{"title":"Dip Coaters","description":"\u003cp\u003e\u003cstrong\u003eDip coating turns a beaker of precursor and a controlled withdrawal speed into a uniform thin film — but only when the lift mechanism, environment, and sample geometry are matched to your chemistry.\u003c\/strong\u003e The dip coaters in this collection cover the full span from sub-nm\/s monolayer assembly to roll-to-roll separator functionalization, so you can pick the unit that fits your substrate size, viscosity range, and downstream thermal step.\u003c\/p\u003e\n\n\u003cp\u003eDip coating is a workhorse in sol-gel synthesis, layer-by-layer (LbL) assembly, separator and membrane functionalization, and protective overcoats for SOFC, battery, and electrolyzer components. Film thickness is governed by withdrawal speed, solution viscosity, and evaporation rate (Landau-Levich and capillary regimes), so reproducibility depends almost entirely on motion control and atmosphere stability.\u003c\/p\u003e\n\n\u003ch3\u003eSpeed and resolution\u003c\/h3\u003e\n\u003cp\u003eFor ultra-thin coatings — self-assembled monolayers, ordered ceramic membranes, sub-100 nm sol-gel layers — choose nano-speed or micro-speed units that drive the substrate at nm\/s to um\/s through piezo or high-resolution stepper stages. These run in the capillary \/ evaporation regime where film thickness is decoupled from inertial fluid dynamics. For routine sol-gel and slurry work, standard programmable coaters in the mm\/s range are sufficient.\u003c\/p\u003e\n\n\u003ch3\u003eThroughput and multi-layer workflows\u003c\/h3\u003e\n\u003cp\u003eMulti-position carousel coaters (4, 5, or 6 stations) are built for LbL assembly, alternating-layer stacks, and rinse cycles between active, binder, and wash baths. Independent heating and stirring per station keep precursor solutions stable across long runs. Angle-adjustable variants let you tilt the substrate from 0° to 90° to break the vertical wedge effect and tune meniscus behavior on each face.\u003c\/p\u003e\n\n\u003ch3\u003eSubstrate size and integrated thermal processing\u003c\/h3\u003e\n\u003cp\u003eMedium and large programmable coaters extend stroke and motor torque for planar SOFC supports, electrode foils, and membranes up to a few hundred millimeters per side. Units with an integrated drying oven or three-zone tube furnace let you dip, withdraw, and pass the green film straight into a calcination or sintering profile without manual transfer. For continuous webs — separator functionalization, ion-exchange membrane fabrication, double-sided coatings — a roll-to-roll dip coater with metering rod and IR drying replaces the discrete batch.\u003c\/p\u003e\n\n\u003cp\u003eIf you are building monolayers or sub-100 nm films, start with the nano- and micro-speed units; for LbL or sol-gel multilayer work, use the multi-position carousel coaters; for continuous separator or membrane processing, see the roll-to-roll variant. Related sections: \u003ca href=\"\/collections\/coaters\"\u003eCoaters\u003c\/a\u003e and Laboratory Equipment.\u003c\/p\u003e\n","products":[{"product_id":"esmr2rdc","title":"ECS-SM Roll-to-Roll Dip Coater (Max. 280 mm) with Metering Wire Rod and IR Heating, ESMR2RDC","description":"\u003cp\u003eA Roll-to-Roll (R2R) Dip Coater is a classic \"immersion\" coating system where the substrate (web) is passed through a liquid bath to be coated on both sides simultaneously. While Slot-Die and Doctor Blade coating are preferred for primary electrodes, dip coating is a vital process in your research for functionalizing separators and fabricating ion-exchange membranes where full saturation or double-sided application is required.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\"\u003e\n\u003cp\u003eIn a R2R dip coater, the foil or membrane is guided into a reservoir (dip tank) by a series of rollers. (1)\u003cstrong\u003e Immersion\u003c\/strong\u003e: The web travels down into the coating fluid. (2) \u003cstrong\u003ePick-up\u003c\/strong\u003e: As it emerges vertically, a liquid film adheres to both sides of the substrate. (3) \u003cstrong\u003eMetering (The Landau-Levich Regime)\u003c\/strong\u003e: The final thickness is determined primarily by the withdrawal speed and the viscosity of the fluid. (4) \u003cstrong\u003eDoctoring (Optional)\u003c\/strong\u003e: Many R2R dip coaters include \"Air Knives\" or \"Squeeze Rollers\" at the exit of the tank to blow off or press out excess liquid to achieve a specific target thickness.