{"title":"Coin Cells Equipment","description":"\u003cp\u003e\u003cstrong\u003eCoin cell assembly is where electrochemical claims are made or broken — burr-free electrode discs, a wetted but not flooded stack, and a uniformly crimped gas-tight seal are the prerequisites for any cycling data you intend to publish.\u003c\/strong\u003e This collection covers the bench-scale hardware used to build CR20XX-series cells (CR2016, CR2025, CR2032) and larger formats such as CR2450 and CR3032, organized along the three workflow steps that actually drive coin-cell quality: cutting the electrodes, dosing the electrolyte, and crimping the case.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eDisc cutting\u003c\/strong\u003e determines whether you have clean, repeatable electrode geometry or microscopic burrs that pierce the separator and short the cell. Manual disc punches use a spring-loaded plunger and hardened steel die set (typical sizes 12, 15, 16, 18, 19, 20 mm); they are the right tool for low-throughput work and for thick or brittle coatings where operator feel matters. Pneumatic disc cutters drive the die with compressed gas to deliver consistent, high-velocity shear across hundreds of discs per session, and most pneumatic units are sized to operate inside an argon glovebox.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eElectrolyte filling\u003c\/strong\u003e needs a pipette compatible with corrosive, volatile, moisture-sensitive liquids and with the viscosity range you are running, from carbonate-based formulations through ionic liquids. Both digital electronic pipettes and stepwise mechanical pipettes are stocked in glovebox-friendly configurations, with overlapping volume ranges from sub-microliter to one milliliter so single-cell dosing and small pouch top-ups can share a workflow.\u003c\/p\u003e\n\n\u003cp\u003e\u003cstrong\u003eCrimping\u003c\/strong\u003e is the step that locks the gasket geometry and therefore the long-term seal. Three crimper architectures are offered:\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManual hydraulic crimpers\u003c\/strong\u003e — the laboratory workhorse, hand-pumped, with universal CR20XX dies and optional dies for CR2450 and CR3032.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePneumatic crimpers\u003c\/strong\u003e — gas-driven, fast, and free of hydraulic-oil contamination; preferred for in-glovebox assembly under Ar or N2.\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eElectric crimpers with controllable pressure\u003c\/strong\u003e — touch-screen or dial-set sealing force in tons or psi, for series in which every cell must see an identical crimp profile (sulfur cathodes, MXenes, lithium-metal anodes).\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eIf you are setting up a new coin-cell line, start with a manual hydraulic crimper and a manual disc punch; for higher throughput or sensitive chemistries, move to pneumatic or electric crimping and a pneumatic cutter. For the consumable hardware that goes into the cells, see coin cell cases \u0026amp; gaskets; for full assembly lines, see \u003ca href=\"\/collections\/battery-equipment\"\u003ebattery equipment\u003c\/a\u003e.\u003c\/p\u003e\n","products":[{"product_id":"esscceccp","title":"ECS-SS Electric Crimper with Controllable Pressure for Coin Cells- ESSCCECCP","description":"\u003cp\u003eAn electric coin cell crimper is a significant upgrade over manual hydraulic versions. It provides the consistent sealing pressure required to minimize contact resistance and prevent electrolyte leakage, which is especially critical when testing sensitive materials like MXenes or sulfur-based cathodes.\u003c\/p\u003e\n\u003cp\u003eElectric crimpers offer several technical benefits: (1) \u003cstrong\u003ePrecision Control\u003c\/strong\u003e: You can set the exact sealing pressure (typically in metric tons or psi). This ensures every cell in a test series is identical. (2) \u003cstrong\u003eGas-Tight Integrity\u003c\/strong\u003e: Consistent pressure ensures the gasket is deformed perfectly every time, which is vital for long-term cycling or high-temperature tests. (3) \u003cstrong\u003eErgonomics\u003c\/strong\u003e: In high-throughput labs, manual pumping leads to fatigue and inconsistent sealing toward the end of a batch. (4) \u003cstrong\u003eGlovebox Compatibility\u003c\/strong\u003e: Most electric models are designed with a compact footprint and remote control boxes to fit inside argon-filled gloveboxes without taking up excessive space.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSCCECCP (ESS-CC-ECCP)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, 50\/60Hz, 360 W \u003c\/li\u003e\n\u003cli\u003e\n\u003cspan style=\"font-size: 0.875rem;\"\u003eThe electrical motor is compatible with Ar gas environment in glovebox\u003c\/span\u003e\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eCrimping Dies\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eCell size range: φ5.0-φ35mm; Height: Max.10mm\u003c\/li\u003e\n\u003cli\u003eOne set of crimping die\u003ca href=\"http:\/\/www.mtixtl.com\/MSK-110DieSetReplacement-MSK-110-DS.aspx\"\u003e\u003c\/a\u003e for CR2032, CR2025, and CR2016 is included\u003c\/li\u003e\n\u003cli\u003eOptional die available from product option for crimping CR2325, CR2450, AG3, AG5. \u003c\/li\u003e\n\u003cli\u003eThe de-crimping dies, such as CR16, CR20, CR24, or CR30 is available upon request\u003c\/li\u003e\n\u003cli\u003eCoin cell crimping sequence:\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0638\/4664\/6008\/files\/MSK-110-A-Positive_Assembling_Sequence_160x160.jpg?v=1737414414\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePressure\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAdjustable pressure in touch screen.\u003c\/li\u003e\n\u003cli\u003eMax. 1000 kgf (recommend value is 500-700 kgf)\u003c\/li\u003e\n\u003cli\u003ePressure sensor resolution: ±0.5％ F.S\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 39.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 39.2px;\"\u003e\n\u003cp\u003eCrimping Efficiency\u003c\/p\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\u003cbr\u003e\u003c\/div\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 39.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~2.5 pcs\/min (only for reference)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eTraverse Distance during Crimping\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e15 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL300*W220*H470mm (antechamber compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~32 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMaintenance\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003eTo maintain the precision of an electric crimper:\u003c\/p\u003e\n\u003cp\u003e(1) \u003cstrong\u003eDie Cleaning\u003c\/strong\u003e: Electrolyte salts (especially LiPF6) are corrosive. If a cell leaks during crimping, the die must be cleaned immediately with ethanol or DI water to prevent pitting.\u003c\/p\u003e\n\u003cp\u003e(2) \u003cstrong\u003eCalibration\u003c\/strong\u003e: Periodically check the pressure sensor against a calibrated load cell to ensure the \"set\" pressure matches the \"actual\" force applied.