong\u003eReverse Comma (Transfer Coating)\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_07_100x100.png?v=1775627010\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe coating roller is made of SS with surface Cr coating and its diameter is Ф100mm. \u003c\/li\u003e\n\u003cli\u003eThe backing roller is made of rubber (Ф100mm, pneumatic)\u003c\/li\u003e\n\u003cli\u003eThe comma bar is made of SS with surface Cr coating and its diameter is Ф100mm.\u003c\/li\u003e\n\u003cli\u003eThe coating width is 0-260 mm, which can be adjusted by the blocking foam. \u003c\/li\u003e\n\u003cli\u003eSlurry Viscosity: 2000-12000 cP (recommended)\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003eEABSFPP2L\u003c\/a\u003e can be considered. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e        (3) \u003cstrong\u003eSlot Die \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMMR2RC_05_100x100.png?v=1775688285\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe coating roller is made of SS with surface Cr coating and its diameter is Ф100mm. \u003c\/li\u003e\n\u003cli\u003eThe coating width is 0-260 mm, which can be adjusted by the opening mouth of shims. The standard shim thickness is 0.2, 0.3, 0.4, 0.5mm. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_09_100x100.png?v=1775630854\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry Viscosity: 50-12000 cP. For battery application, slurry viscosity is recommended in 2000-8000 cP. \u003c\/li\u003e\n\u003cli\u003eThe precise screw pump \u003ca href=\"https:\/\/echemsupplies.com\/products\/easdcpsp?variant=47522239578342\"\u003eEASDCPSP\u003c\/a\u003e is the best option for stable slot die coating.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e         \u003ca href=\"https:\/\/echemsupplies.com\/products\/easdcpsp?variant=47522239578342\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCPSP_main_100x100.png?v=1775632530\" alt=\"\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFor intermittent coating (or pattern coating) for cylindrical electrode application, the intermittent valve system is highly recommended. For simultaneous dual-layer coating, a customized dual-channel slot die head (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esar2rcsdh?variant=47523176710374\"\u003eESAR2RCSDH\u003c\/a\u003e) can be supplied. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_10_100x100.png?v=1775633700\" alt=\"\"\u003e \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_15_100x100.png?v=1775662134\" alt=\"\"\u003e \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_16_100x100.png?v=1775662200\" alt=\"\" width=\"128\" height=\"82\"\u003e\u003c\/p\u003e\n\u003cp\u003e        (4) \u003cstrong\u003eMicrogravure\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMMR2RC_06_100x100.png?v=1775688286\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eA standard microgravure rod with Ф30mm is included. The parameters, such as coating width, engraved pattern, mesh number and depth can be customized. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_12_100x100.png?v=1775634349\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry Viscosity: 20-2000 cP.\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003eEABSFPP2L\u003c\/a\u003e can be considered. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eHeating Oven Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eHeating mode: Convection heating (hot air flow). Other heating methods of IR and UV can be customized upon request. Various heating modules are switchable.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMMR2RC_02_100x100.png?v=1775686106\" alt=\"\"\u003e \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMMR2RC_03_100x100.png?v=1775686032\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eHeating temperature: Max.130℃\u003c\/li\u003e\n\u003cli\u003eHeating oven length: 0.8 m (standard version). If customer want to increase the heating oven length to increase the coating speed, the dual-heating-oven design can be supplied. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_13_160x160.png?v=1775634733\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eVentilation: air flow: 570m³\/h, 5\" aluminum pipe\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003eTension Control System\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eTension range: 10-60 N (resolution is ±3 N), which is controlled by swing roller system.\u003c\/li\u003e\n\u003cli\u003eFor low-tension substrate coating (eg: separator and membrane), the specially designed low tension version is highly recommended since its lowest tension can be down to 5 N.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eGas Compressor\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eA gas compressor (\u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e) is needed to provide 60-80 psi for pneumatic operation.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e       \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EUQOFGC_main_100x100.png?v=1775414665\" alt=\"\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL2000 * W950 * H1300 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~1100 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0255270112001997\"\u003eM. Schmitt, et al., Slot-die processing of lithium-ion battery electrodes—Coating window characterization, Chemical Engineering and Processing: Process Intensification, 2013, 68, 32-37\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1088\/1361-6463\/aafbf3\/meta\"\u003eH. Li, et al., High-performance supercapacitor carbon electrode fabricated by large-scale roll-to-roll micro-gravure printing, J. Phys. D: Appl. Phys., 2019, 52, 115501\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s40095-022-00481-w\"\u003eL. A. Román-Ramírez, et al., Effect of coating operating parameters on electrode physical characteristics and final electrochemical performance of lithium-ion batteries, International Journal of Energy and Environmental Engineering, 2022, 13, 943-953\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Doctor Blade","offer_id":47523596108006,"sku":"ESMMR2RCDB","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Reverse Comma","offer_id":47523596140774,"sku":"ESMMR2RCRC","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Slot Die","offer_id":47523596173542,"sku":"ESMMR2RCSD","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Microgravure","offer_id":47523596206310,"sku":"ESMMR2RCMG","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Blade + Slot Die","offer_id":47523596239078,"sku":"ESMMR2RCBSD","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Reverse Comma + Slot Die","offer_id":47523596271846,"sku":"ESMMR2RCRCSD","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Blade + Reverse Comma + Slot Die","offer_id":47523649552614,"sku":"ESMMR2RCBRCSD","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMMR2RC_main.png?v=1775667380"},{"product_id":"eabsflpp5l","title":"Large Peristaltic Pump (5 L) for Battery Slurry Feeding, EABSFLPP5L","description":"\u003cp\u003eIn battery slurry preparation and coating, the peristaltic pump is one of the popular choice for transferring slurry from the mixing tank to the coating area, such as doctor blade, reverse comma bar, and microgravure.\u003c\/p\u003e\n\u003cp\u003ePeristaltic pumps offer specific advantages: (1) \u003cstrong\u003eZero Contamination\u003c\/strong\u003e: The slurry remains entirely contained within the tubing. This prevents metallic particles from pump gears from leaching into the slurry, which would otherwise cause micro-shorts in your pouch cells. (2) \u003cstrong\u003eShear-Thinning Friendly\u003c\/strong\u003e: Many battery slurries are non-Newtonian. The gentle \"squeezing\" action of the rollers minimizes mechanical shear, preventing the breakdown of long-chain PVDF binders or the \"clumping\" of conductive carbon. (3) \u003cstrong\u003eHandling High Solids\u003c\/strong\u003e: Peristaltic pumps can easily move high-viscosity slurries with high solids content (up to 70%+) that would clog or seize a standard mechanical pump. (4) \u003cstrong\u003eEasy Cleanup\u003c\/strong\u003e: You only need to clean or replace the tubing. This is a massive time-saver when switching between different cathode recipes (e.g., NMC 811 to LFP).\u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEABSFLPP5L (E-A-BSF-LPP5L)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan\u003eAC220V±10%, single phase, 50\/60Hz, ~500 W\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eFeeding Speed Range\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e0.001-720 mL\/min (adjustable by rotating the speed knob)\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSlurry Tank\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e5 L in total, SS304\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eFeeding Channels\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eTwo separate slurry feeding channels are designed for anode and cathode. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eGas Compressor\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA gas compressor (\u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e) is required to provide 60-80 psi gas pressure for pneumatic operation.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EUQOFGC_main_100x100.png?v=1775414665\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eApplication\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIt can be used for doctor blade reverse comma, and microgravure on a roll-to-roll coater, such as \u003ca href=\"https:\/\/echemsupplies.com\/products\/essmr2rc?variant=47522438381798\"\u003eESSMR2RC\u003c\/a\u003e, \u003ca href=\"https:\/\/echemsupplies.com\/products\/esmmr2rc?variant=47523596108006\"\u003eESMMR2RC\u003c\/a\u003e, and ESLMR2RC \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL600×W230×H750mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~ 58 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12541-020-00425-6\"\u003eH. Lee, et al., Design and Assembly of a Thin-Film-Based Micro Pump for a Micro-slot Die, International Journal of Precision Engineering and Manufacturing, 2020, 21, 2335–2344\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/aiche.onlinelibrary.wiley.com\/doi\/full\/10.1002\/aic.15268\"\u003eX. Ding, et al., A review of the operating limits in slot die coating processes, AICHE J., 2016, 62, 2508-2524\u003c\/a\u003e. \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47523679863014,"sku":"EABSFLPP5L","price":999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EABSFLPP5L_main.png?v=1775689239"},{"product_id":"easdclpsp","title":"Large Precise Screw Pump (10-40 L) for Slot Die Coater, EASDCLPSP","description":"\u003cp\u003eFor high-precision slot-die coating of NMP-based cathode slurries, a precise screw pump (specifically a Progressive Cavity Pump) is often considered superior to a peristaltic pump for industrial or high-end R\u0026amp;D. While peristaltic pumps are easier to clean, screw pumps provide a pulseless, continuous flow that is critical for eliminating \"chatter marks\" (thickness ripples) on your electrodes at higher coating speeds.\u003c\/p\u003e\n\u003cp\u003eA screw pump consists of a single-helix metallic rotor and a double-helix elastic stator. As the rotor turns inside the stator, it creates a series of sealed \"cavities\" that move from the suction side to the discharge side. (1) \u003cstrong\u003eVolumetric Precision\u003c\/strong\u003e: The amount of slurry delivered is directly proportional to the rotation speed. (2) \u003cstrong\u003ePulseless Delivery\u003c\/strong\u003e: Unlike peristaltic or piston pumps, the geometry of the cavities ensures that the displaced volume is constant. This results in an incredibly smooth \"coating bead\" at the slot-die lip.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEASDCLPSP (E-A-SDC-LPSP)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan\u003eAC220V±10%, single phase, 50\/60Hz, ~500 W\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eFeeding Speed Range\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e0.006 to 420 mL\/min, adjustable\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003eStirring speed: Max. ~50 rpm\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eSlurry Tank\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e10, 20, 40 L in total, SS304\u003c\/li\u003e\n\u003cli\u003eThe stator is made of EPDM.\u003c\/li\u003e\n\u003cli\u003eThe rotor is made of SUS316\u003c\/li\u003e\n\u003cli\u003eIt is compatible with NMP solvent\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eAir Compressor\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIf the screw pump is individually purchased or used, then an individual air compressor (\u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e) is needed. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003e\u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EUQOFGC_main_100x100.png?v=1775414665\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eApplication\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIt is a good option for roll-to-roll slot die coaters, such as ESLMR2RC, \u003ca href=\"https:\/\/echemsupplies.com\/products\/esmmr2rc?variant=47523596108006\"\u003eESMMR2RC\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL400×W400×H1100mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~ 45 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12541-020-00425-6\"\u003eH. Lee, et al., Design and Assembly of a Thin-Film-Based Micro Pump for a Micro-slot Die, International Journal of Precision Engineering and Manufacturing, 2020, 21, 2335–2344\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/aiche.onlinelibrary.wiley.com\/doi\/full\/10.1002\/aic.15268\"\u003eX. Ding, et al., A review of the operating limits in slot die coating processes, AICHE J., 2016, 62, 2508-2524\u003c\/a\u003e. \u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"10 L","offer_id":47523778822374,"sku":"EASDCLPSP10L","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"20 L","offer_id":47523778855142,"sku":"EASDCLPSP20L","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"40 L","offer_id":47523778887910,"sku":"EASDCLPSP40L","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCLPSP_main.png?v=1775691733"},{"product_id":"eslpsmr2rc","title":"ECS-SL Pilot-Scale Multifunctional Roll-to-Roll Coater (Max. 360 mm, Doctor Balde, Reverse Comma, Slot Die, and Microgravure), ESLPSMR2RC","description":"\u003cp\u003eA high-end lab R2R coater normally offer interchangeable heads: (1) \u003cstrong\u003eSlot-Die Coating\u003c\/strong\u003e: The industry standard for high-precision battery electrodes. It uses a shim and a precision pump to \"meter\" the slurry. This is ideal for your NMP slurries as it minimizes solvent evaporation at the coating head. (2) \u003cstrong\u003eComma Doctor \/ Reverse Comma\u003c\/strong\u003e: Excellent for high-viscosity slurries. It uses a rotating \"comma\" roller to set the wet thickness. (3) \u003cstrong\u003eMicro-Gravure\u003c\/strong\u003e: Best for very thin coatings (like functional ceramic layers on separators or thin ion-exchange membranes). It uses a patterned roller to transfer a precise volume of liquid.\u003c\/p\u003e\n\u003cp\u003eGeneral Introduction of R2R coating methods:\u003c\/p\u003e\n\u003cp\u003e(1). \u003cstrong\u003eDoctor Blade Coating\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e \u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_02.png?v=1775622122\"\u003e\u003c\/p\u003e\n\u003cp\u003eIn a R2R setup, doctor blade coating is normally called Knife-over-Roll coating. It mainly consists of (1) \u003cstrong\u003eWeb\u003c\/strong\u003e: The aluminum or copper foil is pulled over a high-precision backup roller. (2) \u003cstrong\u003eReservoir\u003c\/strong\u003e: A \"dam\" of slurry is maintained just behind the blade. (3) \u003cstrong\u003eMetering\u003c\/strong\u003e: As the foil moves, the blade (the \"knife\") scrapes off excess slurry. The thickness of the wet coating is determined by the gap between the blade edge and the foil surface. The wet thickness T= Gap * K (where K is a factor, that is usually around 0.5 to 0.7, depending on the slurry's viscosity and the web speed.)