\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMR2RDC_02.png?v=1775712442\" alt=\"\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESMR2RDC (ESM-R2RDC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 3000 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eGeneral Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eRoller width: 300 mm \u003c\/li\u003e\n\u003cli\u003eLoading substrate width: Max. 280 mm\u003c\/li\u003e\n\u003cli\u003eCoating width: Max. 280 mm\u003c\/li\u003e\n\u003cli\u003eMechanical coating speed: 0.05-0.75m\/min (the real coating speed depends on the slurry properties and dry oven length\/temperature)\u003c\/li\u003e\n\u003cli\u003eThe general design drawing is shown below:\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMR2RDC_03_160x160.png?v=1775717717\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eUnwinding\/Winding Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eRoller diameter: 3\", mechanical expansion for tightening the loading roll substrate and collection cardboard. \u003c\/li\u003e\n\u003cli\u003eMax. winding\/unwinding roll diameter: 300 mm \u003c\/li\u003e\n\u003cli\u003eAlignment Sensors were installed and aligning position resolution could be ±0.3-0.5 mm. \u003cbr\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDip Coating Parts\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eSlurry Container Size: 0.3 L (0.7 L and 2.7 L can be supplied upon request)\u003c\/li\u003e\n\u003cli\u003eSlurry Viscosity: 50-500 cP (Recommended).\u003c\/li\u003e\n\u003cli\u003eThe peristaltic pump \u003ca href=\"https:\/\/echemsupplies.com\/products\/eabsfpp2l?variant=47522046673126\"\u003eEABSFPP2L\u003c\/a\u003e can be supplied as slurry feeder for the dip coating. \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg style=\"float: none;\" alt=\"\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EABSFPP2L_main_100x100.png?v=1775628781\"\u003e         \u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMetering Wire Rod\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAfter dip coating, the wet coating film will go through the metering wire rods and obtain desirable thickness. \u003c\/li\u003e\n\u003cli\u003eThe standard wire rod (\u003ca href=\"https:\/\/echemsupplies.com\/products\/esmawrw300?variant=47525192040678\"\u003eESMAWRW300\u003c\/a\u003e) is D10 mm, effective coating length is 300 mm, and groove \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e            \u003ca href=\"https:\/\/echemsupplies.com\/products\/esmawrw300?variant=47525192040678\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMAWRW300_main_100x100.png?v=1775718854\" alt=\"\" style=\"float: none;\"\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eHeating Oven Features\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eHeating mode: IR heating (carbon fiber), 2 kW.\u003c\/li\u003e\n\u003cli\u003eHeating chamber length: 0.5 m\u003c\/li\u003e\n\u003cli\u003eHeating temperature: Max.150℃\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eVentilation: centrifugal blower, air flow: 330m³\/h (adjustable), 3\" aluminum pipe\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\n\u003cp\u003eTension Control System\u003c\/p\u003e\n\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eTension range: 10-60 N (resolution is ±3 N), which is controlled by swing roller system.\u003c\/li\u003e\n\u003cli\u003eFor low-tension substrate coating (eg: separator and membrane), the specially designed low tension version is highly recommended since its lowest tension can be down to 5 N.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eGas Compressor\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eA gas compressor (\u003ca href=\"https:\/\/echemsupplies.com\/products\/euqofgc?variant=47513044156646\"\u003eEUQOFGC\u003c\/a\u003e) is needed to provide 60-80 psi for pneumatic operation.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/EUQOFGC_main_100x100.png?v=1775414665\" alt=\"\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL980 * W750 * H1420 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~580 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0376738818305684\"\u003eM. Cook, et al., Roll-to-roll dip coating of three different PIMs for Organic Solvent Nanofiltration, Journal of Membrane Science, 2018, 558, 52-63\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/iopscience.iop.org\/article\/10.1143\/JJAP.44.L126\/meta\"\u003eK. Fujimoto, et al., Fabrication of Layer-by-Layer Self-Assembly Films Using Roll-to-Roll Process, Jpn. J. Appl. Phys., 2005, 44, L126\u003c\/a\u003e\u003c\/p\u003e","brand":"SZKJ","offers":[{"title":"Default Title","offer_id":47524834803942,"sku":"ESMR2RDC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMR2RDC_main.png?v=1775711266"},{"product_id":"ess6pdcihs","title":"ECS-SS 6-Positions Dip Coater with Independent Heating (80℃) and Stirring, ESS6PDCIHS","description":"\u003cp\u003eA 6-position dip coater with independent heating is a high-throughput laboratory instrument designed for the precise fabrication of thin films via the sol-gel process or layer-by-layer (LbL) assembly.