\u003c\/p\u003e\n\u003cp\u003e(3) \u003cstrong\u003eGasket Alignment\u003c\/strong\u003e: Ensure the coin cell \"cup\" is centered in the die. Off-center crimping is the #1 cause of short circuits in newly assembled cells.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/app.jove.com\/t\/4104\/construction-and-testing-of-coin-cells-of-lithium-ion-batteries\"\u003eA. Kayyar, et al., Construction and Testing of Coin Cells of Lithium Ion Batteries, JOVE, DOI: 10.3791\/4104\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/11106.1629ecst\/meta\"\u003eK. S. Jiang, et al., How reliable is coin-cell-based ranking of Li anode Coulombic efficiency?, Joule, 2025, 9, 101963\u003c\/a\u003e. \u003c\/li\u003e\n\u003c\/ol\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47488636584166,"sku":"ESSCCECCP","price":2999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCECCP_main_02.png?v=1776020016"},{"product_id":"essccmdec","title":"ECS-SS Precise Manual Disk Electrode Cutter for Coin Cells, ESSCCMDEC","description":"\u003cp\u003eFor precise electrode disc preparation, the choice between a manual punch and an automated cutter depends on your throughput and the physical properties of your coated \"tapes.\" For coin cell assembly (CR2016, CR2025, CR2032), the edges must be perfectly burr-free to prevent internal short circuits.\u003c\/p\u003e\n\u003cp\u003eFor the manual disk electrode cutter, which uses a spring-loaded plunger and a hardened steel die to \"punch\" the disc out of the foil. The standard diameters are normally 12, 15, 16, 18, 19, and 20 mm dies. Typically, the cathode is cut to 14–15 mm and the anode to 15–16 mm to ensure complete coverage and account for slight misalignment during assembly. Compact to pneumatic or electric one, it can be transferred to the glovebox antechamber and no power is required for operation. \u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 482.4px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSCCMDEC (ESS-CC-MDEC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003ePunching Force\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e200 kg force\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 67.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 67.2px;\"\u003e\u003cem\u003ePunching Materials\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 67.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.01-0.5 mm thickness Electrodes, Current Collectors, and Separators\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003eTraverse Distance\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 16 mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 51.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 51.2px;\"\u003e\n\u003cp\u003e\u003cem\u003eCutting Dies\u003c\/em\u003e\u003c\/p\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\u003ca href=\"https:\/\/echemsupplies.com\/products\/esacd?variant=47734190801126\"\u003e\u003cimg height=\"77\" width=\"77\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESACD_main_100x100.jpg?v=1780381699\" alt=\"\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/a\u003e\u003c\/div\u003e\n\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 51.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eφ3～φ24, regular sizes of φ8,  φ10, φ12, φ14, φ15, φ16, φ19, and φ20 can be supplied quickly, while other sizes also can be provided with slightly long lead time. \u003c\/li\u003e\n\u003cli\u003eStandard cutting dies of \u003cspan style=\"color: rgb(255, 42, 0);\"\u003eφ14 and φ16\u003c\/span\u003e are included in the package. \u003c\/li\u003e\n\u003cli\u003ePlease select needed cutting die sizes when purchase the disk cutter\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 126px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 126px;\"\u003e\u003cem\u003eNote\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 126px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eBefore the installation of die sets, please check the part number (eg. A30612) of pushing rod and bottom plate is consistent.\u003c\/li\u003e\n\u003cli\u003eThe alignment for pushing rod and bottom plate is critical. Normally the bottom plate should be loose until the pushing rod constantly goes through the hole smoothly. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL140 * W200 * H400 mm (antechamber and glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~16 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.cell.com\/joule\/fulltext\/S2542-4351(19)30053-4\"\u003eS. Chen, et al., Critical Parameters for Evaluating Coin Cells and Pouch Cells of Rechargeable Li-Metal Batteries, Joule, 2019, 3, 1094-1105\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1.3515072\/meta\"\u003eT. Marks, et al., A Guide to Li-Ion Coin-Cell Electrode Making for Academic Researchers, J. Electrochem. Soc., 2011, 158, A51\u003c\/a\u003e.\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47495388725478,"sku":"ESSCCMDEC","price":1999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMDEC_main.png?v=1774899958"},{"product_id":"esscchtpdec","title":"ECS-SS High-Throughput Pneumatic Disk Electrode Cutter (D=15, 16, 19 mm) for Coin Cells, ESSCCHTPDEC","description":"\u003cp\u003eFor high-throughput coin cell electrode preparation, pneumatic disc cutters are the industry standard due to their speed, repeatability, and ability to handle delicate or brittle materials without the mechanical \"stutter\" of manual punches.\u003c\/p\u003e\n\u003cp\u003eThe high-throughput pneumatic disk cutter has the following features: (1) \u003cstrong\u003eBurr-Free Edges\u003c\/strong\u003e: Pneumatic systems provide a consistent, high-velocity vertical force that shears the foil cleanly. This is vital to prevent microscopic metal \"burrs\" that could pierce the separator and cause cell failure during cycling. (2) \u003cstrong\u003eGlovebox Safety\u003c\/strong\u003e: Most high-throughput models are purely pneumatic. Because they use no electricity, they eliminate the risk of sparks and heat generation inside the volatile atmosphere of a glovebox. (3) \u003cstrong\u003eLow Material Waste\u003c\/strong\u003e: High-throughput dies are often arranged in optimized patterns to maximize the number of discs per square centimeter of your coated tape.\u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSCCHTPDEC (ESS-CC-HTPDEC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePunching Force\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 1 T (for electrode cutting, 500 kg force is recommended)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePunching Materials\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.01-0.5 mm thickness Electrodes, Current Collectors, and Separators\u003c\/li\u003e\n\u003cli\u003eVertical Bur: ≤12μm, Horizontal Bur: ≤20μm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eTraverse Distance\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 12 mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCutting Dies\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eStandard φ15, φ16, and φ19 cutting dies are included.