\u003c\/p\u003e\n\u003cp\u003e(2). \u003cstrong\u003eReverse Comma Coating (also called Transfer Comma Coating)\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cimg height=\"102\" width=\"140\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_03.png?v=1775622183\"\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eUnlike a standard doctor blade where the foil moves under a stationary knife, a reverse comma system uses a three-roll or two-roll configuration to \"transfer\" a metered film of slurry onto the foil. The key components and features are: (1) \u003cstrong\u003eComma Roller\u003c\/strong\u003e: A high-precision steel cylinder with a \"comma-shaped\" cross-section. It doesn't move during the coating process; instead, it acts as a high-precision gate. (2) \u003cstrong\u003eApplicator (Back-up) Roller\u003c\/strong\u003e: This roller rotates in the opposite direction (reverse) to the web travel. It picks up the slurry from a reservoir and carries it toward the comma gap. (3) \u003cstrong\u003eTransfer\u003c\/strong\u003e: As the foil (web) passes between the rollers, the metered slurry is wiped onto the foil.\u003c\/p\u003e\n\u003cp\u003e(3). \u003cstrong\u003eSlot Die Coating\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_04.png?v=1775622901\" alt=\"\" width=\"130\" height=\"105\"\u003e\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003eWhile doctor blade and comma coating are \"metering\" methods (where you scrape off excess), slot-die is a \"pre-metered\" method. This means the exact volume of slurry pumped into the head is the exact volume that ends up on the foil. Normally slot die coating system consists of three main components: A high-precision pump (usually a syringe or gear pump), a slot-die head, and a back-up roller. The slot die coating head is mainly composed of (1)\u003cstrong\u003e Reservoir (Manifold)\u003c\/strong\u003e: The slurry is pumped into an internal cavity inside the die head designed to distribute the fluid evenly across the entire width. (2) \u003cstrong\u003eShim\u003c\/strong\u003e: A thin, precision-cut metal plate determines the width of the coating and the internal gap of the die. The coating bead is critical for the coating film quality, where the slurry emerges from a narrow \"slot\" and forms a liquid bridge (the \"bead\") between the die lips and the moving foil.\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e(3). \u003cstrong\u003eMicrogravure Coating\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\u003cstrong\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_05.png?v=1775623284\" alt=\"\" width=\"169\" height=\"96\"\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003eMicrogravure coating is a specialized roll-to-roll (R2R) technique used for extremely thin, high-precision coatings. Unlike standard gravure, which uses large rollers and a doctor blade on the foil, microgravure uses a very small diameter engraved roll that rotates in the opposite direction to the web. The R2R microgravure coating system has a small, engraved \"gravure\" roll (typically 20mm to 50mm in diameter) that is partially submerged in a slurry reservoir. There are multiple distinct features: (1) \u003cstrong\u003eEngraving Roll\u003c\/strong\u003e: The roll surface is covered in microscopic cells (patterns like honeycombs or pyramids). The \"cell volume\" determines exactly how much liquid is picked up. (2) \u003cstrong\u003eReverse Rotation\u003c\/strong\u003e: The roll rotates in the opposite direction of the foil (web). This \"kiss-coating\" action shears the liquid as it transfers, resulting in a much smoother surface than traditional gravure. (3) \u003cstrong\u003eDoctor Blade\u003c\/strong\u003e: A flexible blade scrapes the excess slurry off the roll before it touches the foil, ensuring only the liquid inside the engraved cells is transferred.\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\n\u003cstrong\u003e\u003c\/strong\u003e\u003cbr\u003e\n\u003c\/div\u003e\n\u003ctable style=\"height: 3113.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 47.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESLPSMR2RC (ESL-PSMR2RC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 47.6px;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, three phases, 50\/60Hz, 11 KW\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eAC380V±10%, three phases is available upon request\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 145.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 145.6px;\"\u003e\u003cem\u003eGeneral Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 145.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eRoller width: 400 mm (Customized roller width up to 600 mm can be supplied upon request) \u003c\/li\u003e\n\u003cli\u003eLoading substrate width: Max. 380 mm\u003c\/li\u003e\n\u003cli\u003eCoating width: Max. 360 mm\u003c\/li\u003e\n\u003cli\u003eMechanical coating speed: Max. 10 m\/min (the real coating speed depends on the slurry properties and dry oven length\/temperature)\u003c\/li\u003e\n\u003cli\u003eGuiding roller diameter: Ф60mm (anodized aluminum)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 145.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 145.6px;\"\u003e\u003cem\u003eUnwinding\/Winding Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 145.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eRoller diameter: 3\", mechanical expansion for tightening the loading roll substrate and collection cardboard. \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eMax. winding\/unwinding roll diameter: 300 mm \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eAlignment Sensors were installed and aligning position resolution could be 0.5 mm. \u003c\/li\u003e\n\u003cli\u003eCoating Roller: Stainless Steel with surface Cr coating, Ф120mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 1917.4px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 1917.4px;\"\u003e\u003cem\u003eCoating Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 1917.4px;\"\u003e\n\u003cp\u003e   (1) \u003cstrong\u003eDoctor Blade\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e            \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_06_100x100.png?v=1775625753\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe doctor blade is made of SS with surface Cr coating and its diameter is Ф100mm. \u003c\/li\u003e\n\u003cli\u003eThe coating width is 50-360 mm, which can be adjusted by the blocking foam. \u003c\/li\u003e\n\u003cli\u003eSlurry Viscosity: 2000-6000 cP (recommended, higher viscosity up to 10000-15000 cP may also work for thicker electrode).\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsflpp5l?variant=47523679863014\"\u003eEABSFLPP5L\u003c\/a\u003e can be considered (Larger tank volume (eg: 10 L, 20 L) can be supplied upon request). \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e              \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsflpp5l?variant=47523679863014\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EABSFLPP5L_main_100x100.png?v=1775689239\" alt=\"\" style=\"float: none;\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e    (2) \u003cstrong\u003eReverse Comma (Transfer Coating)\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e         \u003c\/strong\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESLPSMR2RC_03_100x100.png?v=1775699889\" alt=\"\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe coating roller is made of SS with surface Cr coating and its diameter is Ф120mm. \u003c\/li\u003e\n\u003cli\u003eThe backing roller is made of rubber (Ф120mm, pneumatic)\u003c\/li\u003e\n\u003cli\u003eThe comma bar is made of SS with surface Cr coating and its diameter is Ф100mm.\u003c\/li\u003e\n\u003cli\u003eThe coating width is 50-360 mm, which can be adjusted by the blocking foam. \u003c\/li\u003e\n\u003cli\u003eSlurry Viscosity: 2000-12000 cP (recommended)\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsflpp5l?variant=47523679863014\"\u003eEABSFLPP5L\u003c\/a\u003e\u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003e\u003c\/a\u003e can be considered. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e    (3) \u003cstrong\u003eSlot Die \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e        \u003c\/strong\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMMR2RC_05_100x100.png?v=1775688285\" alt=\"\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe coating roller is made of SS with surface Cr coating and its diameter is Ф120mm. \u003c\/li\u003e\n\u003cli\u003eThe coating width is 50-360 mm, which can be adjusted by the opening mouth of shims. The standard shim thickness is 0.2, 0.3, 0.4, 0.5mm. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_09_100x100.png?v=1775630854\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry Viscosity: 50-12000 cP. For battery application, slurry viscosity is recommended in 2000-8000 cP. \u003c\/li\u003e\n\u003cli\u003eThe precise screw pump \u003ca href=\"https:\/\/echemsupplies.com\/products\/easdclpsp?variant=47523778822374\"\u003eEASDCLPSP\u003c\/a\u003e is the best option for stable slot die coating.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCLPSP_main_100x100.png?v=1775691733\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFor intermittent coating (or pattern coating) for cylindrical electrode application, the intermittent valve system is highly recommended. For simultaneous dual-layer coating, a customized dual-channel slot die head (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esar2rcsdh?variant=47523176710374\"\u003eESAR2RCSDH\u003c\/a\u003e) can be supplied. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_10_100x100.png?v=1775633700\"\u003e     \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_15_100x100.png?v=1775662134\" alt=\"\" style=\"float: none;\"\u003e    \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_16_100x100.png?v=1775662200\" alt=\"\" style=\"float: none;\" width=\"128\" height=\"82\"\u003e\u003c\/p\u003e\n\u003cp\u003e   (4) \u003cstrong\u003eMicrogravure\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e    \u003c\/strong\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMMR2RC_06_100x100.png?v=1775688286\" alt=\"\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eA standard microgravure rod with Ф30mm is included. The parameters, such as coating width, engraved pattern, mesh number and depth can be customized. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_12_100x100.png?v=1775634349\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry Viscosity: 20-2000 cP.\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsflpp5l?variant=47523679863014\"\u003eEABSFLPP5L\u003c\/a\u003e\u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003e\u003c\/a\u003e can be considered. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 331.8px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 331.8px;\"\u003e\u003cem\u003eHeating Oven Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 331.8px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eHeating mode: Convection heating (hot air flow). Other heating methods of IR and UV can be customized upon request. Various heating modules are switchable.\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003eHeating temperature: Max.150℃\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003eStandard heating oven length: 4.5 m (1.5 m\/each, three heating chambers). More heating chambers can be integrated to increase the coating\/drying speed. \u003c\/li\u003e\n\u003cli\u003eThe multiple heating chamber can be used to build temperature-gradient for coating layer drying and obtain high quality battery electrodes. \u003c\/li\u003e\n\u003cli\u003eVentilation: air flow: 570m³\/h, 6\" aluminum pipe\u003c\/li\u003e\n\u003cli\u003eNMP recycler can be integrated with the R2R coater to capture and recycle the NMP solvents. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 145.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 145.6px;\"\u003e\n\u003cp\u003eTension Control System\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 145.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eTension range: 10-80 N (resolution is ±3 N), which is controlled by swing roller system.\u003c\/li\u003e\n\u003cli\u003eFor low-tension substrate coating (eg: separator and membrane), the specially designed low tension version is highly recommended since its lowest tension can be down to 5 N.  \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 187.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 187.6px;\"\u003e\u003ci\u003eGas Compressor\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 187.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMultiple gas compressor (\u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e) is needed to provide 60-80 psi for pneumatic operation.\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EUQOFGC_main_100x100.png?v=1775414665\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 86.8px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 86.8px;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 86.8px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 10px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 10px;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 10px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL3550 * W1200 * H2000 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 47.6px;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~1.5 T\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0255270112001997\"\u003eM. Schmitt, et al., Slot-die processing of lithium-ion battery electrodes—Coating window characterization, Chemical Engineering and Processing: Process Intensification, 2013, 68, 32-37\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1088\/1361-6463\/aafbf3\/meta\"\u003eH. Li, et al., High-performance supercapacitor carbon electrode fabricated by large-scale roll-to-roll micro-gravure printing,  J. Phys. D: Appl. Phys., 2019, 52, 115501\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s40095-022-00481-w\"\u003eL. A. Román-Ramírez, et al., Effect of coating operating parameters on electrode physical characteristics and final electrochemical performance of lithium-ion batteries, International Journal of Energy and Environmental Engineering, 2022, 13, 943-953\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Doctor Blade","offer_id":47523803398374,"sku":"ESLPSMR2RCDB","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Reverse Comma","offer_id":47523803431142,"sku":"ESLPSMR2RCRC","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Slot Die","offer_id":47523803463910,"sku":"ESLPSMR2RCSD","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Microgravure","offer_id":47523803496678,"sku":"ESLPSMR2RCMG","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Blade + Slot Die","offer_id":47523803529446,"sku":"ESLPSMR2RCBSD","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Reverse Comma + Slot Die","offer_id":47523803562214,"sku":"ESLPSMR2RCRCSD","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Blade + Reverse Comma + Slot Die","offer_id":47523803594982,"sku":"ESLPSMR2RCBRCSD","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESLPSMR2RC_main.png?v=1775696971"},{"product_id":"esmmr2rcdhc","title":"ECS-SM Multifunctional Roll-to-Roll Coater (Max. 260 mm, Doctor Balde, Reverse Comma, Slot Die, and Microgravure) with Dual Heating Chambers, ESMMR2RCDHC","description":"\u003cp\u003eA high-end lab R2R coater normally offer interchangeable heads: (1) \u003cstrong\u003eSlot-Die Coating\u003c\/strong\u003e: The industry standard for high-precision battery electrodes. It uses a shim and a precision pump to \"meter\" the slurry. This is ideal for your NMP slurries as it minimizes solvent evaporation at the coating head. (2) \u003cstrong\u003eComma Doctor \/ Reverse Comma\u003c\/strong\u003e: Excellent for high-viscosity slurries. It uses a rotating \"comma\" roller to set the wet thickness. (3) \u003cstrong\u003eMicro-Gravure\u003c\/strong\u003e: Best for very thin coatings (like functional ceramic layers on separators or thin ion-exchange membranes). It uses a patterned roller to transfer a precise volume of liquid.\u003c\/p\u003e\n\u003cp\u003eGeneral Introduction of R2R coating methods:\u003c\/p\u003e\n\u003cp\u003e(1). \u003cstrong\u003eDoctor Blade Coating\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_02.png?v=1775622122\" alt=\"\"\u003e\u003c\/p\u003e\n\u003cp\u003eIn a R2R setup, doctor blade coating is normally called Knife-over-Roll coating. It mainly consists of (1) \u003cstrong\u003eWeb\u003c\/strong\u003e: The aluminum or copper foil is pulled over a high-precision backup roller. (2) \u003cstrong\u003eReservoir\u003c\/strong\u003e: A \"dam\" of slurry is maintained just behind the blade. (3) \u003cstrong\u003eMetering\u003c\/strong\u003e: As the foil moves, the blade (the \"knife\") scrapes off excess slurry. The thickness of the wet coating is determined by the gap between the blade edge and the foil surface. The wet thickness T= Gap * K (where K is a factor, that is usually around 0.5 to 0.7, depending on the slurry's viscosity and the web speed.)