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eThe system typically consists of a high-precision vertical lift, a rotating carousel holding six positions, and specialized heating elements. (1) \u003cstrong\u003eMulti-Position Carousel\u003c\/strong\u003e: The 6-position design allows you to hold up to six different beakers. This is ideal for complex multilayer structures where you alternate between active materials, binders, and rinsing solutions. (2) \u003cstrong\u003eIndependent Heating\u003c\/strong\u003e: Each of the six positions is equipped with its own PID-controlled heater. This allows you to maintain one solution at room temperature (e.g., a volatile solvent) while heating another (e.g., a viscous YSZ precursor) to reduce its viscosity or trigger a specific chemical reaction. (3) \u003cstrong\u003eProgrammable Logic\u003c\/strong\u003e: You can define a complex sequence: (a) \u003cem\u003eDipping Speed\u003c\/em\u003e: Controls the initial wet film thickness. (b) \u003cem\u003eDwelling Time\u003c\/em\u003e: Time the substrate stays submerged. (c) \u003cem\u003eWithdrawal Speed\u003c\/em\u003e: The most critical factor for final dry film thickness. (4) \u003cem\u003eDrying\/Curing Time\u003c\/em\u003e: The substrate can be held above the heated beaker to accelerate solvent evaporation.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESS6PDCIHS (ESS-6PDCIHS)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 1200 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eStirring Speed: 60-300 rpm (independent setting)  \u003c\/li\u003e\n\u003cli\u003eWithdraw Speed: 1-400 mm\/min (automatic); 1-150 mm\/min (manual)\u003c\/li\u003e\n\u003cli\u003eWithdraw Times: 1-45 times\u003c\/li\u003e\n\u003cli\u003eDip Coating\/Drying Times: 1-999 s\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: 1-80 mm\u003c\/li\u003e\n\u003cli\u003e Beaker Volume: 150 mL\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: 75mm×25mm×2mm\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: 60 mm\u003c\/li\u003e\n\u003cli\u003eHeating Temperature: Max. 80℃ (independent control)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL260 * W340 * H1420 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~15 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550128292070,"sku":"ESS6PDCIHS","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_main.png?v=1776528915"},{"product_id":"essa5pdcdo","title":"ECS-SS Automatic 5-Positions Dip Coater with Drying Oven (100℃), ESSA5PDCDO","description":"\u003cp\u003eAn automatic 5-position dip coater with drying oven is a high-throughput laboratory instrument designed for the precise fabrication of thin films via the sol-gel process or layer-by-layer (LbL) assembly.\u003c\/p\u003e\n\u003cdiv style=\"text-align: start;\" data-path-to-node=\"5\"\u003e\n\u003cp\u003eThe system typically consists of a high-precision vertical lift, a rotating carousel holding six positions, and specialized heating elements. (1) \u003cstrong\u003eMulti-Position Carousel\u003c\/strong\u003e: The 6-position design allows you to hold up to six different beakers. This is ideal for complex multilayer structures where you alternate between active materials, binders, and rinsing solutions. (2) \u003cstrong\u003eIndependent Heating\u003c\/strong\u003e: Each of the six positions is equipped with its own PID-controlled heater. This allows you to maintain one solution at room temperature (e.g., a volatile solvent) while heating another (e.g., a viscous YSZ precursor) to reduce its viscosity or trigger a specific chemical reaction. (3) \u003cstrong\u003eProgrammable Logic\u003c\/strong\u003e: You can define a complex sequence: (a) \u003cem\u003eDipping Speed\u003c\/em\u003e: Controls the initial wet film thickness. (b) \u003cem\u003eDwelling Time\u003c\/em\u003e: Time the substrate stays submerged. (c) \u003cem\u003eWithdrawal Speed\u003c\/em\u003e: The most critical factor for final dry film thickness. (4) \u003cem\u003eDrying\/Curing Time\u003c\/em\u003e: The substrate can be held above the heated beaker to accelerate solvent evaporation.