\u003c\/li\u003e\n\u003cli\u003eOther Sizes, φ8,  φ10, φ12, φ14, and φ20 can be supplied upon request\u003c\/li\u003e\n\u003cli\u003e1-to-8 pieces are produced. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCHTPDEC_02_100x100.png?v=1774907225\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eGas Compressor\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA gas compressor or a gas tank is required to provide 60-80 psi to support the pneumatic operation. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eNote\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe cutting die plate should be tightly fixed on the cutter by rotating the top knob. \u003c\/li\u003e\n\u003cli\u003eThe acrylic plate should be placed at the bottom to avoid cutting blade damage\u003c\/li\u003e\n\u003cli\u003eThe electrode debris should be cleaned in time. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL370 * W245 * H245 mm (antechamber and glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~38 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.cell.com\/joule\/fulltext\/S2542-4351(19)30053-4\"\u003eS. Chen, et al., Critical Parameters for Evaluating Coin Cells and Pouch Cells of Rechargeable Li-Metal Batteries, Joule, 2019, 3, 1094-1105\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1.3515072\/meta\"\u003eT. Marks, et al., A Guide to Li-Ion Coin-Cell Electrode Making for Academic Researchers, J. Electrochem. Soc., 2011, 158, A51\u003c\/a\u003e.\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47496377696486,"sku":"ESSCCHTPDEC","price":2999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCHTPDEC_main.png?v=1774907072"},{"product_id":"essccmhc","title":"ECS-SS Manual Hydraulic Crimper (CR20XX) for Coin Cells, ESSCCMHC","description":"\u003cp\u003eFor manual coin cell assembly, a hydraulic manual crimper is the standard \"workhorse\" for laboratory research. It uses a hand-pumped hydraulic jack to provide the high, uniform pressure needed to deform the coin cell gasket and create a gas-tight seal.\u003c\/p\u003e\n\u003cp\u003eThe critical specifications for the manual hydraulic crimper are: (1) \u003cstrong\u003eDie Compatibility\u003c\/strong\u003e: Most units come with a universal die for CR2016, CR2025, and CR2032. Optional dies are required for larger cells like CR2450 or CR3032. (2) \u003cstrong\u003eSealing Pressure\u003c\/strong\u003e: For CR20XX series cells, the recommended sealing pressure is typically 800–1000 psi (approximately 50–70 kg\/cm2). (3) \u003cstrong\u003ePTFE Anti-Corrosion Core\u003c\/strong\u003e: High-quality crimpers use a PTFE core to prevent the coin cell from short-circuiting against the steel die during the crimping process. (4) \u003cstrong\u003eWeight\u003c\/strong\u003e: If you plan to move the unit in and out of a glovebox frequently, look for \"Compact\" or \"Lite\" versions which weigh 12–25 kg, compared to standard versions which can reach 40 kg.\u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSCCMHC (ESS-CC-MHC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoin Cell Size\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eDiameter: φ5.0-φ35mm, \u003c\/li\u003e\n\u003cli\u003eMax. Height: 10mm\u003c\/li\u003e\n\u003cli\u003eA standard crimping die set for CR20XX is included.\u003c\/li\u003e\n\u003cli\u003eOther sizes in the φ13mm~φ35mm can be customized. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCrimping Pressure\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. Pressure: 8 T\u003c\/li\u003e\n\u003cli\u003eFor CR20XX coin cell series, the recommended pressure is 800-1000 psi.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e        \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_03_100x100.png?v=1774978063\" alt=\"\" style=\"float: none;\"\u003e         \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_04_100x100.png?v=1774978063\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eTraverse Distance\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e20 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDe-crimping Die (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional\u003c\/span\u003e)\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe De-crimping can be found here, which will be used to disassemble the coin cell for post-analysis. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_05_100x100.png?v=1774978301\"\u003e         \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_02_100x100.png?v=1774977964\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eOperation Environment\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe crimper should be placed inside a glovebox or a dryroom for operation due to electrolyte sensitivity. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL230 * W180 * H330 mm (glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~27 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/ad2731\/meta\"\u003eC. Soulen, et al., Bridging the Gap Between Pouch and Coin Cell Electrochemical Performance in Lithium Metal Batteries, J. Electrochem. Soc., 2024, 171, 020535\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.mdpi.com\/1996-1073\/15\/21\/7949\"\u003eP. M .Luc, et al., Reproducible Production of Lithium-Ion Coin Cells, Energies, 2022, 15, 7949\u003c\/a\u003e.\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47496751907046,"sku":"ESSCCMHC","price":1799.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_main.png?v=1774916678"},{"product_id":"essccpc","title":"ECS-SS Pneumatic Crimper (CR20XX) for Coin Cells, ESSCCPC","description":"\u003cp\u003eFor coin cell assembly inside a glovebox, a pneumatic crimper is often considered the optimal balance between the speed of an electric unit and the reliability of a manual hydraulic one. Since it uses compressed gas (Ar or N2) to drive the sealing die, it eliminates the risk of hydraulic oil leaks and the potential for electrical arcing in an Argon atmosphere.\u003c\/p\u003e\n\u003cp\u003eThe advantages compared to other types of crimpers are summarized below: (1) \u003cstrong\u003evs. Manual Hydraulic\u003c\/strong\u003e: No risk of oil leaking into your sensitive Argon environment. It is also significantly faster and less fatiguing for high-throughput batches. (2) vs. \u003cstrong\u003eElectric\u003c\/strong\u003e: Generally more robust and less susceptible to the \"arcing\" issues that some 24V DC motors face in high-purity Argon. (3) \u003cstrong\u003evs. Pneumatic-Hydraulic Hybrid\u003c\/strong\u003e: Pure pneumatic systems are lighter (typically 25–30 kg) and easier to pass through the glovebox antechamber.\u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESSCCPC (ESS-CC-PC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoin Cell Size\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eDiameter: φ5.0-φ35mm, \u003c\/li\u003e\n\u003cli\u003eMax. Height: 10mm\u003c\/li\u003e\n\u003cli\u003eA standard crimping die set for CR20XX is included.\u003c\/li\u003e\n\u003cli\u003eOther sizes in the φ13mm~φ35mm can be customized. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e        \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_03_100x100.png?v=1774978063\" alt=\"\" style=\"float: none;\"\u003e         \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_04_100x100.png?v=1774978063\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCrimping Pressure\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. Pressure: 1 MPa (manually adjust the input pressure)\u003c\/li\u003e\n\u003cli\u003eFor CR20XX coin cell series, the recommended pressure is 800-1000 psi.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eTraverse Distance\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e20 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eGlovebox Operation\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe KF40 feedthrough is included for gas ventilation\u003c\/li\u003e\n\u003cli\u003eGas consumption amount\/each time is 490 mL\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDe-crimping Die (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional\u003c\/span\u003e)\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe De-crimping can be found here, which will be used to disassemble the coin cell for post-analysis. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_05_100x100.png?v=1774978301\"\u003e         \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_02_100x100.png?v=1774977964\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL370 * W245 * H350 mm (glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~30 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/ad2731\/meta\"\u003eC. Soulen, et al., Bridging the Gap Between Pouch and Coin Cell Electrochemical Performance in Lithium Metal Batteries, J. Electrochem. Soc., 2024, 171, 020535\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.mdpi.com\/1996-1073\/15\/21\/7949\"\u003eP. M .Luc, et al., Reproducible Production of Lithium-Ion Coin Cells, Energies, 2022, 15, 7949\u003c\/a\u003e.\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47499629363430,"sku":"ESSCCPC","price":1999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCPC_main.png?v=1774979601"},{"product_id":"ersccmdec","title":"ECS-RS Economic Manual Disk Electrode Cutter for Coin Cells, ERSCCMDEC","description":"\u003cp\u003eFor precise electrode disc preparation, the choice between a manual punch and an automated cutter depends on your throughput and the physical properties of your coated \"tapes.\" For coin cell assembly (CR2016, CR2025, CR2032), the edges must be perfectly burr-free to prevent internal short circuits.\u003c\/p\u003e\n\u003cp\u003eFor the manual disk electrode cutter, which uses a spring-loaded plunger and a hardened steel die to \"punch\" the disc out of the foil. The standard diameters are normally 12, 15, 16, 18, 19, and 20 mm dies. Typically, the cathode is cut to 14–15 mm and the anode to 15–16 mm to ensure complete coverage and account for slight misalignment during assembly. Compact to pneumatic or electric one, it can be transferred to the glovebox antechamber and no power is required for operation. \u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eERSCCMDEC (ERS-CC-MDEC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePunching Materials\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.005-0.5 mm thickness Electrodes, Current Collectors, and Separators\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eTraverse Distance\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. 25 mm\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCutting Dies\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eStandard cutting dies of \u003cspan style=\"color: rgb(255, 42, 0);\"\u003eφ15 and φ19\u003c\/span\u003e are included in the package\u003c\/li\u003e\n\u003cli\u003eφ8～φ24, regular sizes of φ8,  φ10, φ12, φ14, φ15, φ16, φ19, and φ20 can be supplied quickly, while other sizes also can be provided with slightly long lead time. \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003ePlease select needed cutting die sizes when purchase the disk cutter\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eNote\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe alignment for pushing rod and bottom plate is critical. Normally the bottom plate should be loose until the pushing rod constantly goes through the hole smoothly. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL110 * W150 * H235 mm (antechamber and glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~6 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.cell.com\/joule\/fulltext\/S2542-4351(19)30053-4\"\u003eS. Chen, et al., Critical Parameters for Evaluating Coin Cells and Pouch Cells of Rechargeable Li-Metal Batteries, Joule, 2019, 3, 1094-1105\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1.3515072\/meta\"\u003eT. Marks, et al., A Guide to Li-Ion Coin-Cell Electrode Making for Academic Researchers, J. Electrochem. Soc., 2011, 158, A51\u003c\/a\u003e.\u003c\/p\u003e","brand":"RSC","offers":[{"title":"Default Title","offer_id":47503534588134,"sku":"ERSCCMDEC","price":1199.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSCCMDEC_main.png?v=1775089118"},{"product_id":"ersefmp","title":"ECS-RS Mechanical Pipette for Electrolyte Filling, ERSEFMP","description":"\u003cp\u003eFor precise electrolyte filling in battery research, the choice of pipetting tool depends on the viscosity of your electrolyte (e.g., standard LiPF6 in carbonates vs. thick ionic liquids) and whether you are working inside an argon-filled glovebox. Because electrolytes are often corrosive, volatile, and sensitive to moisture, standard laboratory pipettes require specific configurations to maintain accuracy and tool longevity.\u003c\/p\u003e\n\u003ctable style=\"width: 49.5\u0026lt;p\u0026gt;For precise electrolyte filling in battery research, the choice of pipetting tool depends on the viscosity of your electrolyte (e.g., standard LiPF6 in carbonates vs. thick ionic liquids) and whether you are working inside an argon-filled glovebox. Because electrolytes are often corrosive, volatile, and sensitive to moisture, standard laboratory pipettes require specific configurations to maintain accuracy and tool longevity.\u0026lt;\/p\u0026gt;\u0026lt;table style=;\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 117.637px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 675.363px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eERSEFMP (ERS-EF-MP)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 117.637px;\"\u003e\u003cem\u003ePipette Volume\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 675.363px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.1 uL to 10 mL\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 117.637px;\"\u003e\u003cem\u003ePipette Types\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 675.363px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.1-2.5 uL\u003c\/li\u003e\n\u003cli\u003e0.5-10 uL\u003c\/li\u003e\n\u003cli\u003e2-20 uL\u003c\/li\u003e\n\u003cli\u003e5-50 uL\u003c\/li\u003e\n\u003cli\u003e10-100 uL\u003c\/li\u003e\n\u003cli\u003e20-200 uL\u003c\/li\u003e\n\u003cli\u003e50-200 uL\u003c\/li\u003e\n\u003cli\u003e100-1000 uL\u003c\/li\u003e\n\u003cli\u003e200-1000 uL\u003c\/li\u003e\n\u003cli\u003e1000-5000 uL\u003c\/li\u003e\n\u003cli\u003e2-10 mL\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePipette Parameters\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cdiv\u003e\u003cimg alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSEFMP_02_480x480.png?v=1775091183\"\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/2.0121910jes\/meta\"\u003eF. J. Günter, et al., Influence of the Electrolyte Quantity on Lithium-Ion Cells, J. Electrochem. Soc., 2019, 166, A1709\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/2.1171902jes\/meta\"\u003eV. Murray, et al., A Guide to Full Coin Cell Making for Academic Researchers, J. Electrochem. Soc., 2019, 166, A329\u003c\/a\u003e.