\u003c\/p\u003e\n\u003cp\u003e(2). \u003cstrong\u003eReverse Comma Coating (also called Transfer Comma Coating)\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_03.png?v=1775622183\" alt=\"\" width=\"140\" height=\"102\"\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eUnlike a standard doctor blade where the foil moves under a stationary knife, a reverse comma system uses a three-roll or two-roll configuration to \"transfer\" a metered film of slurry onto the foil. The key components and features are: (1) \u003cstrong\u003eComma Roller\u003c\/strong\u003e: A high-precision steel cylinder with a \"comma-shaped\" cross-section. It doesn't move during the coating process; instead, it acts as a high-precision gate. (2) \u003cstrong\u003eApplicator (Back-up) Roller\u003c\/strong\u003e: This roller rotates in the opposite direction (reverse) to the web travel. It picks up the slurry from a reservoir and carries it toward the comma gap. (3) \u003cstrong\u003eTransfer\u003c\/strong\u003e: As the foil (web) passes between the rollers, the metered slurry is wiped onto the foil.\u003c\/p\u003e\n\u003cp\u003e(3). \u003cstrong\u003eSlot Die Coating\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\u003cimg height=\"105\" width=\"130\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_04.png?v=1775622901\"\u003e\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003eWhile doctor blade and comma coating are \"metering\" methods (where you scrape off excess), slot-die is a \"pre-metered\" method. This means the exact volume of slurry pumped into the head is the exact volume that ends up on the foil. Normally slot die coating system consists of three main components: A high-precision pump (usually a syringe or gear pump), a slot-die head, and a back-up roller. The slot die coating head is mainly composed of (1)\u003cstrong\u003e Reservoir (Manifold)\u003c\/strong\u003e: The slurry is pumped into an internal cavity inside the die head designed to distribute the fluid evenly across the entire width. (2) \u003cstrong\u003eShim\u003c\/strong\u003e: A thin, precision-cut metal plate determines the width of the coating and the internal gap of the die. The coating bead is critical for the coating film quality, where the slurry emerges from a narrow \"slot\" and forms a liquid bridge (the \"bead\") between the die lips and the moving foil.\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e(3). \u003cstrong\u003eMicrogravure Coating\u003c\/strong\u003e\n\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\u003cstrong\u003e\u003cimg height=\"96\" width=\"169\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_05.png?v=1775623284\"\u003e\u003c\/strong\u003e\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003eMicrogravure coating is a specialized roll-to-roll (R2R) technique used for extremely thin, high-precision coatings. Unlike standard gravure, which uses large rollers and a doctor blade on the foil, microgravure uses a very small diameter engraved roll that rotates in the opposite direction to the web. The R2R microgravure coating system has a small, engraved \"gravure\" roll (typically 20mm to 50mm in diameter) that is partially submerged in a slurry reservoir. There are multiple distinct features: (1) \u003cstrong\u003eEngraving Roll\u003c\/strong\u003e: The roll surface is covered in microscopic cells (patterns like honeycombs or pyramids). The \"cell volume\" determines exactly how much liquid is picked up. (2) \u003cstrong\u003eReverse Rotation\u003c\/strong\u003e: The roll rotates in the opposite direction of the foil (web). This \"kiss-coating\" action shears the liquid as it transfers, resulting in a much smoother surface than traditional gravure. (3) \u003cstrong\u003eDoctor Blade\u003c\/strong\u003e: A flexible blade scrapes the excess slurry off the roll before it touches the foil, ensuring only the liquid inside the engraved cells is transferred.\u003c\/div\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\n\u003cstrong\u003e\u003c\/strong\u003e\u003cbr\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\" style=\"height: 3113.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 47.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESMMR2RCDHC (ESM-MR2RC-DHC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 47.6px;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC380V±10%, three-phases, 50\/60Hz, 11 k W\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 145.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 145.6px;\"\u003e\u003cem\u003eGeneral Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 145.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eRoller width: 300 mm \u003c\/li\u003e\n\u003cli\u003eLoading substrate width: Max. 280 mm\u003c\/li\u003e\n\u003cli\u003eCoating width: Max. 260 mm\u003c\/li\u003e\n\u003cli\u003eMechanical coating speed: 0.01-2.0m\/min (the real coating speed depends on the slurry properties and dry oven length\/temperature)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 145.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 145.6px;\"\u003e\u003cem\u003eUnwinding\/Winding Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 145.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eRoller diameter: 3\", mechanical expansion for tightening the loading roll substrate and collection cardboard. \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eMax. winding\/unwinding roll diameter: 250 mm \u003c\/li\u003e\n\u003cli\u003eAlignment Sensors were installed and aligning position resolution could be 0.5 mm. \u003c\/li\u003e\n\u003cli\u003eCoating Roller: Stainless Steel with surface Cr coating, Ф100mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 1917.4px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 1917.4px;\"\u003e\u003cem\u003eCoating Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 1917.4px;\"\u003e\n\u003cp\u003e   (1) \u003cstrong\u003eDoctor Blade\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e            \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_06_100x100.png?v=1775625753\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe doctor blade is made of SS with surface Cr coating and its diameter is Ф100mm. \u003c\/li\u003e\n\u003cli\u003eThe coating width is 0-260 mm, which can be adjusted by the blocking foam. \u003c\/li\u003e\n\u003cli\u003eSlurry Viscosity: 2000-6000 cP (recommended, higher viscosity up to 10000-15000 cP may also work for thicker electrode).\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003eEABSFPP2L\u003c\/a\u003e or \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsflpp5l?variant=47523679863014\"\u003eEABSFLPP5L\u003c\/a\u003e can be considered. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EABSFPP2L_main_100x100.png?v=1775628781\"\u003e    \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsflpp5l?variant=47523679863014\"\u003e\u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EABSFLPP5L_main_100x100.png?v=1775689239\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e    (2) \u003cstrong\u003eReverse Comma (Transfer Coating)\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e         \u003c\/strong\u003e\u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_07_100x100.png?v=1775627010\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe coating roller is made of SS with surface Cr coating and its diameter is Ф100mm. \u003c\/li\u003e\n\u003cli\u003eThe backing roller is made of rubber (Ф100mm, pneumatic)\u003c\/li\u003e\n\u003cli\u003eThe comma bar is made of SS with surface Cr coating and its diameter is Ф100mm.\u003c\/li\u003e\n\u003cli\u003eThe coating width is 0-260 mm, which can be adjusted by the blocking foam. \u003c\/li\u003e\n\u003cli\u003eSlurry Viscosity: 2000-12000 cP (recommended)\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003eEABSFPP2L\u003c\/a\u003e can be considered. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e    (3) \u003cstrong\u003eSlot Die \u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e        \u003c\/strong\u003e\u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMMR2RC_05_100x100.png?v=1775688285\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe coating roller is made of SS with surface Cr coating and its diameter is Ф100mm. \u003c\/li\u003e\n\u003cli\u003eThe coating width is 0-260 mm, which can be adjusted by the opening mouth of shims. The standard shim thickness is 0.2, 0.3, 0.4, 0.5mm. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_09_100x100.png?v=1775630854\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry Viscosity: 50-12000 cP. For battery application, slurry viscosity is recommended in 2000-8000 cP. \u003c\/li\u003e\n\u003cli\u003eThe precise screw pump \u003ca href=\"https:\/\/echemsupplies.com\/products\/easdcpsp?variant=47522239578342\"\u003eEASDCPSP\u003c\/a\u003e is the best option for stable slot die coating.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003ca href=\"https:\/\/echemsupplies.com\/products\/easdcpsp?variant=47522239578342\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EASDCPSP_main_100x100.png?v=1775632530\" alt=\"\" style=\"float: none;\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFor intermittent coating (or pattern coating) for cylindrical electrode application, the intermittent valve system is highly recommended. For simultaneous dual-layer coating, a customized dual-channel slot die head (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esar2rcsdh?variant=47523176710374\"\u003eESAR2RCSDH\u003c\/a\u003e) can be supplied. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_10_100x100.png?v=1775633700\" alt=\"\" style=\"float: none;\"\u003e     \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_15_100x100.png?v=1775662134\"\u003e    \u003cimg height=\"82\" width=\"128\" style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_16_100x100.png?v=1775662200\"\u003e\u003c\/p\u003e\n\u003cp\u003e   (4) \u003cstrong\u003eMicrogravure\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e    \u003c\/strong\u003e\u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMMR2RC_06_100x100.png?v=1775688286\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eA standard microgravure rod with Ф30mm is included. The parameters, such as coating width, engraved pattern, mesh number and depth can be customized. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMR2RC_12_100x100.png?v=1775634349\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry Viscosity: 20-2000 cP.\u003c\/li\u003e\n\u003cli\u003eThe slurry feeder \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003eEABSFPP2L\u003c\/a\u003e can be considered. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 331.8px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 331.8px;\"\u003e\u003cem\u003eHeating Oven Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 331.8px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eHeating modes: \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e       (1) Convection Heating + Convection Heating (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003estandard version\u003c\/span\u003e)\u003c\/p\u003e\n\u003cp\u003e       (2) Convection Heating + IR Heating (\u003cstrong\u003eCustomized\u003c\/strong\u003e)\u003c\/p\u003e\n\u003cp\u003e       (3) Convection Heating + UV Curing (\u003cstrong\u003eCustomized\u003c\/strong\u003e)\u003c\/p\u003e\n\u003cp\u003e       (4) IR Heating + IR Heating (\u003cstrong\u003eCustomized\u003c\/strong\u003e)\u003c\/p\u003e\n\u003cp\u003e       (5) UV Curing + UV Curing (\u003cstrong\u003eCustomized\u003c\/strong\u003e)\u003c\/p\u003e\n\u003cp\u003e       (6) IR Heating + UV Curing (\u003cstrong\u003eCustomized\u003c\/strong\u003e)\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eHeating Temperature (Convection\/IR): Max.150℃\u003c\/li\u003e\n\u003cli\u003eThe UV intensity should be determined by customers. \u003c\/li\u003e\n\u003cli\u003eHeating oven length: 0.8 m\u003c\/li\u003e\n\u003cli\u003eVentilation: air flow: 570m³\/h (two blowers), 5\" aluminum pipe\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 145.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 145.6px;\"\u003e\n\u003cp\u003eTension Control System\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 145.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eTension range: 10-60 N (resolution is ±3 N), which is controlled by swing roller system.\u003c\/li\u003e\n\u003cli\u003eFor low-tension substrate coating (eg: separator and membrane), the specially designed low tension version is highly recommended since its lowest tension can be down to 5 N.  \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 187.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 187.6px;\"\u003e\u003ci\u003eGas Compressor\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 187.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA gas compressor (\u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e) is needed to provide 60-80 psi for pneumatic operation.\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EUQOFGC_main_100x100.png?v=1775414665\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 86.8px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 86.8px;\"\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 86.8px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 10px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 10px;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 10px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL2700 * W970 * H1300 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 22.6619%; height: 47.6px;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 76.9784%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~1300 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0255270112001997\"\u003eM. Schmitt, et al., Slot-die processing of lithium-ion battery electrodes—Coating window characterization, Chemical Engineering and Processing: Process Intensification, 2013, 68, 32-37\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1088\/1361-6463\/aafbf3\/meta\"\u003eH. Li, et al., High-performance supercapacitor carbon electrode fabricated by large-scale roll-to-roll micro-gravure printing,  J. Phys. D: Appl. Phys., 2019, 52, 115501\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s40095-022-00481-w\"\u003eL. A. Román-Ramírez, et al., Effect of coating operating parameters on electrode physical characteristics and final electrochemical performance of lithium-ion batteries, International Journal of Energy and Environmental Engineering, 2022, 13, 943-953\u003c\/a\u003e. \u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Doctor Blade (Dual Convection)","offer_id":47524633575654,"sku":"ESMMR2RCDHCDB","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Reverse Comma (Dual Convection)","offer_id":47524633608422,"sku":"ESMMR2RCDHCRC","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Slot Die (Dual Convection)","offer_id":47524633641190,"sku":"ESMMR2RCDHCSD","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Microgravure (Dual Convection)","offer_id":47524633673958,"sku":"ESMMR2RCDHCMG","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Blade + Slot Die (Dual Convection)","offer_id":47524633706726,"sku":"ESMMR2RCDHCBSD","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Reverse Comma + Slot Die (Dual Convection)","offer_id":47524633739494,"sku":"ESMMR2RCDHCRCSD","price":8888888.0,"currency_code":"USD","in_stock":true},{"title":"Blade + Reverse Comma + Slot Die (Dual Convection)","offer_id":47524633772262,"sku":"ESMMR2RCDHCBRCSD","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMMR2RCDHC_main.png?v=1775708161"},{"product_id":"esmr2rdc","title":"ECS-SM Roll-to-Roll Dip Coater (Max. 280 mm) with Metering Wire Rod and IR Heating, ESMR2RDC","description":"\u003cp\u003eA Roll-to-Roll (R2R) Dip Coater is a classic \"immersion\" coating system where the substrate (web) is passed through a liquid bath to be coated on both sides simultaneously. While Slot-Die and Doctor Blade coating are preferred for primary electrodes, dip coating is a vital process in your research for functionalizing separators and fabricating ion-exchange membranes where full saturation or double-sided application is required.