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg style=\"float: none;\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESSA5PDCDO (ESS-A5PDCDO)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, 2200 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: 1-200 mm\/min  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: 1-75 mm\u003c\/li\u003e\n\u003cli\u003eDipping Times; 1-20 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ≤60 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: L75mm×W25mm×T2.5mm\u003c\/li\u003e\n\u003cli\u003eBeaker Volume: Φ60 150ml (5 different dipping solutions)\u003c\/li\u003e\n\u003cli\u003eHeating Temperature: Max. 100℃ (independent PID control), heating time: 0-9999 min, 0.8 kW\u003c\/li\u003e\n\u003cli\u003eHeating Chamber Inner Sizes: 310mm×310mm×310mm (30L) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL455 * W500 * H1000 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~60 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550565581030,"sku":"ESSA5PDCDO","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSA5PDCDO_main.png?v=1776535206"},{"product_id":"essmsdcdo","title":"ECS-SS Micro-Speed (1-500um\/s) Dip Coater with Drying Oven (100℃), ESSMSDCDO","description":"\u003cp\u003eA Micro-Speed Dip Coater with Drying Oven is a specialized thin-film fabrication unit designed for research where ultra-thin, uniform coatings are required from low-viscosity solutions or slurries.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003e\u003cstrong\u003eMicro-Speed Drive\u003c\/strong\u003e: Unlike standard coaters, a micro-speed unit uses high-resolution stepper motors or piezo-drives to achieve withdrawal speeds as low as 0.1 um\/s. This is essential for the \"Capillary Regime\" of coating, where the film thickness is extremely thin (\u0026lt;100 nm). (2) \u003cstrong\u003eIntegrated Oven\u003c\/strong\u003e: The heating chamber is typically positioned above the dipping beaker. As the substrate is withdrawn, it enters a temperature-controlled environment (up to 200°C or higher). (a) \u003cem\u003eSolvent Management\u003c\/em\u003e: Immediate heating ensures that the solvent (like NMP or Terpineol) evaporates at a rate that matches the withdrawal speed, locking the particles (e.g., YSZ or GDC) in place. (b) \u003cem\u003ePre-heating\u003c\/em\u003e: Some systems allow the substrate to be pre-heated before dipping to alter the wetting behavior.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESSMSDCDO (ESS-MSDCDO)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC110V or 220V±10%, single phase, 50\/60Hz, 700 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: 1-500 um\/s  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: 1-75 mm\u003c\/li\u003e\n\u003cli\u003eDipping Times; 1-20 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ≤60 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: L75mm×W25mm×T2.5mm. Two samples can be clamped at the same time.\u003c\/li\u003e\n\u003cli\u003eBeaker Volume: Φ60 150ml\u003c\/li\u003e\n\u003cli\u003eHeating Temperature: Max. 100℃ (independent PID control), heating time: 0-9999 min, 0.8 kW\u003c\/li\u003e\n\u003cli\u003eHeating Chamber Inner Sizes: 310mm×310mm×310mm (30L) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL430 * W500 * H1000 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~50 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550611652838,"sku":"ESSMSDCDO","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMSDCDO_main.png?v=1776537039"},{"product_id":"essnsdcdo","title":"ECS-SS Nano-Speed (10-500 nm\/s) Dip Coater with Drying Oven (100℃), ESSNSDCDO","description":"\u003cp\u003eA Nano-Speed Dip Coater with Drying Oven is the most precise iteration of dip-coating technology, specifically designed for \"Bottom-Up\" nanotechnology and the fabrication of ultra-thin, highly ordered monolayers or sub-micron ceramic membranes.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eStandard dip coaters operate in the millimeter-per-minute range. A Nano-Speed unit utilizes specialized high-resolution piezo-drives or micro-stepping lead screws to achieve withdrawal speeds as low as 0.1 nm\/s to 10 nm\/s. (1) \u003cstrong\u003eEvaporation-Regime Coating\u003c\/strong\u003e: At these ultra-low speeds, the film formation is no longer governed by fluid dynamics (Landau-Levich) but by the rate of solvent evaporation at the meniscus (the \"Coffee Ring\" effect utilized for uniform coating). (2) \u003cstrong\u003eMolecular Assembly\u003c\/strong\u003e: This speed range is critical for Layer-by-Layer (LbL) assembly and the deposition of 2D materials (like graphene or MXenes) where you need to allow time for molecules to orient themselves on the substrate surface.