\u003c\/p\u003e","brand":"RSC","offers":[{"title":"0.1-2.5 uL","offer_id":47503622635750,"sku":"ERSEFMP01","price":99.0,"currency_code":"USD","in_stock":true},{"title":"0.5-10 uL","offer_id":47503622668518,"sku":"ERSEFMP02","price":99.0,"currency_code":"USD","in_stock":true},{"title":"2-20 uL","offer_id":47503622701286,"sku":"ERSEFMP03","price":99.0,"currency_code":"USD","in_stock":true},{"title":"5-50 uL","offer_id":47503622734054,"sku":"ERSEFMP04","price":99.0,"currency_code":"USD","in_stock":true},{"title":"10-100 uL","offer_id":47503622766822,"sku":"ERSEFMP05","price":99.0,"currency_code":"USD","in_stock":true},{"title":"20-200 uL","offer_id":47503622799590,"sku":"ERSEFMP06","price":99.0,"currency_code":"USD","in_stock":true},{"title":"50-200 uL","offer_id":47503622832358,"sku":"ERSEFMP07","price":99.0,"currency_code":"USD","in_stock":true},{"title":"100-1000 uL","offer_id":47503622865126,"sku":"ERSEFMP08","price":99.0,"currency_code":"USD","in_stock":true},{"title":"200-1000 uL","offer_id":47503622897894,"sku":"ERSEFMP09","price":99.0,"currency_code":"USD","in_stock":true},{"title":"1000-5000 uL","offer_id":47503622930662,"sku":"ERSEFMP10","price":99.0,"currency_code":"USD","in_stock":true},{"title":"2-10 mL","offer_id":47503622963430,"sku":"ERSEFMP11","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSEFMP_main.png?v=1775090574"},{"product_id":"esefepds","title":"ECS-S Electronic Pipette with Digital Screen for Electrolyte Filling, ESEFEPDS","description":"\u003cp\u003eFor precise electrolyte filling in battery research, the choice of pipetting tool depends on the viscosity of your electrolyte (e.g., standard LiPF6 in carbonates vs. thick ionic liquids) and whether you are working inside an argon-filled glovebox. Because electrolytes are often corrosive, volatile, and sensitive to moisture, standard laboratory pipettes require specific configurations to maintain accuracy and tool longevity.\u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eESEFEPDS (ES-EF-EPDS)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower \u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMagnetic charging (USB cable)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e        \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESEFEPDS_03_100x100.png?v=1775103895\" alt=\"\" style=\"float: none;\"\u003e  \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESEFEPDS_04_160x160.png?v=1775104103\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePipette Volume\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.5 uL to 1 mL\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePipette Types\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.5-10 uL\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003e10-200 uL\u003c\/li\u003e\n\u003cli\u003e30-300 uL\u003c\/li\u003e\n\u003cli\u003e50-1000 uL\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eOperation Mode\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eSample Transfer Mode (P-H)\u003c\/li\u003e\n\u003cli\u003eSample Homogenize Mode (P-Y)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDigital Screen \u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: start;\"\u003e        \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESEFEPDS_02_100x100.png?v=1775103821\" alt=\"\" style=\"margin-bottom: 16px; float: none;\"\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePipette Parameters\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cdiv style=\"text-align: start;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESEFEPDS_05_480x480.png?v=1775104856\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/div\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/2.0121910jes\/meta\"\u003eF. J. Günter, et al., Influence of the Electrolyte Quantity on Lithium-Ion Cells, J. Electrochem. Soc., 2019, 166, A1709\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/2.1171902jes\/meta\"\u003eV. Murray, et al., A Guide to Full Coin Cell Making for Academic Researchers, J. Electrochem. Soc., 2019, 166, A329\u003c\/a\u003e.\u003c\/p\u003e","brand":"MKSYS","offers":[{"title":"0.1-2.5 uL","offer_id":47505527275750,"sku":"ESEFEPDS01","price":199.0,"currency_code":"USD","in_stock":true},{"title":"10-200 uL","offer_id":47505527308518,"sku":"ESEFEPDS02","price":199.0,"currency_code":"USD","in_stock":true},{"title":"30-300 uL","offer_id":47505527341286,"sku":"ESEFEPDS03","price":199.0,"currency_code":"USD","in_stock":true},{"title":"50-1000 uL","offer_id":47505527374054,"sku":"ESEFEPDS04","price":199.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESEFEPDS_main.png?v=1775103629"},{"product_id":"ersccmhc","title":"ECS-RS Economic Manual Hydraulic Crimper (CR20XX) for Coin Cells, ERSCCMHC","description":"\u003cp\u003eFor manual coin cell assembly, a hydraulic manual crimper is the standard \"workhorse\" for laboratory research. It uses a hand-pumped hydraulic jack to provide the high, uniform pressure needed to deform the coin cell gasket and create a gas-tight seal.\u003c\/p\u003e\n\u003cp\u003eThe critical specifications for the manual hydraulic crimper are: (1) \u003cstrong\u003eDie Compatibility\u003c\/strong\u003e: Most units come with a universal die for CR2016, CR2025, and CR2032. Optional dies are required for larger cells like CR2450 or CR3032. (2) \u003cstrong\u003eSealing Pressure\u003c\/strong\u003e: For CR20XX series cells, the recommended sealing pressure is typically 800–1000 psi (approximately 50–70 kg\/cm2). (3) \u003cstrong\u003ePTFE Anti-Corrosion Core\u003c\/strong\u003e: High-quality crimpers use a PTFE core to prevent the coin cell from short-circuiting against the steel die during the crimping process. (4) \u003cstrong\u003eWeight\u003c\/strong\u003e: If you plan to move the unit in and out of a glovebox frequently, look for \"Compact\" or \"Lite\" versions which weigh 12–25 kg, compared to standard versions which can reach 40 kg.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eERSCCMHC (ERS-CC-MHC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoin Cell Size\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA standard crimping die set for CR20XX is included.\u003c\/li\u003e\n\u003cli\u003eOptional die available from product option for crimping CR2325, CR2450, AG3, AG5\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCrimping Pressure\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. Pressure: 200 kg\/cm2\u003c\/li\u003e\n\u003cli\u003eFor CR20XX coin cell series, the recommended pressure is 80-100 kg\/cm2. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eTraverse Distance\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e20 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDe-crimping Die (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional\u003c\/span\u003e)\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe De-crimping can be found here, which will be used to disassemble the coin cell for post-analysis. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_05_100x100.png?v=1774978301\" alt=\"\" style=\"float: none;\"\u003e         \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_02_100x100.png?v=1774977964\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eOperation Environment\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe crimper should be placed inside a glovebox or a dryroom for operation due to electrolyte sensitivity. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL230 * W170 * H330 mm (glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~28 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/ad2731\/meta\"\u003eC. Soulen, et al., Bridging the Gap Between Pouch and Coin Cell Electrochemical Performance in Lithium Metal Batteries, J. Electrochem. Soc., 2024, 171, 020535\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.mdpi.com\/1996-1073\/15\/21\/7949\"\u003eP. M .Luc, et al., Reproducible Production of Lithium-Ion Coin Cells, Energies, 2022, 15, 7949\u003c\/a\u003e.\u003c\/p\u003e","brand":"RSC","offers":[{"title":"Default Title","offer_id":47505613160678,"sku":"ERSCCMHC","price":1699.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSCCMHC_main.png?v=1775107615"},{"product_id":"ersccpc","title":"ECS-RS Pneumatic Crimper (CR20XX) for Coin Cells, ERSCCPC","description":"\u003cp\u003eFor coin cell assembly inside a glovebox, a pneumatic crimper is often considered the optimal balance between the speed of an electric unit and the reliability of a manual hydraulic one. Since it uses compressed gas (Ar or N2) to drive the sealing die, it eliminates the risk of hydraulic oil leaks and the potential for electrical arcing in an Argon atmosphere.\u003c\/p\u003e\n\u003cp\u003eThe advantages compared to other types of crimpers are summarized below: (1) \u003cstrong\u003evs. Manual Hydraulic\u003c\/strong\u003e: No risk of oil leaking into your sensitive Argon environment. It is also significantly faster and less fatiguing for high-throughput batches. (2) vs. \u003cstrong\u003eElectric\u003c\/strong\u003e: Generally more robust and less susceptible to the \"arcing\" issues that some 24V DC motors face in high-purity Argon. (3) \u003cstrong\u003evs. Pneumatic-Hydraulic Hybrid\u003c\/strong\u003e: Pure pneumatic systems are lighter (typically 25–30 kg) and easier to pass through the glovebox antechamber.\u003c\/p\u003e\n\u003ctable style=\"height: 201.2px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eERSCCPC (ERS-CC-PC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCoin Cell Size\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eA standard crimping die set for CR20XX is included.\u003c\/li\u003e\n\u003cli\u003eOptional die available from product option for crimping CR2325, CR2450, AG3, AG5\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eCrimping Pressure\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eMax. Pressure: 1 MPa (manually adjust the input gas pressure)\u003c\/li\u003e\n\u003cli\u003eFor CR20XX coin cell series, the recommended pressure is 0.7 MPa\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eTraverse Distance\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003e30 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eGlovebox Operation\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe KF40 feedthrough is included for gas ventilation\u003c\/li\u003e\n\u003cli\u003eGas consumption amount\/each time is 490 mL\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ETSCCPC_03_160x160.png?v=1775114870\" style=\"margin-bottom: 16px; float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDe-crimping Die (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional\u003c\/span\u003e)\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe De-crimping can be found here, which will be used to disassemble the coin cell for post-analysis. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_05_100x100.png?v=1774978301\"\u003e         \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_02_100x100.png?v=1774977964\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL290 * W205 * H330 mm (glovebox-compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~25 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1945-7111\/ad2731\/meta\"\u003eC. Soulen, et al., Bridging the Gap Between Pouch and Coin Cell Electrochemical Performance in Lithium Metal Batteries, J. Electrochem. Soc., 2024, 171, 020535\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.mdpi.com\/1996-1073\/15\/21\/7949\"\u003eP. M .Luc, et al., Reproducible Production of Lithium-Ion Coin Cells, Energies, 2022, 15, 7949\u003c\/a\u003e.\u003c\/p\u003e","brand":"RSC","offers":[{"title":"Default Title","offer_id":47505646813414,"sku":"ERSCCPC","price":1999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ERSCCPC_main.png?v=1782151339"},{"product_id":"erscceccp","title":"ECS-RS Electric Crimper with Controllable Pressure in Touch-Screen for Coin Cells- ERSCCECCP","description":"\u003cp\u003eAn electric coin cell crimper is a significant upgrade over manual hydraulic versions. It provides the consistent sealing pressure required to minimize contact resistance and prevent electrolyte leakage, which is especially critical when testing sensitive materials like MXenes or sulfur-based cathodes.\u003c\/p\u003e\n\u003cp\u003eElectric crimpers offer several technical benefits: (1) \u003cstrong\u003ePrecision Control\u003c\/strong\u003e: You can set the exact sealing pressure (typically in metric tons or psi). This ensures every cell in a test series is identical. (2) \u003cstrong\u003eGas-Tight Integrity\u003c\/strong\u003e: Consistent pressure ensures the gasket is deformed perfectly every time, which is vital for long-term cycling or high-temperature tests. (3) \u003cstrong\u003eErgonomics\u003c\/strong\u003e: In high-throughput labs, manual pumping leads to fatigue and inconsistent sealing toward the end of a batch. (4) \u003cstrong\u003eGlovebox Compatibility\u003c\/strong\u003e: Most electric models are designed with a compact footprint and remote control boxes to fit inside argon-filled gloveboxes without taking up excessive space.\u003c\/p\u003e\n\u003ctable width=\"100%\" style=\"height: 201.2px;\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eETSCCECCP (ETS-CC-ECCP)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, 50\/60Hz, 100 W \u003c\/li\u003e\n\u003cli\u003e\n\u003cspan style=\"font-size: 0.875rem;\"\u003eThe electrical motor is compatible with Ar gas environment in glovebox\u003c\/span\u003e\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 35.