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\n\u003cp\u003eIn a R2R dip coater, the foil or membrane is guided into a reservoir (dip tank) by a series of rollers. (1)\u003cstrong\u003e Immersion\u003c\/strong\u003e: The web travels down into the coating fluid. (2) \u003cstrong\u003ePick-up\u003c\/strong\u003e: As it emerges vertically, a liquid film adheres to both sides of the substrate. (3) \u003cstrong\u003eMetering (The Landau-Levich Regime)\u003c\/strong\u003e: The final thickness is determined primarily by the withdrawal speed and the viscosity of the fluid. (4) \u003cstrong\u003eDoctoring (Optional)\u003c\/strong\u003e: Many R2R dip coaters include \"Air Knives\" or \"Squeeze Rollers\" at the exit of the tank to blow off or press out excess liquid to achieve a specific target thickness.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMR2RDC_02.png?v=1775712442\" alt=\"\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESMR2RDC (ESM-R2RDC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 3000 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eGeneral Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eRoller width: 300 mm \u003c\/li\u003e\n\u003cli\u003eLoading substrate width: Max. 280 mm\u003c\/li\u003e\n\u003cli\u003eCoating width: Max. 280 mm\u003c\/li\u003e\n\u003cli\u003eMechanical coating speed: 0.05-0.75m\/min (the real coating speed depends on the slurry properties and dry oven length\/temperature)\u003c\/li\u003e\n\u003cli\u003eThe general design drawing is shown below:\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMR2RDC_03_160x160.png?v=1775717717\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eUnwinding\/Winding Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eRoller diameter: 3\", mechanical expansion for tightening the loading roll substrate and collection cardboard. \u003c\/li\u003e\n\u003cli\u003eMax. winding\/unwinding roll diameter: 300 mm \u003c\/li\u003e\n\u003cli\u003eAlignment Sensors were installed and aligning position resolution could be ±0.3-0.5 mm. \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDip Coating Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry Container Size: 0.3 L (0.7 L and 2.7 L can be supplied upon request)\u003c\/li\u003e\n\u003cli\u003eSlurry Viscosity: 50-500 cP (Recommended).\u003c\/li\u003e\n\u003cli\u003eThe peristaltic pump \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003eEABSFPP2L\u003c\/a\u003e can be supplied as slurry feeder for the dip coating. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EABSFPP2L_main_100x100.png?v=1775628781\"\u003e         \u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMetering Wire Rod\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAfter dip coating, the wet coating film will go through the metering wire rods and obtain desirable thickness. \u003c\/li\u003e\n\u003cli\u003eThe standard wire rod (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esmawrw300?variant=47525192040678\"\u003eESMAWRW300\u003c\/a\u003e) is D10 mm, effective coating length is 300 mm, and groove \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            \u003ca href=\"https:\/\/echemsupplies.com\/products\/esmawrw300?variant=47525192040678\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMAWRW300_main_100x100.png?v=1775718854\" alt=\"\" style=\"float: none;\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eHeating Oven Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eHeating mode: IR heating (carbon fiber), 2 kW.\u003c\/li\u003e\n\u003cli\u003eHeating chamber length: 0.5 m\u003c\/li\u003e\n\u003cli\u003eHeating temperature: Max.150℃\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eVentilation: centrifugal blower, air flow: 330m³\/h (adjustable), 3\" aluminum pipe\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003eTension Control System\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eTension range: 10-60 N (resolution is ±3 N), which is controlled by swing roller system.\u003c\/li\u003e\n\u003cli\u003eFor low-tension substrate coating (eg: separator and membrane), the specially designed low tension version is highly recommended since its lowest tension can be down to 5 N.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eGas Compressor\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eA gas compressor (\u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e) is needed to provide 60-80 psi for pneumatic operation.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EUQOFGC_main_100x100.png?v=1775414665\" alt=\"\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL980 * W750 * H1420 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~580 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0376738818305684\"\u003eM. Cook, et al., Roll-to-roll dip coating of three different PIMs for Organic Solvent Nanofiltration, Journal of Membrane Science, 2018, 558, 52-63\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1143\/JJAP.44.L126\/meta\"\u003eK. Fujimoto, et al., Fabrication of Layer-by-Layer Self-Assembly Films Using Roll-to-Roll Process, Jpn. J. Appl. Phys., 2005, 44, L126\u003c\/a\u003e\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47524834803942,"sku":"ESMR2RDC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMR2RDC_main.png?v=1775711266"},{"product_id":"esmawrw300","title":"Wire Rod (W=300 mm, D=10 mm) for Roll-to-Roll Dip Coater (ESMR2RDC), ESMAWRW300","description":"\u003cp\u003eWire Rod (or Mayer Rod) is a popular alternative to the doctor blade, especially when you need to coat thin, high-uniformity films on flexible substrates like battery foils or membranes. While a doctor blade relies on a mechanical gap, the wire rod uses the grooves between tightly wound stainless steel wires to meter the amount of slurry that passes through.\u003c\/p\u003e\n\u003cp\u003eThe wire rod with coating width of 300 mm is specially designed as accessories for the multifunctional tap casting coater (ESMR2RDC) \u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESMAWRW300 (ESM-A-WRW300)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eEffective Coating Width\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eWire Rod: 300 um, \u003c\/li\u003e\n\u003cli\u003eDiameter: 10 mm\u003c\/li\u003e\n\u003cli\u003eSS304 material (SS316 can be supplied upon request) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eWire Groove Sizes\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e6 um, 8 um, 10 um, 12 um, 15 um, 20 um, 25 um, 30 um, 40 um, 50 um, 60 um, 80 um, 100 um, 150 um, and 200 um\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eNote\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eIt is an accessory for the roll-to-roll dip coater (ESMR2RDC) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775307026584\"\u003eA. M. Kannan, et al., Wire rod coating process of gas diffusion layers fabrication for proton exchange membrane fuel cells, J. Power Sources, 2008, 178, 231-237\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.9b15866\"\u003eL. Zeng, et al., Integrated Paper-Based Flexible Li-Ion Batteries Made by a Rod Coating Method, ACS Appl. Mater. Interfaces 2019, 11, 50, 46776–46782\u003c\/a\u003e\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"6 um","offer_id":47525192040678,"sku":"ESMAWRW300G6","price":299.0,"currency_code":"USD","in_stock":true},{"title":"8 um","offer_id":47525192073446,"sku":"ESMAWRW300G8","price":299.0,"currency_code":"USD","in_stock":true},{"title":"10 um","offer_id":47525192106214,"sku":"ESMAWRW300G10","price":299.0,"currency_code":"USD","in_stock":true},{"title":"12 um","offer_id":47525192138982,"sku":"ESMAWRW300G12","price":299.0,"currency_code":"USD","in_stock":true},{"title":"15 um","offer_id":47525192171750,"sku":"ESMAWRW300G15","price":299.0,"currency_code":"USD","in_stock":true},{"title":"20 um","offer_id":47525192204518,"sku":"ESMAWRW300G20","price":299.0,"currency_code":"USD","in_stock":true},{"title":"25 um","offer_id":47525192237286,"sku":"ESMAWRW300G25","price":299.0,"currency_code":"USD","in_stock":true},{"title":"30 um","offer_id":47525192270054,"sku":"ESMAWRW300G30","price":299.0,"currency_code":"USD","in_stock":true},{"title":"40 um","offer_id":47525192302822,"sku":"ESMAWRW300G40","price":299.0,"currency_code":"USD","in_stock":true},{"title":"50 um","offer_id":47525192335590,"sku":"ESMAWRW300G50","price":299.0,"currency_code":"USD","in_stock":true},{"title":"60 um","offer_id":47525192368358,"sku":"ESMAWRW300G60","price":299.0,"currency_code":"USD","in_stock":true},{"title":"80 um","offer_id":47525192401126,"sku":"ESMAWRW300G80","price":299.0,"currency_code":"USD","in_stock":true},{"title":"100 um","offer_id":47525192433894,"sku":"ESMAWRW300G100","price":299.0,"currency_code":"USD","in_stock":true},{"title":"150 um","offer_id":47525192466662,"sku":"ESMAWRW300G150","price":299.0,"currency_code":"USD","in_stock":true},{"title":"200 um","offer_id":47525192499430,"sku":"ESMAWRW300G200","price":299.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMAWRW300_main.png?v=1775718854"},{"product_id":"eapdtg","title":"Precise Digital Thickness Gauge (Range: 0-12.7 mm, Resolution: 0.001 mm) for Electrode Measurement, EAPDTG","description":"\u003cp\u003eIn battery research, a Precise Digital Thickness Gauge is a primary tool for quality control. It is used to verify the \"Mass Loading\" of your electrodes and to ensure your R2R Coater and Calendering steps are meeting their target specifications.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEAPDTG (E-A-PDTG)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eRange\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0-12.7 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eResolution\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.001 mm (1 um)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eTolerance\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e±0.005mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDiameter of Measurement Head\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e10 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eMeasurement Depth\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e120 mm (convenient for width substrate coating measurement)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~L 190mm* W 150mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0013468612005270\"\u003eH. Zheng, et al., A comprehensive understanding of electrode thickness effects on the electrochemical performances of Li-ion battery cathodes, Electrochimica Acta, 2012, 71, 258-265\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/advanced.onlinelibrary.wiley.com\/doi\/abs\/10.1002\/aenm.201901457\"\u003eY. Kuang, et al.,Thick Electrode Batteries: Principles, Opportunities, and Challenges, Adv Energy Mater. 2019, 9, 1901457\u003c\/a\u003e\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47525276418278,"sku":"EAPDTG","price":179.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EAPDTG_main.png?v=1775720487"},{"product_id":"ess6pdcihs","title":"ECS-SS 6-Positions Dip Coater with Independent Heating (80℃) and Stirring, ESS6PDCIHS","description":"\u003cp\u003eA 6-position dip coater with independent heating is a high-throughput laboratory instrument designed for the precise fabrication of thin films via the sol-gel process or layer-by-layer (LbL) assembly.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eThe system typically consists of a high-precision vertical lift, a rotating carousel holding six positions, and specialized heating elements. (1) \u003cstrong\u003eMulti-Position Carousel\u003c\/strong\u003e: The 6-position design allows you to hold up to six different beakers. This is ideal for complex multilayer structures where you alternate between active materials, binders, and rinsing solutions. (2) \u003cstrong\u003eIndependent Heating\u003c\/strong\u003e: Each of the six positions is equipped with its own PID-controlled heater. This allows you to maintain one solution at room temperature (e.g., a volatile solvent) while heating another (e.g., a viscous YSZ precursor) to reduce its viscosity or trigger a specific chemical reaction. (3) \u003cstrong\u003eProgrammable Logic\u003c\/strong\u003e: You can define a complex sequence: (a) \u003cem\u003eDipping Speed\u003c\/em\u003e: Controls the initial wet film thickness. (b) \u003cem\u003eDwelling Time\u003c\/em\u003e: Time the substrate stays submerged. (c) \u003cem\u003eWithdrawal Speed\u003c\/em\u003e: The most critical factor for final dry film thickness. (4) \u003cem\u003eDrying\/Curing Time\u003c\/em\u003e: The substrate can be held above the heated beaker to accelerate solvent evaporation.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESS6PDCIHS (ESS-6PDCIHS)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 1200 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eStirring Speed: 60-300 rpm (independent setting)  \u003c\/li\u003e\n\u003cli\u003eWithdraw Speed: 1-400 mm\/min (automatic); 1-150 mm\/min (manual)\u003c\/li\u003e\n\u003cli\u003eWithdraw Times: 1-45 times\u003c\/li\u003e\n\u003cli\u003eDip Coating\/Drying Times: 1-999 s\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: 1-80 mm\u003c\/li\u003e\n\u003cli\u003e Beaker Volume: 150 mL\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: 75mm×25mm×2mm\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: 60 mm\u003c\/li\u003e\n\u003cli\u003eHeating Temperature: Max. 80℃ (independent control)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL260 * W340 * H1420 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~15 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550128292070,"sku":"ESS6PDCIHS","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_main.png?v=1776528915"},{"product_id":"essa5pdcdo","title":"ECS-SS Automatic 5-Positions Dip Coater with Drying Oven (100℃), ESSA5PDCDO","description":"\u003cp\u003eAn automatic 5-position dip coater with drying oven is a high-throughput laboratory instrument designed for the precise fabrication of thin films via the sol-gel process or layer-by-layer (LbL) assembly.\u003c\/p\u003e\n\u003cdiv style=\"text-align: start;\" data-path-to-node=\"5\"\u003e\n\u003cp\u003eThe system typically consists of a high-precision vertical lift, a rotating carousel holding six positions, and specialized heating elements. (1) \u003cstrong\u003eMulti-Position Carousel\u003c\/strong\u003e: The 6-position design allows you to hold up to six different beakers. This is ideal for complex multilayer structures where you alternate between active materials, binders, and rinsing solutions. (2) \u003cstrong\u003eIndependent Heating\u003c\/strong\u003e: Each of the six positions is equipped with its own PID-controlled heater. This allows you to maintain one solution at room temperature (e.g., a volatile solvent) while heating another (e.g., a viscous YSZ precursor) to reduce its viscosity or trigger a specific chemical reaction. (3) \u003cstrong\u003eProgrammable Logic\u003c\/strong\u003e: You can define a complex sequence: (a) \u003cem\u003eDipping Speed\u003c\/em\u003e: Controls the initial wet film thickness. (b) \u003cem\u003eDwelling Time\u003c\/em\u003e: Time the substrate stays submerged. (c) \u003cem\u003eWithdrawal Speed\u003c\/em\u003e: The most critical factor for final dry film thickness. (4) \u003cem\u003eDrying\/Curing Time\u003c\/em\u003e: The substrate can be held above the heated beaker to accelerate solvent evaporation.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg style=\"float: none;\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESSA5PDCDO (ESS-A5PDCDO)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 2200 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: 1-200 mm\/min  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: 1-75 mm\u003c\/li\u003e\n\u003cli\u003eDipping Times; 1-20 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ≤60 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: L75mm×W25mm×T2.5mm\u003c\/li\u003e\n\u003cli\u003eBeaker Volume: Φ60 150ml (5 different dipping solutions)\u003c\/li\u003e\n\u003cli\u003eHeating Temperature: Max. 100℃ (independent PID control), heating time: 0-9999 min, 0.8 kW\u003c\/li\u003e\n\u003cli\u003eHeating Chamber Inner Sizes: 310mm×310mm×310mm (30L) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL455 * W500 * H1000 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~60 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550565581030,"sku":"ESSA5PDCDO","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSA5PDCDO_main.png?v=1776535206"},{"product_id":"essmsdcdo","title":"ECS-SS Micro-Speed (1-500um\/s) Dip Coater with Drying Oven (100℃), ESSMSDCDO","description":"\u003cp\u003eA Micro-Speed Dip Coater with Drying Oven is a specialized thin-film fabrication unit designed for research where ultra-thin, uniform coatings are required from low-viscosity solutions or slurries.