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESSNSDCDO (ESS-NSDCDO)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC110V or 220V±10%, single phase, 50\/60Hz, 700 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e10-500 nm\/s \u003c\/span\u003e \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: 1-75 mm\u003c\/li\u003e\n\u003cli\u003eDipping Times; 1-20 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ≤60 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: L75mm×W25mm×T2.5mm. Two samples can be clamped at the same time.\u003c\/li\u003e\n\u003cli\u003eBeaker Volume: Φ60 150ml\u003c\/li\u003e\n\u003cli\u003eHeating Temperature: Max. 100℃ (independent PID control), heating time: 0-9999 min, 0.8 kW\u003c\/li\u003e\n\u003cli\u003eHeating Chamber Inner Sizes: 310mm×310mm×310mm (30L) \u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL430 * W500 * H1000 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~50 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550631018726,"sku":"ESSNSDCDO","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSMSDCDO_main.png?v=1776537039"},{"product_id":"esmpdc","title":"ECS-SM Programmable Dip Coater (Sample: L310*W260*T5mm), ESMPDC","description":"\u003cp\u003eA Programmable Dip Coater for medium sample sizes is designed for laboratories moving beyond small coupons (like 1cm * 1cm) toward larger substrates such as planar SOFC plates or battery electrode foils (100 mm * 100 mm to 200 mm * 200 mm).\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eAs substrate size increases, the mass and surface tension forces change. A medium-sized programmable unit addresses this with: (1) \u003cstrong\u003eHigh-Torque Stepper Motors\u003c\/strong\u003e: Ensures smooth, vibration-free movement even with heavier substrates (e.g., thick Ni-YSZ porous supports). (2) \u003cstrong\u003eExtended Vertical Travel\u003c\/strong\u003e: Typically offers 200 mm to 300 mm of stroke to allow full immersion of medium-sized plates into deep beakers. (3) \u003cstrong\u003eComplex Motion Profiles\u003c\/strong\u003e: Programming isn't just about speed; you can set \"multi-dwell\" profiles where the substrate stays submerged for different durations at different depths to manage gradient coatings.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESMPDC (ESM-PDC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, single phase, 50\/60Hz, 100 W (DC24 V)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: 1-200 mm\/min  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: 1-270 mm\u003c\/li\u003e\n\u003cli\u003eDipping Times; 1-20 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ~200 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: Max. L310mm×W260mm×T5mm\u003c\/li\u003e\n\u003cli\u003eWithdraw Loading Mass: Max. 5.5 kg \u003c\/li\u003e\n\u003cli\u003eAcrylic Tank Volume: L340 * W50 * H280 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL455 * W330 * H890 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~20 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550641111270,"sku":"ESMPDC","price":4999.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESMPDC_main.png?v=1776540338"},{"product_id":"eslpdc","title":"ECS-SL Large Programmable Dip Coater (Sample: L310*W260*T5mm), ESLPDC","description":"\u003cp\u003eA Programmable Dip Coater for medium sample sizes is designed for laboratories moving beyond small coupons (like 1cm * 1cm) toward larger substrates such as planar SOFC plates or battery electrode foils (100 mm * 100 mm to 200 mm * 200 mm).\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eAs substrate size increases, the mass and surface tension forces change. A medium-sized programmable unit addresses this with: (1) \u003cstrong\u003eHigh-Torque Stepper Motors\u003c\/strong\u003e: Ensures smooth, vibration-free movement even with heavier substrates (e.g., thick Ni-YSZ porous supports). (2) \u003cstrong\u003eExtended Vertical Travel\u003c\/strong\u003e: Typically offers 200 mm to 300 mm of stroke to allow full immersion of medium-sized plates into deep beakers. (3) \u003cstrong\u003eComplex Motion Profiles\u003c\/strong\u003e: Programming isn't just about speed; you can set \"multi-dwell\" profiles where the substrate stays submerged for different durations at different depths to manage gradient coatings.