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 35.6px;\"\u003e\u003cem\u003eCrimping Dies\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 35.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eOne set of crimping die\u003ca href=\"http:\/\/www.mtixtl.com\/MSK-110DieSetReplacement-MSK-110-DS.aspx\"\u003e\u003c\/a\u003e for CR2032, CR2025, and CR2016 is included\u003c\/li\u003e\n\u003cli\u003eOptional die available from product option for crimping CR2325, CR2450, AG3, AG5. \u003c\/li\u003e\n\u003cli\u003eThe de-crimping dies, such as CR16, CR20, CR24, or CR30 is available upon request\u003c\/li\u003e\n\u003cli\u003eCoin cell crimping sequence:\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e           \u003cimg style=\"margin-bottom: 16px; float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0638\/4664\/6008\/files\/MSK-110-A-Positive_Assembling_Sequence_160x160.jpg?v=1737414414\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003ePressure\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cul\u003e\n\u003cli\u003eAdjustable pressure in touch screen.\u003c\/li\u003e\n\u003cli\u003eMax. 1200 kgf (recommend value is 700-800 kgf)\u003c\/li\u003e\n\u003cli\u003ePressure sensor resolution: ±0.5％ F.S\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eTraverse Distance during Crimping\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e20 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003cem\u003eDe-crimping Die (\u003cspan style=\"color: rgb(255, 42, 0);\"\u003eOptional\u003c\/span\u003e)\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe De-crimping can be found here, which will be used to disassemble the coin cell for post-analysis. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e               \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_05_100x100.png?v=1774978301\"\u003e         \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSCCMHC_02_100x100.png?v=1774977964\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eDimension\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eL250*W185*H450mm (antechamber and glovebox compatible)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd style=\"width: 17.9856%;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~30 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eMaintenance\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003eTo maintain the precision of an electric crimper:\u003c\/p\u003e\n\u003cp\u003e(1) \u003cstrong\u003eDie Cleaning\u003c\/strong\u003e: Electrolyte salts (especially LiPF6) are corrosive. If a cell leaks during crimping, the die must be cleaned immediately with ethanol or DI water to prevent pitting.\u003c\/p\u003e\n\u003cp\u003e(2) \u003cstrong\u003eCalibration\u003c\/strong\u003e: Periodically check the pressure sensor against a calibrated load cell to ensure the \"set\" pressure matches the \"actual\" force applied.\u003c\/p\u003e\n\u003cp\u003e(3) \u003cstrong\u003eGasket Alignment\u003c\/strong\u003e: Ensure the coin cell \"cup\" is centered in the die. Off-center crimping is the #1 cause of short circuits in newly assembled cells.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/app.jove.com\/t\/4104\/construction-and-testing-of-coin-cells-of-lithium-ion-batteries\"\u003eA. Kayyar, et al., Construction and Testing of Coin Cells of Lithium Ion Batteries, JOVE, DOI: 10.3791\/4104\u003c\/a\u003e.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/11106.1629ecst\/meta\"\u003eK. S. Jiang, et al., How reliable is coin-cell-based ranking of Li anode Coulombic efficiency?, Joule, 2025, 9, 101963\u003c\/a\u003e. \u003c\/li\u003e\n\u003c\/ol\u003e","brand":"RSC","offers":[{"title":"Default Title","offer_id":47506020532454,"sku":"ERSCCECCP","price":3499.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ERSCCECCP_main.png?v=1782151573"},{"product_id":"ersccehhdec","title":"ECS-RS Economic Hand-Held Disk Electrode Cutter (φ10-20 mm) for Coin Cells, ERSCCEHHDEC","description":"\u003cp\u003eA hand-held disk electrode cutter (often referred to as a compact or manual disc punch) is a staple tool in coin cell (CR2016, CR2025, CR2032) prototyping. It allows researchers to quickly punch precise, burr-free circular disks from current collector foils coated with cathode or anode materials.\u003c\/p\u003e\n\u003cp\u003eThe standard sizes depend on the specific component of the coin cell being fabricated: (1) \u003cstrong\u003eCathode Disks\u003c\/strong\u003e: Typically φ12 mm or φ13 mm (to ensure it fits cleanly inside the coin cell cup without shorting the edges). (2) \u003cstrong\u003eAnode Disks\u003c\/strong\u003e: Typically φ14 mm to φ15 mm (slightly larger than the cathode to prevent lithium dendrite growth and alignment-induced short circuits around the edges). (3) \u003cstrong\u003eSeparator Disks\u003c\/strong\u003e: Typically φ16 mm, φ18 mm, or φ19 mm (must completely overlap both electrodes to isolate them).\u003c\/p\u003e\n\u003ctable style=\"height: 477.413px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eERSCCEHHDEC (ERS-CC-EHHDEC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 67.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 67.2px;\"\u003e\u003cem\u003ePunching Materials\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 67.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.005-0.5 mm thickness Electrodes, Current Collectors, and Separators\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 253.413px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 253.413px;\"\u003e\u003cem\u003eCutting Dies\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 253.413px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eStandard cutting rings of \u003cspan style=\"color: rgb(255, 42, 0);\"\u003eφ10, φ12, φ15, φ16, φ19, and φ19\u003c\/span\u003e are included in the package\u003c\/li\u003e\n\u003cli\u003eAny other size in the range of φ9～φ20 are also available upon request.\u003c\/li\u003e\n\u003cli\u003eThe cutting dies with rectangular shapes also can be supplied upon request.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ERSCCEHHDEC_03_100x100.png?v=1782156071\" alt=\"\" style=\"float: none;\"\u003e  \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ERSCCEHHDEC_04_100x100.png?v=1782156071\" alt=\"\" style=\"float: none;\" width=\"93\" height=\"87\"\u003e     \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ERSCCEHHDEC_05_100x100.png?v=1782156071\" alt=\"\" style=\"float: none;\" width=\"132\" height=\"83\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 61.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 61.6px;\"\u003e\u003cem\u003eNote\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 61.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe cutting dies should be placed at the center of the magnetic base.  \u003c\/li\u003e\n\u003cli\u003eThe sharp blade side should face the cutting material. \u003c\/li\u003e\n\u003cli\u003eIf the cutting dies become blunt after long-term use, replace it with a new one.