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003e\u003cstrong\u003eMicro-Speed Drive\u003c\/strong\u003e: Unlike standard coaters, a micro-speed unit uses high-resolution stepper motors or piezo-drives to achieve withdrawal speeds as low as 0.1 um\/s. This is essential for the \"Capillary Regime\" of coating, where the film thickness is extremely thin (\u0026lt;100 nm). (2) \u003cstrong\u003eIntegrated Oven\u003c\/strong\u003e: The heating chamber is typically positioned above the dipping beaker. As the substrate is withdrawn, it enters a temperature-controlled environment (up to 200°C or higher). (a) \u003cem\u003eSolvent Management\u003c\/em\u003e: Immediate heating ensures that the solvent (like NMP or Terpineol) evaporates at a rate that matches the withdrawal speed, locking the particles (e.g., YSZ or GDC) in place. (b) \u003cem\u003ePre-heating\u003c\/em\u003e: Some systems allow the substrate to be pre-heated before dipping to alter the wetting behavior.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESSMSDCDO (ESS-MSDCDO)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC110V or 220V±10%, single phase, 50\/60Hz, 700 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: 1-500 um\/s  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: 1-75 mm\u003c\/li\u003e\n\u003cli\u003eDipping Times; 1-20 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ≤60 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: L75mm×W25mm×T2.5mm. Two samples can be clamped at the same time.\u003c\/li\u003e\n\u003cli\u003eBeaker Volume: Φ60 150ml\u003c\/li\u003e\n\u003cli\u003eHeating Temperature: Max. 100℃ (independent PID control), heating time: 0-9999 min, 0.8 kW\u003c\/li\u003e\n\u003cli\u003eHeating Chamber Inner Sizes: 310mm×310mm×310mm (30L) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL430 * W500 * H1000 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~50 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550611652838,"sku":"ESSMSDCDO","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMSDCDO_main.png?v=1776537039"},{"product_id":"essnsdcdo","title":"ECS-SS Nano-Speed (10-500 nm\/s) Dip Coater with Drying Oven (100℃), ESSNSDCDO","description":"\u003cp\u003eA Nano-Speed Dip Coater with Drying Oven is the most precise iteration of dip-coating technology, specifically designed for \"Bottom-Up\" nanotechnology and the fabrication of ultra-thin, highly ordered monolayers or sub-micron ceramic membranes.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eStandard dip coaters operate in the millimeter-per-minute range. A Nano-Speed unit utilizes specialized high-resolution piezo-drives or micro-stepping lead screws to achieve withdrawal speeds as low as 0.1 nm\/s to 10 nm\/s. (1) \u003cstrong\u003eEvaporation-Regime Coating\u003c\/strong\u003e: At these ultra-low speeds, the film formation is no longer governed by fluid dynamics (Landau-Levich) but by the rate of solvent evaporation at the meniscus (the \"Coffee Ring\" effect utilized for uniform coating). (2) \u003cstrong\u003eMolecular Assembly\u003c\/strong\u003e: This speed range is critical for Layer-by-Layer (LbL) assembly and the deposition of 2D materials (like graphene or MXenes) where you need to allow time for molecules to orient themselves on the substrate surface.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESSNSDCDO (ESS-NSDCDO)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC110V or 220V±10%, single phase, 50\/60Hz, 700 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e10-500 nm\/s \u003c\/span\u003e \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: 1-75 mm\u003c\/li\u003e\n\u003cli\u003eDipping Times; 1-20 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ≤60 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: L75mm×W25mm×T2.5mm. Two samples can be clamped at the same time.\u003c\/li\u003e\n\u003cli\u003eBeaker Volume: Φ60 150ml\u003c\/li\u003e\n\u003cli\u003eHeating Temperature: Max. 100℃ (independent PID control), heating time: 0-9999 min, 0.8 kW\u003c\/li\u003e\n\u003cli\u003eHeating Chamber Inner Sizes: 310mm×310mm×310mm (30L) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL430 * W500 * H1000 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~50 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550631018726,"sku":"ESSNSDCDO","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMSDCDO_main.png?v=1776537039"},{"product_id":"esmpdc","title":"ECS-SM Programmable Dip Coater (Sample: L310*W260*T5mm), ESMPDC","description":"\u003cp\u003eA Programmable Dip Coater for medium sample sizes is designed for laboratories moving beyond small coupons (like 1cm * 1cm) toward larger substrates such as planar SOFC plates or battery electrode foils (100 mm * 100 mm to 200 mm * 200 mm).\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eAs substrate size increases, the mass and surface tension forces change. A medium-sized programmable unit addresses this with: (1) \u003cstrong\u003eHigh-Torque Stepper Motors\u003c\/strong\u003e: Ensures smooth, vibration-free movement even with heavier substrates (e.g., thick Ni-YSZ porous supports). (2) \u003cstrong\u003eExtended Vertical Travel\u003c\/strong\u003e: Typically offers 200 mm to 300 mm of stroke to allow full immersion of medium-sized plates into deep beakers. (3) \u003cstrong\u003eComplex Motion Profiles\u003c\/strong\u003e: Programming isn't just about speed; you can set \"multi-dwell\" profiles where the substrate stays submerged for different durations at different depths to manage gradient coatings.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESMPDC (ESM-PDC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, single phase, 50\/60Hz, 100 W (DC24 V)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: 1-200 mm\/min  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: 1-270 mm\u003c\/li\u003e\n\u003cli\u003eDipping Times; 1-20 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ~200 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: Max. L310mm×W260mm×T5mm\u003c\/li\u003e\n\u003cli\u003eWithdraw Loading Mass: Max. 5.5 kg \u003c\/li\u003e\n\u003cli\u003eAcrylic Tank Volume: L340 * W50 * H280 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL455 * W330 * H890 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~20 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550641111270,"sku":"ESMPDC","price":4999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMPDC_main.png?v=1776540338"},{"product_id":"eslpdc","title":"ECS-SL Large Programmable Dip Coater (Sample: L310*W260*T5mm), ESLPDC","description":"\u003cp\u003eA Programmable Dip Coater for medium sample sizes is designed for laboratories moving beyond small coupons (like 1cm * 1cm) toward larger substrates such as planar SOFC plates or battery electrode foils (100 mm * 100 mm to 200 mm * 200 mm).\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eAs substrate size increases, the mass and surface tension forces change. A medium-sized programmable unit addresses this with: (1) \u003cstrong\u003eHigh-Torque Stepper Motors\u003c\/strong\u003e: Ensures smooth, vibration-free movement even with heavier substrates (e.g., thick Ni-YSZ porous supports). (2) \u003cstrong\u003eExtended Vertical Travel\u003c\/strong\u003e: Typically offers 200 mm to 300 mm of stroke to allow full immersion of medium-sized plates into deep beakers. (3) \u003cstrong\u003eComplex Motion Profiles\u003c\/strong\u003e: Programming isn't just about speed; you can set \"multi-dwell\" profiles where the substrate stays submerged for different durations at different depths to manage gradient coatings.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESLPDC (ESL-PDC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, single phase, 50\/60Hz, ~300 W (DC24 V)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: 10-1000 mm\/min  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e1-350 mm\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eDipping Times; 1-20 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ~300 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: Max. \u003cspan style=\"color: rgb(255, 42, 0);\"\u003eL640mm×W315mm×T5mm\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eWithdraw Loading Mass: Max. 5.5 kg \u003c\/li\u003e\n\u003cli\u003eAcrylic Tank Volume: L640 * W50 * H335 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL670 * W380 * H860 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~20 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550731124966,"sku":"ESLPDC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESLPDC_main.png?v=1776540845"},{"product_id":"esspdc3hzf","title":"ECS-SS Programmable Dip Coater with Three Heating Zone Furnace (1000℃), ESSPDC3HZF","description":"\u003cp\u003eA Programmable Dip Coater with a Three-Heating Zone Tube Furnace ($1000\\text{°C}$) is a sophisticated integrated system designed for the one-step fabrication and thermal processing of thin films. This setup allows you to dip-coat a substrate and then immediately lift it into a high-temperature furnace for drying, calcination, or sintering—all without exposing the \"green\" film to the ambient atmosphere or manual handling.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Lift Mechanism\u003c\/strong\u003e: A high-precision programmable motor moves the substrate vertically through the bottom of the furnace and into the precursor beaker. \u003cstrong\u003eThree-Zone Furnace\u003c\/strong\u003e: Unlike single-zone furnaces, the three-zone design (1000 °C) allows for a precise thermal gradient. The bottom zone typically kept cooler for initial solvent evaporation and stabilization, while the middle\/top zones are heated to the target sintering temperature to trigger phase formation and densification. \u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESSPDC3HZF (ESS-PDC3HZF)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, ~3000 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: Three stage with independent speed setting, 1-200 mm\/min  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTotal Traverse Distance (three zones): \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e~620 mm\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli style=\"color: rgb(0, 0, 0);\"\u003e\u003cspan style=\"color: rgb(0, 0, 0);\"\u003eFirst Low Temperature Region: 236 mm (fixed)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: rgb(0, 0, 0);\"\u003eSecond High Temperature Region: 150 mm (fixed)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan style=\"color: rgb(0, 0, 0);\"\u003eThird Cooling Region: 234 mm (fixed)\u003c\/span\u003e\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ~60 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: Max. \u003cspan style=\"color: rgb(255, 42, 0);\"\u003eL75mm×W25mm×T4mm\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eWithdraw Loading Mass: Max. 200 g\u003c\/li\u003e\n\u003cli\u003eHeating Temperature: Max. 1000℃ (RT-800℃ is recommended)\u003c\/li\u003e\n\u003cli\u003eTemperature Control Accuracy: ±1℃ (K-type thermocouple)\u003c\/li\u003e\n\u003cli\u003eFurnace Processing Tube: O.D. Φ50mm× I.D. φ45mm× L600mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL560 * W470 * H1550 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~20 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550762254566,"sku":"ESSPDC3HZF","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSPDC3HZF_main.png?v=1776545637"},{"product_id":"ess4paadc","title":"ECS-SS 4-Positions Angle-Adjustable Dip Coater, ESS4PAADC","description":"\u003cp\u003eA 4-Positions Angle-Adjustable Dip Coater is a specialized thin-film deposition system designed to overcome the limitations of standard vertical dipping. By allowing the substrate to enter the solution at a specific angle (typically 0° to 90°), this machine provides a unique method to control film thickness, meniscus behavior, and coating uniformity on both sides of a substrate.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eIn standard vertical dipping, gravity and surface tension pull the liquid straight down, often leading to a \"wedge effect\" (thicker at the bottom). Adjusting the angle changes the physics of the meniscus: (1) \u003cstrong\u003eMeniscus Control\u003c\/strong\u003e: A tilted entry changes the contact angle of the liquid on the substrate. This can help \"stretch\" the meniscus, leading to thinner and more uniform coatings at higher speeds than vertical dipping allows. (2) \u003cstrong\u003eSingle-Side Coating Bias\u003c\/strong\u003e: If a high-quality coating on one side of a Ni-YSZ support is required, dipping at an angle can change how the liquid drains off the \"back\" side compared to the \"front\" side. (3) \u003cstrong\u003eAsymmetric Substrates\u003c\/strong\u003e: For substrates with complex geometries or surface textures, an angled entry prevents air bubbles from being trapped in the pores—a common failure point in SOFC electrolyte deposition.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESS4PAADC (ESS-4PAADC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, ~800 W\u003c\/li\u003e\n\u003cli\u003eAC110V can be realized by a 1000 W transformer\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: Servo motor with guiding screw rod\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: 2 um\/s to 9 mm\/s (adjustable)  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDipping Times: 1-999 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e~75 mm\u003c\/span\u003e\u003cspan style=\"color: rgb(0, 0, 0);\"\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eFour 150 mL beakers are included. \u003c\/li\u003e\n\u003cli\u003eSample holder is show below:\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS4PAADC_02_100x100.png?v=1776577264\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL570 * W300 * H480 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~23 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550857085158,"sku":"ESS4PAADC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS4PAADC_main.png?v=1776577198"},{"product_id":"efsrcusc","title":"ECS-FS Remote-Controlled Ultrasonic Spray Coater (Max. 100*100 mm), EFSRCUSC","description":"\u003cp\u003eAn Ultrasonic Spray Coater is a high-precision thin-film deposition system that uses ultrasonic energy to atomize liquids into a fine, low-velocity mist. Unlike conventional air-pressure spray guns, which use high-velocity air to \"blast\" liquid into droplets, ultrasonic spray systems utilize piezoelectric vibrations to create a much more controlled and uniform spray.\u003c\/p\u003e\n\u003cdiv style=\"text-align: start;\" data-path-to-node=\"5\"\u003e\n\u003cp\u003eThe process starts with an ultrasonic nozzle, which contains piezoelectric transducers. (1) \u003cstrong\u003eVibration to Mist\u003c\/strong\u003e: When high-frequency electrical energy is applied, the transducers vibrate longitudinally. Liquid is introduced to the nozzle tip, where these vibrations create standing waves. When the amplitude reaches a certain threshold, the liquid \"disintegrates\" into millions of micron-sized droplets. (2) \u003cstrong\u003eLow-Velocity Plume\u003c\/strong\u003e: Because the droplets are created by vibration rather than high-pressure air, they emerge as a low-velocity mist. A very low-pressure carrier gas (usually Nitrogen or Air) is then used to shape the spray plume and direct it toward the substrate. (3) \u003cstrong\u003eDroplet Uniformity\u003c\/strong\u003e: The droplet size is determined primarily by the frequency of the nozzle (e.g., 20 kHz, 50 kHz, or 120 kHz). Higher frequencies produce smaller droplets, which are ideal for the thin, dense membranes required for YSZ or GDC electrolytes.\u003c\/p\u003e\n\u003cp\u003eThe working mechanism of an ultrasonic spray is shown below:\u003c\/p\u003e\n\u003cp\u003e\u003cimg style=\"float: none;\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSRCUSC_02_160x160.png?v=1776615216\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eEFSRCUSC (EFS-RCUSC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 1000 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eSpray Coater Features \u0026amp; Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eSpray Head Frequency: 100 KHz with concentrated type. Other frequency in 20-180 KHz are optional.  Power: 1-15 W.