\u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESLPDC (ESL-PDC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC110-220V±10%, single phase, 50\/60Hz, ~300 W (DC24 V)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: 10-1000 mm\/min  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e1-350 mm\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eDipping Times; 1-20 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ~300 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: Max. \u003cspan style=\"color: rgb(255, 42, 0);\"\u003eL640mm×W315mm×T5mm\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eWithdraw Loading Mass: Max. 5.5 kg \u003c\/li\u003e\n\u003cli\u003eAcrylic Tank Volume: L640 * W50 * H335 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL670 * W380 * H860 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~20 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550731124966,"sku":"ESLPDC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESLPDC_main.png?v=1776540845"},{"product_id":"esspdc3hzf","title":"ECS-SS Programmable Dip Coater with Three Heating Zone Furnace (1000℃), ESSPDC3HZF","description":"\u003cp\u003eA Programmable Dip Coater with a Three-Heating Zone Tube Furnace ($1000\\text{°C}$) is a sophisticated integrated system designed for the one-step fabrication and thermal processing of thin films. This setup allows you to dip-coat a substrate and then immediately lift it into a high-temperature furnace for drying, calcination, or sintering—all without exposing the \"green\" film to the ambient atmosphere or manual handling.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003e\u003cstrong\u003eVertical Lift Mechanism\u003c\/strong\u003e: A high-precision programmable motor moves the substrate vertically through the bottom of the furnace and into the precursor beaker. \u003cstrong\u003eThree-Zone Furnace\u003c\/strong\u003e: Unlike single-zone furnaces, the three-zone design (1000 °C) allows for a precise thermal gradient. The bottom zone typically kept cooler for initial solvent evaporation and stabilization, while the middle\/top zones are heated to the target sintering temperature to trigger phase formation and densification. \u003c\/p\u003e\n\u003cp\u003eDip Coating Process Sketch and Working Mechanism\u003c\/p\u003e\n\u003cp\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS6PDCIHS_02_160x160.png?v=1776528915\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESSPDC3HZF (ESS-PDC3HZF)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, ~3000 W\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: DC24V adaptor, 50W, high precision step motor\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: Three stage with independent speed setting, 1-200 mm\/min  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDrying\/Dwelling Times: 1-999 s\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTotal Traverse Distance (three zones): \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e~620 mm\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli style=\"color: rgb(0, 0, 0);\"\u003e\u003cspan style=\"color: rgb(0, 0, 0);\"\u003eFirst Low Temperature Region: 236 mm (fixed)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cspan style=\"color: rgb(0, 0, 0);\"\u003eSecond High Temperature Region: 150 mm (fixed)\u003c\/span\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan style=\"color: rgb(0, 0, 0);\"\u003eThird Cooling Region: 234 mm (fixed)\u003c\/span\u003e\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eEffective Dip Coating Length: ~60 mm\u003c\/li\u003e\n\u003cli\u003eAcceptable Sample Sizes: Max. \u003cspan style=\"color: rgb(255, 42, 0);\"\u003eL75mm×W25mm×T4mm\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eWithdraw Loading Mass: Max. 200 g\u003c\/li\u003e\n\u003cli\u003eHeating Temperature: Max. 1000℃ (RT-800℃ is recommended)\u003c\/li\u003e\n\u003cli\u003eTemperature Control Accuracy: ±1℃ (K-type thermocouple)\u003c\/li\u003e\n\u003cli\u003eFurnace Processing Tube: O.D. Φ50mm× I.D. φ45mm× L600mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL560 * W470 * H1550 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~20 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550762254566,"sku":"ESSPDC3HZF","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESSPDC3HZF_main.png?v=1776545637"},{"product_id":"ess4paadc","title":"ECS-SS 4-Positions Angle-Adjustable Dip Coater, ESS4PAADC","description":"\u003cp\u003eA 4-Positions Angle-Adjustable Dip Coater is a specialized thin-film deposition system designed to overcome the limitations of standard vertical dipping. By allowing the substrate to enter the solution at a specific angle (typically 0° to 90°), this machine provides a unique method to control film thickness, meniscus behavior, and coating uniformity on both sides of a substrate.