\u003c\/li\u003e\n\u003cli\u003eThe cushion base is a consumable\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~0.9 lb\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.cell.com\/joule\/fulltext\/S2542-4351(19)30053-4\"\u003eS. Chen, et al., Critical Parameters for Evaluating Coin Cells and Pouch Cells of Rechargeable Li-Metal Batteries, Joule, 2019, 3, 1094-1105\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1.3515072\/meta\"\u003eT. Marks, et al., A Guide to Li-Ion Coin-Cell Electrode Making for Academic Researchers, J. Electrochem. Soc., 2011, 158, A51\u003c\/a\u003e.\u003c\/p\u003e","brand":"TSSG","offers":[{"title":"Default Title","offer_id":47909208883430,"sku":"ERSCCEHHDEC","price":149.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ERSCCEHHDEC_main.png?v=1782156071"},{"product_id":"erscpchdhhec","title":"ECS-RS Heavy-Duty Hand-Held Electrode Cutter (φ8-50 mm \u0026 25*25-50*50mm) for Coin and Pouch Cell, ERSCPCHDHHEC","description":"\u003cp\u003eExpanding a hand-held cutter's capability to pouch cells introduces specific mechanical challenges: (1) \u003cstrong\u003eIncreased Cutting Force \u0026amp; Edge Distortion\u003c\/strong\u003e: A circular punch distributing force over a φ15 mm diameter has a total cutting perimeter of roughly 47 mm. A modest pouch cell electrode (50*50 mm) has a cutting perimeter of 200 mm. Standard plier-style hand grips cannot generate enough uniform pressure for pouch dimensions. However, the risk is the insufficient, uneven manual force results in severe foil stretching, wrinkling, and coating delamination along the long straight edges of the pouch electrode. A mechanical lever arm or hydraulic assist is mandatory for pouch cell sizes. (2) \u003cstrong\u003eAlignment and Coating Tolerances\u003c\/strong\u003e: Coin cells are self-centering within the punch slot. Pouch cell electrodes require exact alignment to ensure the coating boundary aligns perfectly with the bare metal tab. Manual cutters for pouch cells must include adjustable magnetic or physical registration guides to ensure repeatability.\u003c\/p\u003e\n\u003ctable style=\"height: 328.6px;\" width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003eERSCPCHDHHEC (ERS-CPC-HDHHEC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 67.2px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 67.2px;\"\u003e\u003cem\u003ePunching Materials\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 67.2px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e0.05-1.0 mm thickness Electrodes, Current Collectors, and Separators\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 145.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 145.6px;\"\u003e\u003cem\u003eCutting Dies\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 145.6px;\"\u003e\n\u003cul\u003e\n\u003cli\u003e(1) Disk Electrodes (Coin Cells): \u003cspan style=\"color: rgb(255, 42, 0);\"\u003eφ8-φ50 mm. \u003cspan style=\"color: rgb(0, 0, 0);\"\u003eThe cutting size for each hand-held die cutter is fixed value and cannot be exchanged or upgraded.  \u003c\/span\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e(2) Rectangular Electrodes (Punch Cells): \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e25*25 mm, 40*40 mm, and 50*50 mm\u003c\/span\u003e (other customized sizes can be supplied upon request.\u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 20.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 20.6px;\"\u003e\u003cem\u003eNote\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 20.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003eThe cutting samples should cover the cutting blade frame \u003c\/li\u003e\n\u003cli\u003eThe cutting debris should be cleaned in time\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr style=\"height: 47.6px;\"\u003e\n\u003ctd style=\"width: 17.9856%; height: 47.6px;\"\u003e\u003ci\u003eWeight\u003c\/i\u003e\u003c\/td\u003e\n\u003ctd style=\"width: 81.6547%; height: 47.6px;\"\u003e\n\u003cdiv style=\"text-align: left;\"\u003e\n\u003cul\u003e\n\u003cli\u003e~4 lb\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.cell.com\/joule\/fulltext\/S2542-4351(19)30053-4\"\u003eS. Chen, et al., Critical Parameters for Evaluating Coin Cells and Pouch Cells of Rechargeable Li-Metal Batteries, Joule, 2019, 3, 1094-1105\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1149\/1.3515072\/meta\"\u003eT. Marks, et al., A Guide to Li-Ion Coin-Cell Electrode Making for Academic Researchers, J. Electrochem. Soc., 2011, 158, A51\u003c\/a\u003e.\u003c\/p\u003e","brand":"SHYNS","offers":[{"title":"Disk Electrode: φ8","offer_id":47909389533414,"sku":"ERSCPCHDHHECD8","price":169.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ10","offer_id":47909389566182,"sku":"ERSCPCHDHHECD10","price":189.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ11","offer_id":47909491605734,"sku":"ERSCPCHDHHECD11","price":189.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ12","offer_id":47909491638502,"sku":"ERSCPCHDHHECD12","price":189.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ13","offer_id":47909491671270,"sku":"ERSCPCHDHHECD13","price":189.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ14","offer_id":47909491704038,"sku":"ERSCPCHDHHECD14","price":189.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ15","offer_id":47909491736806,"sku":"ERSCPCHDHHECD15","price":189.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ16","offer_id":47909491769574,"sku":"ERSCPCHDHHECD16","price":189.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ18","offer_id":47909491802342,"sku":"ERSCPCHDHHECD18","price":199.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ19","offer_id":47909491835110,"sku":"ERSCPCHDHHECD19","price":199.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ20","offer_id":47909491867878,"sku":"ERSCPCHDHHECD20","price":199.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ25","offer_id":47909491900646,"sku":"ERSCPCHDHHECD25","price":219.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ30","offer_id":47909491933414,"sku":"ERSCPCHDHHECD30","price":229.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ35","offer_id":47909491966182,"sku":"ERSCPCHDHHECD35","price":239.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ40","offer_id":47909491998950,"sku":"ERSCPCHDHHECD40","price":239.0,"currency_code":"USD","in_stock":true},{"title":"Disk Electrode: φ50","offer_id":47909496815846,"sku":"ERSCPCHDHHECD50","price":249.0,"currency_code":"USD","in_stock":true},{"title":"Rectangular Electrode: 25*25 mm","offer_id":47909496848614,"sku":"ERSCPCHDHHECR2525","price":199.0,"currency_code":"USD","in_stock":true},{"title":"Rectangular Electrode: 40*40 mm","offer_id":47909496881382,"sku":"ERSCPCHDHHECR4040","price":219.0,"currency_code":"USD","in_stock":true},{"title":"Rectangular Electrode: 50*50 mm","offer_id":47909496914150,"sku":"ERSCPCHDHHECR5050","price":249.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ERSCPCHDHHEC_main.png?v=1782159965"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/collections\/ESSCCECCP_main_02.png?v=1776020055","url":"https:\/\/echemsupplies.com\/collections\/coin-cells-equipment.oembed","provider":"EChem Supplies","version":"1.0","type":"link"}