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSRCUSC_05_100x100.png?v=1776618793\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eContinuous Spray Amount: 0.01-50 mL\/min\u003c\/li\u003e\n\u003cli\u003eEffective Coating Width: 2-100 mm (the maximum coating area is 100*100 mm)\u003c\/li\u003e\n\u003cli\u003eSolution Feeding Accuracy: 0.1 uL\/min\u003c\/li\u003e\n\u003cli\u003eSolution Viscosity: ≤100 cps\u003c\/li\u003e\n\u003cli\u003eSolution Temperature: 1-60 °C\u003c\/li\u003e\n\u003cli\u003eAtomized Mist\/droplet Size: 10-45 um (depends on spray head frequency) \u003c\/li\u003e\n\u003cli\u003eCoating Uniformity: ≥95%\u003c\/li\u003e\n\u003cli\u003eSolution Utilization Efficiency: ≥95%\u003c\/li\u003e\n\u003cli\u003eGuiding Gas Flow Pressure: ≤0.1 MPa (the gas compressor \u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e can be considered)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMoving Rack Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eXYZ fixture enable movement in up\/down, front\/back, and left\/right directions. The cross-sectional laser for tracking is available upon request. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSRCUSC_03_100x100.png?v=1776618256\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe automatic XYZ movement is controlled by a remote controller.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSRCUSC_04_100x100.png?v=1776618522\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eHeating Plate Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eThe standard heating plate is made of porous aluminum alloy and the maximum heating temperature is \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e200°C\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eA higher temperature can be achieved by replaced with ceramic plate for coating pyrolysis (up to 800-1000\u003cspan style=\"color: rgb(0, 0, 0);\"\u003e°C\u003c\/span\u003e) \u003c\/li\u003e\n\u003cli\u003eThe vacuum suction feature is used to firmly hold the substrate during the coating process. An oilless vacuum pump \u003ca href=\"https:\/\/echemsupplies.com\/products\/esovp?variant=47512544542950\"\u003eESOVP\u003c\/a\u003e is highly recommended. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cdiv style=\"text-align: start;\"\u003e           \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSRCUSC_06_100x100.png?v=1776623311\" alt=\"\" style=\"float: none;\"\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL750 * W600 * H650 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~60 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775314007782\"\u003eH. Su, et al., Low platinum loading for high temperature proton exchange membrane fuel cell developed by ultrasonic spray coating technique, Journal of Power Sources, 2014, 267, 155-159\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.3c04208\"\u003eW. Feng, et al., Mathematical Model-Assisted Ultrasonic Spray Coating for Scalable Production of Large-Sized Solid Oxide Electrochemical Cells, ACS Appl. Mater. Interfaces 2023, 15, 26, 31430–31437\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.rsc.org\/en\/content\/articlelanding\/2025\/ee\/d4ee03893b\"\u003eS. W. Lee, et al., Ultrasonic spraying of Ce(Mn,Fe)O2 nanocatalysts onto a perovskite surface for highly efficient electrochemical CO2 reduction, Energy Environ. Sci., 2025,18, 1205-1213\u003c\/a\u003e. \u003c\/p\u003e","brand":"FSN","offers":[{"title":"Default Title","offer_id":47552087851238,"sku":"EFSRCUSC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSRCUSC_main.png?v=1776615216"},{"product_id":"efmpusc","title":"ECS-FM Programmable Ultrasonic Spray Coater (Max. 200*200 mm), EFMPUSC","description":"\u003cp\u003eAn Ultrasonic Spray Coater is a high-precision thin-film deposition system that uses ultrasonic energy to atomize liquids into a fine, low-velocity mist. Unlike conventional air-pressure spray guns, which use high-velocity air to \"blast\" liquid into droplets, ultrasonic spray systems utilize piezoelectric vibrations to create a much more controlled and uniform spray.\u003c\/p\u003e\n\u003cdiv style=\"text-align: start;\" data-path-to-node=\"5\"\u003e\n\u003cp\u003eThe process starts with an ultrasonic nozzle, which contains piezoelectric transducers. (1) \u003cstrong\u003eVibration to Mist\u003c\/strong\u003e: When high-frequency electrical energy is applied, the transducers vibrate longitudinally. Liquid is introduced to the nozzle tip, where these vibrations create standing waves. When the amplitude reaches a certain threshold, the liquid \"disintegrates\" into millions of micron-sized droplets. (2) \u003cstrong\u003eLow-Velocity Plume\u003c\/strong\u003e: Because the droplets are created by vibration rather than high-pressure air, they emerge as a low-velocity mist. A very low-pressure carrier gas (usually Nitrogen or Air) is then used to shape the spray plume and direct it toward the substrate. (3) \u003cstrong\u003eDroplet Uniformity\u003c\/strong\u003e: The droplet size is determined primarily by the frequency of the nozzle (e.g., 20 kHz, 50 kHz, or 120 kHz). Higher frequencies produce smaller droplets, which are ideal for the thin, dense membranes required for YSZ or GDC electrolytes.\u003c\/p\u003e\n\u003cp\u003eThe working mechanism of an ultrasonic spray is shown below:\u003c\/p\u003e\n\u003cp\u003e\u003cimg style=\"float: none;\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSRCUSC_02_160x160.png?v=1776615216\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eEFMPUSC (EFM-PUSC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 1500 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eSpray Coater Features \u0026amp; Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eSpray Head Frequency: 100 KHz with concentrated type. Other frequency in 20-180 KHz are optional.  Power: 1-15 W.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMPUSC_03_100x100.png?v=1776628622\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eContinuous Spray Amount: 0.01-50 mL\/min\u003c\/li\u003e\n\u003cli\u003eEffective Coating Width: 2-200 mm (the maximum coating area is 200*200 mm)\u003c\/li\u003e\n\u003cli\u003eSolution Feeding Accuracy: 0.1 uL\/min\u003c\/li\u003e\n\u003cli\u003eSolution Viscosity: ≤100 cps (solid content\u0026lt;30 wt%)\u003c\/li\u003e\n\u003cli\u003eSolution Temperature: 1-60 °C\u003c\/li\u003e\n\u003cli\u003eAtomized Mist\/droplet Size: 10-45 um (depends on spray head frequency) \u003c\/li\u003e\n\u003cli\u003eCoating Uniformity: ≥95%\u003c\/li\u003e\n\u003cli\u003eSolution Utilization Efficiency: ≥95%\u003c\/li\u003e\n\u003cli\u003eGuiding Gas Flow Pressure: ≤0.1 MPa (the gas compressor \u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e can be considered)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMoving Rack Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAutomatic movement in X and Y axis and the Z-direction is electrically adjustable. All three directions can be independently programmable. \u003c\/li\u003e\n\u003cli\u003eThe functions of solution feeding, ultrasonic spray, and bottom heating are integrated in touch screen for programmable setting.\u003c\/li\u003e\n\u003cli\u003eThe cross-sectional laser for tracking is available upon request. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eHeating Plate Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eThe standard heating plate is made of porous aluminum alloy and the maximum heating temperature is \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e300°C\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli style=\"color: rgb(0, 0, 0);\"\u003e\u003cspan style=\"color: rgb(0, 0, 0);\"\u003eThe porous ceramic heating plate (150°C) with high surface flatness for flexible ultrathin substrate can be supplied upon request\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003eA higher temperature can be achieved by replaced with stainless steel plate for coating pyrolysis (up to 500\u003cspan style=\"color: rgb(0, 0, 0);\"\u003e°C\u003c\/span\u003e) \u003c\/li\u003e\n\u003cli\u003eThe vacuum suction feature is used to firmly hold the substrate during the coating process. An oilless vacuum pump \u003ca href=\"https:\/\/echemsupplies.com\/products\/esovp?variant=47512544542950\"\u003eESOVP\u003c\/a\u003e is highly recommended. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cdiv style=\"text-align: start;\"\u003e           \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSRCUSC_06_100x100.png?v=1776623311\" alt=\"\" style=\"float: none;\"\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL800 * W500 * H700 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~120 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775314007782\"\u003eH. Su, et al., Low platinum loading for high temperature proton exchange membrane fuel cell developed by ultrasonic spray coating technique, Journal of Power Sources, 2014, 267, 155-159\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.3c04208\"\u003eW. Feng, et al., Mathematical Model-Assisted Ultrasonic Spray Coating for Scalable Production of Large-Sized Solid Oxide Electrochemical Cells, ACS Appl. Mater. Interfaces 2023, 15, 26, 31430–31437\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.rsc.org\/en\/content\/articlelanding\/2025\/ee\/d4ee03893b\"\u003eS. W. Lee, et al., Ultrasonic spraying of Ce(Mn,Fe)O2 nanocatalysts onto a perovskite surface for highly efficient electrochemical CO2 reduction, Energy Environ. Sci., 2025,18, 1205-1213\u003c\/a\u003e. \u003c\/p\u003e","brand":"FSN","offers":[{"title":"Default Title","offer_id":47553065844966,"sku":"EFMPUSC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMPUSC_main.png?v=1776626600"},{"product_id":"eflspusc","title":"ECS-FL Sealed Programmable Ultrasonic Spray Coater (Max. 300*300 mm), EFLSPUSC","description":"\u003cp\u003eAn Ultrasonic Spray Coater is a high-precision thin-film deposition system that uses ultrasonic energy to atomize liquids into a fine, low-velocity mist. Unlike conventional air-pressure spray guns, which use high-velocity air to \"blast\" liquid into droplets, ultrasonic spray systems utilize piezoelectric vibrations to create a much more controlled and uniform spray.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eThe process starts with an ultrasonic nozzle, which contains piezoelectric transducers. (1) \u003cstrong\u003eVibration to Mist\u003c\/strong\u003e: When high-frequency electrical energy is applied, the transducers vibrate longitudinally. Liquid is introduced to the nozzle tip, where these vibrations create standing waves. When the amplitude reaches a certain threshold, the liquid \"disintegrates\" into millions of micron-sized droplets. (2) \u003cstrong\u003eLow-Velocity Plume\u003c\/strong\u003e: Because the droplets are created by vibration rather than high-pressure air, they emerge as a low-velocity mist. A very low-pressure carrier gas (usually Nitrogen or Air) is then used to shape the spray plume and direct it toward the substrate. (3) \u003cstrong\u003eDroplet Uniformity\u003c\/strong\u003e: The droplet size is determined primarily by the frequency of the nozzle (e.g., 20 kHz, 50 kHz, or 120 kHz). Higher frequencies produce smaller droplets, which are ideal for the thin, dense membranes required for YSZ or GDC electrolytes.\u003c\/p\u003e\n\u003cp\u003eThe working mechanism of an ultrasonic spray is shown below:\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSRCUSC_02_160x160.png?v=1776615216\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eEFLSPUSC (EFL-SPUSC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 2000 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eSpray Coater Features \u0026amp; Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eSpray Head Frequency: 100 KHz with concentrated type. Other frequency in 20-180 KHz are optional.  Power: 1-15 W.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMPUSC_03_100x100.png?v=1776628622\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eContinuous Spray Amount: 0.01-50 mL\/min\u003c\/li\u003e\n\u003cli\u003eEffective Coating Width: 2-300 mm (the maximum coating area is 300*300 mm)\u003c\/li\u003e\n\u003cli\u003eSolution Feeding Accuracy: 0.1 uL\/min\u003c\/li\u003e\n\u003cli\u003eSolution Viscosity: ≤30 cps (solid content\u0026lt;30 wt%, depends on the ultrasonic head)\u003c\/li\u003e\n\u003cli\u003eSolution Temperature: 1-60 °C\u003c\/li\u003e\n\u003cli\u003eAtomized Mist\/droplet Size: 10-45 um (depends on spray head frequency) \u003c\/li\u003e\n\u003cli\u003eCoating Uniformity: ≥95%\u003c\/li\u003e\n\u003cli\u003eSolution Utilization Efficiency: ≥95%\u003c\/li\u003e\n\u003cli\u003eGuiding Gas Flow Pressure: ≤0.1 MPa (the gas compressor \u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e can be considered)\u003c\/li\u003e\n\u003cli style=\"color: rgb(255, 42, 0);\"\u003e\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eThe whole chamber hosting the spray coating system is fully sealed. Therefore vacuum spray coating (-0.058\/-0.098 MPa) can be operated.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMoving Rack Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAutomatic movement in X and Y axis and the Z-direction is electrically adjustable. All three directions can be independently programmable. \u003c\/li\u003e\n\u003cli\u003eThe functions of solution feeding, ultrasonic spray, and bottom heating are integrated in touch screen for programmable setting.\u003c\/li\u003e\n\u003cli\u003eThe cross-sectional laser for tracking is available upon request. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eHeating Plate Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eThe standard heating plate is made of porous aluminum alloy and the maximum heating temperature is \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e300°C\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\u003cspan\u003eThe porous ceramic heating plate (150°C) with high surface flatness for flexible ultrathin substrate can be supplied upon request\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003eA higher temperature can be achieved by replaced with stainless steel plate for coating pyrolysis (up to 500\u003cspan\u003e°C\u003c\/span\u003e) \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eThe vacuum suction feature is used to firmly hold the substrate during the coating process. An oilless vacuum pump \u003ca href=\"https:\/\/echemsupplies.com\/products\/esovp?variant=47512544542950\"\u003eESOVP\u003c\/a\u003e is highly recommended. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cdiv style=\"text-align: start;\"\u003e           \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSRCUSC_06_100x100.png?v=1776623311\"\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL1000 * W700 * H900 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~200 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775314007782\"\u003eH. Su, et al., Low platinum loading for high temperature proton exchange membrane fuel cell developed by ultrasonic spray coating technique, Journal of Power Sources, 2014, 267, 155-159\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.3c04208\"\u003eW. Feng, et al., Mathematical Model-Assisted Ultrasonic Spray Coating for Scalable Production of Large-Sized Solid Oxide Electrochemical Cells, ACS Appl. Mater. Interfaces 2023, 15, 26, 31430–31437\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.rsc.org\/en\/content\/articlelanding\/2025\/ee\/d4ee03893b\"\u003eS. W. Lee, et al., Ultrasonic spraying of Ce(Mn,Fe)O2 nanocatalysts onto a perovskite surface for highly efficient electrochemical CO2 reduction, Energy Environ. Sci., 2025,18, 1205-1213\u003c\/a\u003e. \u003c\/p\u003e","brand":"FSN","offers":[{"title":"Default Title","offer_id":47553091633382,"sku":"EFLSPUSC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFLSPUSC_04.png?v=1776714049"},{"product_id":"efsebec","title":"ECS-FS Economic Benchtop Electrospinning Coater with Temperature \u0026 Humidity Monitoring, EFSEBEC","description":"\u003cp\u003eA Benchtop Electrospinning Coater with Temperature \u0026amp; Humidity Monitoring is a specialized fiber fabrication system used to produce non-woven membranes with fiber diameters ranging from several nanometers to micrometers.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eThe electrospinning process uses an intense electric field to draw a polymer or ceramic precursor solution into ultra-fine threads. (1) \u003cstrong\u003eHigh-Voltage Supply\u003c\/strong\u003e: A DC voltage (typically 10–30 kV) is applied between a metallic needle and a collector. (2) \u003cstrong\u003eTaylor Cone Formation\u003c\/strong\u003e: As the voltage increases, the hemispherical surface of the solution at the needle tip elongates into a conical shape. (3) \u003cstrong\u003eJetting \u0026amp; Whipping\u003c\/strong\u003e: Once the electrostatic force overcomes the surface tension, a liquid jet erupts. As it flies toward the collector, the solvent evaporates and the jet undergoes \"bending instability\" (whipping), thinning the fiber significantly. (4) \u003cstrong\u003eCollection\u003c\/strong\u003e: The solid fibers are deposited on a grounded collector (stationary plate or rotating drum) as a fibrous mat.