\u003c\/p\u003e\n\u003cdiv data-path-to-node=\"5\" style=\"text-align: start;\"\u003e\n\u003cp\u003eIn standard vertical dipping, gravity and surface tension pull the liquid straight down, often leading to a \"wedge effect\" (thicker at the bottom). Adjusting the angle changes the physics of the meniscus: (1) \u003cstrong\u003eMeniscus Control\u003c\/strong\u003e: A tilted entry changes the contact angle of the liquid on the substrate. This can help \"stretch\" the meniscus, leading to thinner and more uniform coatings at higher speeds than vertical dipping allows. (2) \u003cstrong\u003eSingle-Side Coating Bias\u003c\/strong\u003e: If a high-quality coating on one side of a Ni-YSZ support is required, dipping at an angle can change how the liquid drains off the \"back\" side compared to the \"front\" side. (3) \u003cstrong\u003eAsymmetric Substrates\u003c\/strong\u003e: For substrates with complex geometries or surface textures, an angled entry prevents air bubbles from being trapped in the pores—a common failure point in SOFC electrolyte deposition.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003ctable width=\"100%\"\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePart Number\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eESS4PAADC (ESS-4PAADC)\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003ePower\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eAC220V±10%, single phase, 50\/60Hz, ~800 W\u003c\/li\u003e\n\u003cli\u003eAC110V can be realized by a 1000 W transformer\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eMain Parameters\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cul\u003e\n\u003cli\u003eDriven Motor: Servo motor with guiding screw rod\u003c\/li\u003e\n\u003cli\u003eDipping\/Withdraw Speed: 2 um\/s to 9 mm\/s (adjustable)  \u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eDipping Times: 1-999 times\u003cbr\u003e\n\u003c\/li\u003e\n\u003cli\u003eTraverse Distance: \u003cspan style=\"color: rgb(255, 42, 0);\"\u003e~75 mm\u003c\/span\u003e\u003cspan style=\"color: rgb(0, 0, 0);\"\u003e\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003eFour 150 mL beakers are included. \u003c\/li\u003e\n\u003cli\u003eSample holder is show below:\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e          \u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS4PAADC_02_100x100.png?v=1776577264\" alt=\"\" style=\"float: none;\"\u003e\u003c\/p\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eCertification\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eCE certified\u003c\/li\u003e\n\u003cli\u003eUL and CSA certification is available upon request at extra cost\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eDimension\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003eL570 * W300 * H480 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cem\u003eWeight\u003c\/em\u003e\u003c\/td\u003e\n\u003ctd\u003e\n\u003cdiv\u003e\n\u003cul\u003e\n\u003cli\u003e~23 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eReferences\u003c\/strong\u003e:\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/pubs.acs.org\/doi\/abs\/10.1021\/acsami.2c07292\"\u003eT. T. Wu, et al., Facile Construction of Nanofilms from a Dip-Coating Process to Enable High-Performance Solid-State Batteries, ACS Appl. Mater. Interfaces 2022, 14, 28, 32026–32034\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/link.springer.com\/article\/10.1007\/s12274-017-1771-4\"\u003eH. W. Zhu, et al., Dip-coating processed sponge-based electrodes for stretchable Zn-MnO2 batteries, Nano Research, 2018, 11, 1554–1562\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003e\u003ca href=\"https:\/\/www.sciencedirect.com\/science\/article\/abs\/pii\/S0378775320302664\"\u003eX. Peng, et al., Improved battery safety via in-situ dip-coated composite gel polymer electrolytes, Journal of Power Sources, 2020, 455, 227963\u003c\/a\u003e. \u003c\/p\u003e","brand":"SYKJ","offers":[{"title":"Default Title","offer_id":47550857085158,"sku":"ESS4PAADC","price":8888888.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/files\/ESS4PAADC_main.png?v=1776577198"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0774\/6591\/1526\/collections\/ESMR2RDC_main.png?v=1776022163","url":"https:\/\/echemsupplies.com\/collections\/dip-coaters.oembed","provider":"EChem Supplies","version":"1.0","type":"link"}