\u003c\/p\u003e\n\u003cp\u003eElectrospinning is notoriously sensitive to environmental conditions. Integrated Temperature (T) and Humidity (H) monitors are critical for reproducibility: (1) \u003cstrong\u003eHumidity Control\u003c\/strong\u003e: High humidity can cause \"beading\" on the fibers or prevent the solvent from evaporating correctly, leading to fused fibers. For ceramic precursors used in SOFCs, moisture can trigger premature hydrolysis of the metal-organic precursors. (2) \u003cstrong\u003eTemperature Control\u003c\/strong\u003e: Temperature affects the viscosity of your precursor solution. As we discussed with your interest in automated viscosity testing, even a small change in temperature during the spinning process can alter the fiber diameter by hundreds of nanometers.\u003c\/p\u003e\n\u003cp\u003eThe working mechanism of an electrospinning process is shown below:\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_02_160x160.png?v=1776729495\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eEFSEBEC (EFS-EBEC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 1000 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eHigh Voltage Power Supply\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDC 0-30 kV, output current ≤1mA\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_03_100x100.png?v=1776730572\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCNC Operating System\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eThe 4.3-inch touch screen communicates with the PLC control\u003cbr\u003esystem.\u003c\/li\u003e\n\u003cli\u003eControl function: integrated control (operation of\u003cbr\u003enozzle moving device, liquid supply system, heating, exhaust,\u003cbr\u003etiming, lighting, etc.) and monitoring of the status of each\u003cbr\u003efunction.\u003c\/li\u003e\n\u003cli\u003eX-axis displacement spinning stroke: 50 ~ 200mm.\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eY-axis automatic motion module: effective stroke 150mm,\u003cbr\u003epositioning accuracy ±0.05mm, maximum speed 30mm\/s.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e         \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_04_100x100.png?v=1776732493\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003e\u003cem\u003eSolution Feeding System\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eLiquid supply mode: one motor pushes three (three-channel syringe pump).\u003c\/li\u003e\n\u003cli\u003eMaximum solution volume: 20mL.\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eAutomatic liquid supply speed range: 0.01 ~ 200mL\/h.\u003c\/li\u003e\n\u003cli\u003eManual liquid supply speed range: 0.1 ~ 50mL\/min.\u003c\/li\u003e\n\u003cli\u003eApplicable syringe specifications: 1, 3, 5, 10, 20mL.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e       \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_05_100x100.png?v=1776731883\"\u003e     \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_06_100x100.png?v=1776731883\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eStandard needles (Electrospinning Needles; 1-to-4 Needle, and Microsphere Needle) are included in the package:\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e      \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_09_100x100.png?v=1776736804\" alt=\"\" style=\"float: none;\"\u003e         \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_10_100x100.png?v=1776736805\" alt=\"\" style=\"float: none;\"\u003e      \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_11_100x100.png?v=1776736804\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMore needle types (eg: Two-layer coaxial nozzle, Four-needle dual-channel spinneret) can be supplied upon request.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e       \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_12_100x100.png?v=1776739846\" alt=\"\" style=\"float: none;\"\u003e       \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_15_160x160.png?v=1776739765\" alt=\"\" style=\"float: none;\"\u003e    \u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eNanofiber Receiving System\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eRoller Collector: effective width 150mm, ø80mm; speed: 100 ~3000r\/min.\u003c\/li\u003e\n\u003cli\u003eFlat Collection Plate: L-shaped 180mm*220mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_07_100x100.png?v=1776732372\" alt=\"\" style=\"float: none;\"\u003e   \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_08_100x100.png?v=1776732371\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eEnvironment Control\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature adjustment range of heating system: RT ~ 40 ℃. The heating temperature determines the humidity level inside chamber.  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eThe exhaust air volume of the exhaust fan: 0.5m³\/min.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eSafety Protection\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDischarge short circuit protection, running indicator light,\u003cbr\u003eautomatic alarm for unsafe operation.\u003c\/li\u003e\n\u003cli\u003eOrganic exhaust emission: avoid electric shock, fire,\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL520 * W570 * H750 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~52 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320304262\"\u003eM. Cai, et al., Lithium ion battery separator with improved performance via side-by-side bicomponent electrospinning of PVDF-HFP\/PI followed by 3D thermal crosslinking, Journal of Power Sources, 2020, 461, 228123\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775308016145\"\u003eC. Yang, et al., Polyvinylidene fluoride membrane by novel electrospinning system for separator of Li-ion batteries, Journal of Power Sources, 2009, 189, 716-720\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/advanced.onlinelibrary.wiley.com\/doi\/abs\/10.1002\/aenm.202000845\"\u003eX. Li, et al., Electrospinning-Based Strategies for Battery Materials, Adv. Energy Mater., 2021, 11, 2000845\u003c\/a\u003e. \u003c\/p\u003e","brand":"FSWM","offers":[{"title":"Default Title","offer_id":47556264362214,"sku":"EFSEBEC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_main.png?v=1776729320"},{"product_id":"efmmbec","title":"ECS-FM Multifunctional Benchtop Electrospinning Coater with Temperature \u0026 Humidity Monitoring, EFMMBEC","description":"\u003cp\u003eA Benchtop Electrospinning Coater with Temperature \u0026amp; Humidity Monitoring is a specialized fiber fabrication system used to produce non-woven membranes with fiber diameters ranging from several nanometers to micrometers.\u003c\/p\u003e\n\u003cdiv style=\"text-align: start;\" data-path-to-node=\"5\"\u003e\n\u003cp\u003eThe electrospinning process uses an intense electric field to draw a polymer or ceramic precursor solution into ultra-fine threads. (1) \u003cstrong\u003eHigh-Voltage Supply\u003c\/strong\u003e: A DC voltage (typically 10–30 kV) is applied between a metallic needle and a collector. (2) \u003cstrong\u003eTaylor Cone Formation\u003c\/strong\u003e: As the voltage increases, the hemispherical surface of the solution at the needle tip elongates into a conical shape. (3) \u003cstrong\u003eJetting \u0026amp; Whipping\u003c\/strong\u003e: Once the electrostatic force overcomes the surface tension, a liquid jet erupts. As it flies toward the collector, the solvent evaporates and the jet undergoes \"bending instability\" (whipping), thinning the fiber significantly. (4) \u003cstrong\u003eCollection\u003c\/strong\u003e: The solid fibers are deposited on a grounded collector (stationary plate or rotating drum) as a fibrous mat.\u003c\/p\u003e\n\u003cp\u003eElectrospinning is notoriously sensitive to environmental conditions. Integrated Temperature (T) and Humidity (H) monitors are critical for reproducibility: (1) \u003cstrong\u003eHumidity Control\u003c\/strong\u003e: High humidity can cause \"beading\" on the fibers or prevent the solvent from evaporating correctly, leading to fused fibers. For ceramic precursors used in SOFCs, moisture can trigger premature hydrolysis of the metal-organic precursors. (2) \u003cstrong\u003eTemperature Control\u003c\/strong\u003e: Temperature affects the viscosity of your precursor solution. As we discussed with your interest in automated viscosity testing, even a small change in temperature during the spinning process can alter the fiber diameter by hundreds of nanometers.\u003c\/p\u003e\n\u003cp\u003eThe working mechanism of an electrospinning process is shown below:\u003c\/p\u003e\n\u003cp\u003e\u003cimg style=\"float: none;\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_02_160x160.png?v=1776729495\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eEFMMEC (EFM-MBEC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 2500 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eTouch-Screen HMI System\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eTouch screen control function: integrated control (nozzle movement device, liquid supply system, temperature and humidity system, exhaust gas function, timing function,\u003cbr\u003eUV lamp)\u003c\/li\u003e\n\u003cli\u003eControl parameter settings (manual speed settings, automatic movement speed settings, height adjustment settings, return to zero, custom track settings and related control buttons).\u003c\/li\u003e\n\u003cli\u003eReal-time parameter monitoring.\u003c\/li\u003e\n\u003cli\u003eParameter record and output.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eHigh Voltage Power Supply\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDC -30 - 30 kV (double-high-voltage system), output current ≤1mA\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_02_100x100.png?v=1776741701\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eX-Y-Z Three-Axis Motion System\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAdjustable at angle for conjugate spinning module.\u003c\/li\u003e\n\u003cli\u003eX-axis manual displacement spinning stroke range: 50 ~ 300mm.\u003c\/li\u003e\n\u003cli\u003eY-axis automatic motion platform: reciprocating stroke 350mm; positioning accuracy ≤0.03mm.\u003c\/li\u003e\n\u003cli\u003eZ-axis manual lifting: 0 ~ 100mm adjustable.\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e         \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_03_100x100.png?v=1776742415\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003e\u003cem\u003eSolution Feeding and Nozzles\u003c\/em\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eThere are two built-in syringe pumps, both of which are one-push three (three-channel) syringe pumps, which can be independently controlled.\u003c\/li\u003e\n\u003cli\u003eAutomatic liquid supply speed range: 0.01 ~ 600 mL\/h;\u003c\/li\u003e\n\u003cli\u003eManual liquid supply speed range: 0.1 ~ 100mL\/min.\u003c\/li\u003e\n\u003cli\u003eApplicable syringe specifications: 1, 3, 5, 10, 20mL.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_05_100x100.png?v=1776743022\"\u003e    \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_06_100x100.png?v=1776743021\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe following standard needles are included in the package:\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e      \u003cstrong\u003eElectrospinning\u003c\/strong\u003e        \u003cstrong\u003e1-to-4 Needle\u003c\/strong\u003e      \u003cstrong\u003eMicrosphere Needle\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e      \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_09_100x100.png?v=1776736804\"\u003e        \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_10_100x100.png?v=1776736805\"\u003e      \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_11_100x100.png?v=1776736804\"\u003e\u003c\/p\u003e\n\u003cp\u003e  \u003cstrong\u003eTwo-layer coaxial nozzle \u003c\/strong\u003e             \u003cstrong\u003eSide-by-side nozzle\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e      \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_12_100x100.png?v=1776739846\"\u003e                             \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_08_100x100.png?v=1776744954\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eFour-needle dual-channel spinneret \u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv style=\"text-align: start;\"\u003e\n\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFSEBEC_15_240x240.png?v=1776739765\" alt=\"\" style=\"float: none;\"\u003e   \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_14_100x100.png?v=1776747308\" alt=\"\" style=\"float: none;\"\u003e\n\u003c\/div\u003e\n\u003cp\u003e\u003cstrong\u003eEight-needle single-channel array spinneret\u003c\/strong\u003e\u003c\/p\u003e\n\u003cdiv style=\"text-align: start;\"\u003e\n\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_07_240x240.png?v=1776744161\" style=\"margin-bottom: 16px; float: none;\"\u003e  \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_15_100x100.png?v=1776747308\" style=\"margin-bottom: 16px; float: none;\"\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"text-align: start;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThere are more \u003cspan style=\"color: rgb(255, 42, 0);\"\u003eoptional\u003c\/span\u003e ones that can be supplied upon request.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e     \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_20_100x100.png?v=1776749983\"\u003e     \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_19_100x100.png?v=1776749983\"\u003e    \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_21_100x100.png?v=1776749983\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eNanofiber Receiving System\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eRoller collector: effective width 350mm, diameter ø160mm; roller speed: 100 ~ 2500r\/min adjustable. \u003c\/li\u003e\n\u003cli\u003eFlat collector: L-shaped 400*250mm, preparation of two nanofiber membranes at the same time to improve spinning efficiency.\u003c\/li\u003e\n\u003cli\u003eParallel electrode collector: adjustable spacing from 0 ~ 100mm, preparation of aligned fibers.   \u003c\/li\u003e\n\u003cli\u003eTube collector: One tube for each size: φ2 ~ φ8mm, preparation of tubular scaffold         \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e       \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_09_100x100.png?v=1776746159\" alt=\"\" style=\"float: none;\"\u003e     \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_10_100x100.png?v=1776746159\" alt=\"\" style=\"float: none;\"\u003e         \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_11_100x100.png?v=1776746159\"\u003e\u003c\/p\u003e\n\u003cp\u003e       \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_13_100x100.png?v=1776746159\"\u003e        \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_12_100x100.png?v=1776746159\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe disc collector is also available upon request.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_24_100x100.png?v=1776751736\"\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTo realize the continuous electrospinning production, a roll-to-roll unit (0.01 ~ 5m\/min, W=180 mm) can be integrated. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e         \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_25_100x100.png?v=1776751943\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eElectrospinning + Ultrasonic Spray (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional\u003c\/span\u003e)\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eThe ultrasonic spray coating can be integrated with the electrospinning for fabricating multifunctional composite. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_17_100x100.png?v=1776748263\" alt=\"\" style=\"float: none;\"\u003e    \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_18_100x100.png?v=1776748393\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eNano-Yarn Configuration (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional\u003c\/span\u003e)\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eThe electrospinning nano-yarn system (0.05-300r\/min) with a double nozzle system, rotating funnel, and yarn collector can be supplied upon request.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e         \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_22_100x100.png?v=1776750338\"\u003e     \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_23_100x100.png?v=1776750338\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eEnvironment Control\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eTemperature adjustment range of heating system: RT ~ 60 ℃ (±1℃).\u003c\/li\u003e\n\u003cli\u003eHumidity controllable: 35% ~ room humidity adjustable, accuracy ±3%RH, control time≤15min.\u003c\/li\u003e\n\u003cli\u003eThe exhaust air volume of the exhaust fan: 0.5m³\/min.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eSafety Protection\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDischarge short circuit protection.\u003c\/li\u003e\n\u003cli\u003eRunning indicator light.\u003c\/li\u003e\n\u003cli\u003eSafety signs, automatic alarm for unsafe operation.\u003c\/li\u003e\n\u003cli\u003eLeakage protection.\u003c\/li\u003e\n\u003cli\u003eOrganic waste gas emission: avoid electric shock, fire, explosion, and other accidents caused by charge accumulation, and avoid leakage of organic waste gas so as not to affect health.\u003c\/li\u003e\n\u003cli\u003eBe able to access inert gas and its control functions.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL1210 * W800 * H1040 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~150 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320304262\"\u003eM. Cai, et al., Lithium ion battery separator with improved performance via side-by-side bicomponent electrospinning of PVDF-HFP\/PI followed by 3D thermal crosslinking, Journal of Power Sources, 2020, 461, 228123\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775308016145\"\u003eC. Yang, et al., Polyvinylidene fluoride membrane by novel electrospinning system for separator of Li-ion batteries, Journal of Power Sources, 2009, 189, 716-720\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/advanced.onlinelibrary.wiley.com\/doi\/abs\/10.1002\/aenm.202000845\"\u003eX. Li, et al., Electrospinning-Based Strategies for Battery Materials, Adv. Energy Mater., 2021, 11, 2000845\u003c\/a\u003e. \u003c\/p\u003e","brand":"FSWM","offers":[{"title":"Default Title","offer_id":47556915200230,"sku":"EFMMBEC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EFMMBEC_main.png?v=1776753083"},{"product_id":"ewmspc","title":"ECS-W Manual Screen Printing Coater, EWMSPC","description":"\u003cp\u003eA Manual Screen Printing Coater is the most basic yet essential tool for researchers transitioning from simple drop-casting or hand-painting to more controlled electrode fabrication. It is normally used to deposit consistent layers of high-viscosity slurries onto ceramic or metallic supports. Unlike automatic versions, a manual coater relies on the operator's hand to provide the squeegee pressure and speed, but it provides a fixed frame and alignment system that is far superior to free-hand methods.\u003c\/p\u003e\n\u003cp\u003eA laboratory-grade manual screen printer typically includes: (1) \u003cstrong\u003eBase with Vacuum Chuck\u003c\/strong\u003e: A flat surface (often aluminum or ceramic) with micro-holes connected to a vacuum pump. This is critical for holding your Ni-YSZ anode supports or thin foils perfectly flat during the stroke. (2) \u003cstrong\u003eAdjustable Frame Holder\u003c\/strong\u003e: A set of clamps that hold the screen mesh. It allows for \"Off-Contact\" adjustment—the small gap between the mesh and the substrate that ensures the mesh \"snaps\" back, leaving a clean print. (3) \u003cstrong\u003eSqueegee \u0026amp; Flood Bar\u003c\/strong\u003e:  Squeegee: A rubber\/polyurethane blade used to push the slurry through the mesh. Flood Bar: Used to spread a thin layer of slurry across the mesh before the actual printing stroke. (4) \u003cstrong\u003eX-Y-Theta Fine Tuning\u003c\/strong\u003e: Micrometer knobs that allow you to move the substrate table with sub-millimeter precision for multi-layer alignment (e.g., aligning a GDC buffer layer exactly over a YSZ electrolyte).\u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEWMSPC (EW-MSPC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eAluminum Plate Size\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e240*300 mm for small size\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003e310*405 mm for medium size\u003c\/li\u003e\n\u003cli\u003e440*590 mm for large size\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eMax. Frame Thickness\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e40 mm thick for all sizes\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eMax. Up\/Down Height\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e140 mm for all sizes \u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eCoater Dimension\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL300 * W240 * H140 mm for small size\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/echemsupplies.com\/products\/essawrw100?variant=47492793827558\"\u003e\u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCIHCVB_03_160x160.png?v=1774808616\"\u003e\u003c\/a\u003eL405 * W310 * H140 mm for medium size\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/echemsupplies.com\/products\/essawrw100?variant=47492793827558\"\u003e\u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCIHCVB_03_160x160.png?v=1774808616\"\u003e\u003c\/a\u003eL449 * W310 * H140 mm for large size\u003ca href=\"https:\/\/echemsupplies.com\/products\/essawrw100?variant=47492793827558\"\u003e\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0013468607008171\"\u003eA. Gören, et al., Mechanical and electrical properties of a LiCoO2 cathode prepared by screen-printing for a lithium-ion micro-battery, Electrochimica Acta, 2007, 52, 7895-7902\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/acfdd1\/meta\"\u003eF. Shen, et al., Tape Casting of Thin Electrolyte and Thick Cathode for Halide-Based All-Solid-State Batteries, J. Electrochem. Soc., 2023, 170, 100505\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/advanced.onlinelibrary.wiley.com\/doi\/abs\/10.1002\/admi.201600450\"\u003eM. S. Kim, et al., Multifunctional Separator Coatings for High-Performance \u003c\/a\u003e\u003cbr\u003e\u003ca href=\"https:\/\/advanced.onlinelibrary.wiley.com\/doi\/abs\/10.1002\/admi.201600450\"\u003eLithium–Sulfur Batteries, Adv. Mater. Interfaces, 2016, 3, 1600450\u003c\/a\u003e. \u003c\/p\u003e","brand":"WWYS","offers":[{"title":"Small Size (240*300 mm)","offer_id":47557409669350,"sku":"EWMSPCS","price":299.0,"currency_code":"USD","in_stock":true},{"title":"Medium Size (405*310)","offer_id":47557409734886,"sku":"EWMSPCM","price":399.0,"currency_code":"USD","in_stock":true},{"title":"Large Size (590*440)","offer_id":47557409767654,"sku":"EWMSPCL","price":499.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EWMSPC_main.png?v=1776761375"},{"product_id":"ewhpmspc","title":"ECS-W High Precision Manual Screen Printing Coater, EWHPMSPC","description":"\u003cp\u003eA Manual Screen Printing Coater is the most basic yet essential tool for researchers transitioning from simple drop-casting or hand-painting to more controlled electrode fabrication. It is normally used to deposit consistent layers of high-viscosity slurries onto ceramic or metallic supports. Unlike automatic versions, a manual coater relies on the operator's hand to provide the squeegee pressure and speed, but it provides a fixed frame and alignment system that is far superior to free-hand methods.\u003c\/p\u003e\n\u003cp\u003eA laboratory-grade manual screen printer typically includes: (1) \u003cstrong\u003eBase with Vacuum Chuck\u003c\/strong\u003e: A flat surface (often aluminum or ceramic) with micro-holes connected to a vacuum pump. This is critical for holding your Ni-YSZ anode supports or thin foils perfectly flat during the stroke. (2) \u003cstrong\u003eAdjustable Frame Holder\u003c\/strong\u003e: A set of clamps that hold the screen mesh. It allows for \"Off-Contact\" adjustment—the small gap between the mesh and the substrate that ensures the mesh \"snaps\" back, leaving a clean print. (3) \u003cstrong\u003eSqueegee \u0026amp; Flood Bar\u003c\/strong\u003e:  Squeegee: A rubber\/polyurethane blade used to push the slurry through the mesh. Flood Bar: Used to spread a thin layer of slurry across the mesh before the actual printing stroke. (4) \u003cstrong\u003eX-Y-Theta Fine Tuning\u003c\/strong\u003e: Micrometer knobs that allow you to move the substrate table with sub-millimeter precision for multi-layer alignment (e.g., aligning a GDC buffer layer exactly over a YSZ electrolyte).\u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEWHPMSPC (EW-MSPC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eAluminum Plate Size\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e200*200 mm for small size\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003e300*400 mm for medium size\u003c\/li\u003e\n\u003cli\u003e400*500 mm for large size\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eMax. Frame Thickness\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e50 mm thick for all sizes\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eMax. Up\/Down Height\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e130 mm for small size\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e230 mm for medium size\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e360 mm for large size\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePosition Adjustment\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003eHigh precision position adjustment (1 mm in 30 mm range in left\/right and front\/back)\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eRotation Angle\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003eThe aluminum plate can be rotated in 10 degrees. \u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eAccessories\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003eA scraper and ink blade are included.\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan style=\"font-size: 0.875rem;\"\u003e         \u003c\/span\u003e\u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EWHPMSPC_03_100x100.png?v=1776787205\"\u003e    \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EWHPMSPC_04_100x100.png?v=1776787370\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eCoater Dimension\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL300 * W400 * H330 mm for small size\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/echemsupplies.com\/products\/essawrw100?variant=47492793827558\"\u003e\u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCIHCVB_03_160x160.png?v=1774808616\"\u003e\u003c\/a\u003eL320 * W500 * H430 mm for medium size\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/echemsupplies.com\/products\/essawrw100?variant=47492793827558\"\u003e\u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSTCCIHCVB_03_160x160.png?v=1774808616\"\u003e\u003c\/a\u003eL400 * W600 * H580 mm for large size\u003ca href=\"https:\/\/echemsupplies.com\/products\/essawrw100?variant=47492793827558\"\u003e\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0013468607008171\"\u003eM. S. Park, et al., Mechanical and electrical properties of a LiCoO2 cathode prepared by screen-printing for a lithium-ion micro-battery, Electrochimica Acta, 2007, 52, 7895-7902\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S037877531631401X\"\u003eA. Gören, et al., High performance screen-printed electrodes prepared by a green solvent approach for lithium-ion batteries, Journal of Power Sources, 2016, 334, 65-77\u003c\/a\u003e\u003c\/p\u003e","brand":"WWYS","offers":[{"title":"Small Size (300*400 mm)","offer_id":47558177816806,"sku":"EWHPMSPCS","price":499.0,"currency_code":"USD","in_stock":true},{"title":"Medium Size (320*500 mm)","offer_id":47558177849574,"sku":"EWHPMSPCM","price":699.0,"currency_code":"USD","in_stock":true},{"title":"Large Size (400*600 mm)","offer_id":47558177882342,"sku":"EWHPMSPCL","price":899.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EWHPMSPC_main.png?v=1776784347"},{"product_id":"ewsasasp","title":"ECS-W Semi-Automatic Swing-Arm Screen Printing Coater (Max. 150*200 mm), EWSASASP","description":"\u003cp\u003eAn Automatic (or Semi-Automatic) Swing-Arm Screen Printing Coater is a classic workhorse in electrochemical labs and pilot lines. It bridges the gap between manual prototyping and full-scale production, offering the precision required for SOFC\/SOEC planar cells and advanced battery electrodes (like SPAN cathodes). The \"swing-arm\" refers to the printing head or frame holder that pivots upward at an angle. This design is preferred for R\u0026amp;D because it provides easy access to the substrate and the screen for cleaning and alignment between runs.\u003c\/p\u003e\n\u003cp\u003eThe key features of the semi-automatic swing-arm screen printer are shown below: (1) \u003cstrong\u003eSwing-Arm Movement\u003c\/strong\u003e: The screen frame rotates upward (typically 45° to 60°). This is a massive ergonomics advantage when you need to frequently wipe the screen to prevent high-viscosity YSZ\/GDC slurries from drying in the mesh. (2) \u003cstrong\u003eMotorized Squeegee \u0026amp; Flood Bar\u003c\/strong\u003e: Unlike manual units, the printing stroke is driven by a precision motor (often a frequency-controlled or servo motor). This ensures that the speed and pressure are identical for every single cell, which is the only way to achieve repeatable layer thickness. (3) \u003cstrong\u003eAutomatic Flood Cycle\u003c\/strong\u003e: The machine automatically \"floods\" the screen with slurry after each print. This keeps the mesh wet, preventing the solvent (like Terpineol) from evaporating and clogging the screen.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eEWSASASP (EW-SASASP)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, single phase, 50\/60 Hz, 300W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eCritical Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAluminum Plate Size: 120mm * 200mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eMaximum Frame Size: 300mm * 400mm\u003c\/li\u003e\n\u003cli style=\"color: rgb(255, 42, 0);\"\u003e\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eScreen Printing Area: Max. 150mm * 200mm (larger sizes can be supplied upon request)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli style=\"color: rgb(0, 0, 0);\"\u003e\u003cspan style=\"color: rgb(0, 0, 0);\"\u003eCoating speed is controlled by the pneumatic gas pressure, which can be adjusted by rotating the speed knobs at sides. \u003c\/span\u003e\u003c\/li\u003e\n\u003cli style=\"color: rgb(0, 0, 0);\"\u003e\u003cspan style=\"color: rgb(0, 0, 0);\"\u003eThe control panel has functions of motion directions, printing times, start\/pause, speed and counter time display, and emergency stop button. \u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan style=\"color: rgb(0, 0, 0);\"\u003e          \u003c\/span\u003e\u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EWSASASP_03_100x100.png?v=1776791429\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eGas Compressor\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA gas compressor (\u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e) is required to provide pneumatic force (5-7 bar, around 70-100 psi) for operation\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EUQOFGC_main_100x100.png?v=1775414665\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eDimension\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL600 * W280 * H740 mm\u003ca href=\"https:\/\/echemsupplies.com\/products\/essawrw100?variant=47492793827558\"\u003e\u003c\/a\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\n\u003cp\u003eWeight\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~45 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0013468607008171\"\u003eM. S. Park, et al., Mechanical and electrical properties of a LiCoO2 cathode prepared by screen-printing for a lithium-ion micro-battery, Electrochimica Acta, 2007, 52, 7895-7902\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S037877531631401X\"\u003eA. Gören, et al., High performance screen-printed electrodes prepared by a green solvent approach for lithium-ion batteries, Journal of Power Sources, 2016, 334, 65-77\u003c\/a\u003e\u003c\/p\u003e","brand":"WWYS","offers":[{"title":"Default Title","offer_id":47558280544486,"sku":"EWSASASP","price":2499.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EWSASASP_main.png?v=1776789092"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/collections\/ESSMR2RC_main.png?v=1776819918","url":"https:\/\/echemsupplies.com\/collections\/coaters.oembed","provider":"EChem Supplies","version":"1.0","type":"link"}